GTS Ethernet Intel® FPGA Hard IP User Guide

Download PDF
ID 817676
Date 10/12/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Install and License the GTS Ethernet Intel® FPGA Hard IP 3. Configure and Generate Ethernet Hard IP variant 4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application 5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance 6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance 7. Simulate, Compile, and Validate SyncE - Single Instance 8. Simulate and Compile PTP1588 - Single Instance 9. Simulate, Compile, and Validate - Multiple Instance 10. Simulate, Compile, and Validate - Auto-Negotiation and Link Training 11. Troubleshoot and Diagnose Issues A. Appendix A: Functional Description B. Appendix B: Configuration Registers C. Appendix C: Document Revision History for the GTS Ethernet Intel® FPGA Hard IP User Guide
1. Overview x
1.1. Release Information 1.2. High-Level Functional Overview 1.3. Acronyms 1.4. Agilex™ 5 Ethernet Portfolio and Target Applications 1.5. Agilex™ 5 Ethernet Hard IP Features 1.6. GTS Ethernet Intel® FPGA Hard IP Design Flow
1.5. Agilex™ 5 Ethernet Hard IP Features x
1.5.1. Device Family Support 1.5.2. Device Speed Grade Support 1.5.3. Resource Utilization
3. Configure and Generate Ethernet Hard IP variant x
3.1. Create Quartus Project 3.2. Configure GTS Ethernet Hard IP 3.3. Generate HDL for Synthesis and Simulation 3.4. Generated File Structure 3.5. Generate GTS EHIP Design Example 3.6. Analog Parameter Options
3.5. Generate GTS EHIP Design Example x
3.5.1. Directory Structure
4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application x
4.1. Implement Required Clocking 4.2. Implement Required Resets 4.3. Connect the Status Interface 4.4. Connect the MAC Avalon Streaming Client Interface 4.5. Connect the MII PCS Only Client Interface 4.6. Connect the PCS66 Client Interface – FlexE and OTN 4.7. Connect the Precision Time Protocol Interface 4.8. Connect the Ethernet Hard IP Reconfiguration Interface 4.9. Connect the Auto-Negotiation and Link Training
4.1. Implement Required Clocking x
4.1.1. Implement MAC Synchronous Clock Connections to Single Instance 4.1.2. Implement MAC Synchronous Clock Connections to Multiple Instances 4.1.3. Implement Clock Connections to MAC Asynchronous Operation 4.1.4. Implement Clock Connections in Synchronous Ethernet Operation (Sync-E) 4.1.5. Implement Clock Connections in PTP-Based Design
4.2. Implement Required Resets x
4.2.1. Reset Sequence 4.2.2. Connect the GTS Reset Sequencer Intel® FPGA IP
4.2.2. Connect the GTS Reset Sequencer Intel® FPGA IP x
4.2.2.1. Requirements and Considerations for GTS Reset Sequencer Intel® FPGA IP
4.3. Connect the Status Interface x
4.3.1. Use i_stats_snapshot to Read Stats Counters
4.4. Connect the MAC Avalon Streaming Client Interface x
4.4.1. Connect the TX MAC Avalon Streaming Client Interface 4.4.2. Connect the RX MAC Avalon Streaming Client Interface 4.4.3. Connect the MAC Flow Control Interface
4.4.1. Connect the TX MAC Avalon Streaming Client Interface x
4.4.1.1. Drive the Ethernet Packet to the TX MAC Avalon Streaming Client Interface with Disabled Preamble Passthrough 4.4.1.2. Drive the Ethernet Packet on the TX MAC Avalon Streaming Client Interface with Enabled Preamble Passthrough 4.4.1.3. Use i_tx_skip_crc to Control Source Address, PAD, and CRC Insertion 4.4.1.4. Assert the i_tx_error to Invalidate a Packet
4.4.2. Connect the RX MAC Avalon Streaming Client Interface x
4.4.2.1. Receive Ethernet Frame on the RX MAC Avalon Streaming Client Interface with Preamble Passthrough Disabled 4.4.2.2. Receive Ethernet Frame with Preamble Passthrough Enabled 4.4.2.3. Receive Ethernet Frame with Remove CRC bytes Disabled 4.4.2.4. Monitor Status and Errors on the RX MAC Avalon Streaming Client Interface
4.4.3. Connect the MAC Flow Control Interface x
4.4.3.1. Connect the TX MAC Flow Control Interface 4.4.3.2. Connect the RX MAC Flow Control Interface
4.5. Connect the MII PCS Only Client Interface x
4.5.1. Connect the MII PCS Mode TX Interface 4.5.2. Connect the MII PCS Mode RX Interface
4.5.1. Connect the MII PCS Mode TX Interface x
4.5.1.1. Insert Alignment Marker
4.5.2. Connect the MII PCS Mode RX Interface x
4.5.2.1. Receive Alignment Marker
4.6. Connect the PCS66 Client Interface – FlexE and OTN x
4.6.1. Connect the FlexE and OTN Mode TX Interface 4.6.2. Connect the FlexE and OTN Mode RX Interface
4.6.1. Connect the FlexE and OTN Mode TX Interface x
4.6.1.1. Insert Alignment Marker
4.6.2. Connect the FlexE and OTN Mode RX Interface x
4.6.2.1. Receive Alignment Marker
4.7. Connect the Precision Time Protocol Interface x
4.7.1. Connect the Time-of-Day Interface 4.7.2. Connect the TX Two-Step Timestamp Interface 4.7.3. Connect the TX One-Step Timestamp Interface 4.7.4. Connect the RX Timestamp Interface 4.7.5. Connect the PTP Status Interface
4.7.3. Connect the TX One-Step Timestamp Interface x
4.7.3.1. PTP Field Offset for 1-Step Operation
5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance x
5.1. Design Example Features 5.2. Design Example Components 5.3. Simulate the Design Example 5.4. Compile the Design Example 5.5. Validate the Design Example
5.3. Simulate the Design Example x
5.3.1. Simulation Testbench Flow 5.3.2. Verify the Simulation Results
5.5. Validate the Design Example x
5.5.1. Configure the Clocks in Hardware 5.5.2. Program the FPGA 5.5.3. Run the Hardware Test
6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance x
6.1. Design Example Features 6.2. Design Example Components 6.3. Simulate the Design Example 6.4. Compile the Design Example 6.5. Validate the Design Example
6.3. Simulate the Design Example x
6.3.1. Simulation Testbench Flow 6.3.2. Simulators Output
6.5. Validate the Design Example x
6.5.1. Configure the Clocks in Hardware 6.5.2. Program the FPGA 6.5.3. Run the Hardware Test
7. Simulate, Compile, and Validate SyncE - Single Instance x
7.1. Design Example Features 7.2. Design Example Components 7.3. Simulate the Design Example 7.4. Compile the Design Example 7.5. Validate the Design Example
7.3. Simulate the Design Example x
7.3.1. Simulation Testbench Flow for Single Instance with SyncE 7.3.2. Simulator Output
7.5. Validate the Design Example x
7.5.1. Configure the Clocks in Hardware 7.5.2. Program the FPGA 7.5.3. Run the Hardware Test
8. Simulate and Compile PTP1588 - Single Instance x
8.1. Design Example Features 8.2. Design Example Components 8.3. Simulate the Design Example 8.4. Compile the Design Example 8.5. Validate the Design Example
8.3. Simulate the Design Example x
8.3.1. Simulation Testbench Flow 8.3.2. Simulator Output
8.5. Validate the Design Example x
8.5.1. Configure the Clocks in Hardware 8.5.2. Program the FPGA 8.5.3. Run the Hardware Test
9. Simulate, Compile, and Validate - Multiple Instance x
9.1. Design Example Features 9.2. Design Example Components 9.3. Simulate the Design Example 9.4. Compile the Design Example 9.5. Validate the Design Example
9.3. Simulate the Design Example x
9.3.1. Simulation Testbench Flow for MAC Mode 9.3.2. Simulator Output
9.5. Validate the Design Example x
9.5.1. Configure the Clocks in Hardware 9.5.2. Program the FPGA 9.5.3. Run the Hardware Test
10. Simulate, Compile, and Validate - Auto-Negotiation and Link Training x
10.1. Design Example Features 10.2. Design Example Components 10.3. Simulate the Design Example 10.4. Compile the Design Example 10.5. Validate the Design Example
10.3. Simulate the Design Example x
10.3.1. Simulation Testbench Flow 10.3.2. Simulation Output
10.5. Validate the Design Example x
10.5.1. Configure the Clocks in Hardware 10.5.2. Program the FPGA 10.5.3. Run the Hardware Test
11. Troubleshoot and Diagnose Issues x
11.1. Enable Diagnostic Lookback Modes 11.2. Troubleshoot the Reset Sequence 11.3. Use Signal Tap Analyzer for Troubleshooting
11.1. Enable Diagnostic Lookback Modes x
11.1.1. Internal Serial Loopback 11.1.2. Enable MAC Loopback 11.1.3. Enable PCS Loopback 11.1.4. Enable External Loopback 11.1.5. Packet Client Loopback
11.2. Troubleshoot the Reset Sequence x
11.2.1. Debug the Power Up Reset Sequence 11.2.2. Debug the TX Reset Entry Sequence 11.2.3. Debug the TX Reset Exit Sequence 11.2.4. Debug the RX Reset Entry Sequence 11.2.5. Debug the RX Reset Exit Sequence 11.2.6. Debug the Auto Recovery Reset Sequence
A. Appendix A: Functional Description x
A.1. Datapath Description A.2. GTS Ethernet Intel® FPGA Hard IP MAC A.3. PCS, OTN, and FlexE Modes A.4. Precision Time Protocol Interface A.5. Auto-Negotiation and Link Training
A.2. GTS Ethernet Intel® FPGA Hard IP MAC x
A.2.1. MAC TX Datapath A.2.2. MAC RX Datapath A.2.3. Congestion and Flow Control Using PAUSE or Priority Flow Control (PFC) A.2.4. Link Fault Signaling A.2.5. Order of Ethernet Transmission:
A.2.1. MAC TX Datapath x
A.2.1.1. Insert TX Preamble, Start, and SFD A.2.1.2. Insert Source Address A.2.1.3. Process Length/Type Field A.2.1.4. Pad the Client Frame A.2.1.5. Insert Frame Check Sequence (CRC-32) A.2.1.6. Generate and Insert Inter-Packet Gap
A.2.2. MAC RX Datapath x
A.2.2.1. Process RX Preamble A.2.2.2. Check RX Strict SFD A.2.2.3. Check RX FCS A.2.2.4. Handle RX Malformed Packet A.2.2.5. Remove PAD Bytes and FCS Bytes from RX Frames A.2.2.6. RX Undersized Frames, Oversized Frames, and Frames with Length Errors A.2.2.7. Inter-Packet Gap
A.2.3. Congestion and Flow Control Using PAUSE or Priority Flow Control (PFC) x
A.2.3.1. Conditions Triggering XOFF Frame Transmission A.2.3.2. Conditions Triggering XON Frame Transmission A.2.3.3. Pause Control and Generation Interface A.2.3.4. Pause Control Frame Filtering
A.3. PCS, OTN, and FlexE Modes x
A.3.1. PCS Mode A.3.2. OTN Mode A.3.3. FlexE Mode
A.4. Precision Time Protocol Interface x
A.4.1. Features A.4.2. PTP User Flow A.4.3. Make PTP UI Adjustments A.4.4. Reference Time Interval A.4.5. Minimum and Maximum Reference Time (TAM) Interval for UI Measurement (Hardware)
A.4.2. PTP User Flow x
A.4.2.1. PTP TX User Flow A.4.2.2. PTP RX User Flow
A.4.3. Make PTP UI Adjustments x
A.4.3.1. Adjust TX UI A.4.3.2. Adjust RX UI
B. Appendix B: Configuration Registers x
B.1. Ethernet Avalon® Memory-Mapped Interface Address Space B.2. Packet Client Registers
1. Overview
2. Install and License the GTS Ethernet Intel® FPGA Hard IP
3. Configure and Generate Ethernet Hard IP variant
4. Integrate GTS Ethernet Intel® FPGA Hard IP into Your Application
5. Simulate, Compile, and Validate (MAC+PCS) - Single Instance
6. Simulate, Compile, and Validate (MII PCS Only /PCS66 OTN/PCS66 FlexE) - Single Instance
7. Simulate, Compile, and Validate SyncE - Single Instance
8. Simulate and Compile PTP1588 - Single Instance
9. Simulate, Compile, and Validate - Multiple Instance
10. Simulate, Compile, and Validate - Auto-Negotiation and Link Training
11. Troubleshoot and Diagnose Issues
A. Appendix A: Functional Description
B. Appendix B: Configuration Registers
C. Appendix C: Document Revision History for the GTS Ethernet Intel® FPGA Hard IP User Guide

4.9. Connect the Auto-Negotiation and Link Training

The following four components are required to create an Ethernet Port with AN/LT IP enabled.
  • The central component is the Ethernet Hard IP.
  • The second component is the AN/LT IP which drives the AN/LT process.
  • The third component is a System PLL IP which generates a system clock for the Ethernet IP.
  • The fourth component is the Reset Sequencer IP which is used to stagger resets to prevent power-droop glitches.

The following diagram shows the interconnection signals required for Ethernet with AN/LT. Once the four required components are generated, connect them as shown in the diagram.

Figure 53. Auto-Negotiation and Link Training for GTS Ethernet Intel® FPGA Hard IP
Table 46.  Clock and Reset Ports
Name Description
i_clk Clock source with 100 MHz frequency. When AN/LT is enabled, drive the i_clk at 1 GHz for faster simulation times.
i_reset Active high reset, synchronous to i_clk clock.
Table 47.  User Avalon® Memory-Mapped Interface PortsThe following interface signals are clocked by the i_clk_signal and are used for read/write access to the AN/LT IP registers.
Name Width Description
i_kr_reconfig_addr[11:0] 12 Address bus for auto-negotiation and link training control and status registers (AN/LT CSRs).
  • Bits [11:8]: Port number
  • [7:0]: CSR space for each port
i_kr_reconfig_read 1 Read enable for AN/LT CSRs.
i_kr_reconfig_write 1 Write enable for AN/LT CSRs.
i_kr_reconfig_byte_en[3:0] 4 AN/LT byte enable signal for writing data.
i_kr_reconfig_writedata[31:0] 32 Write data for AN/LT CSRs.
o_kr_reconfig_readdata[31:0] 32 Read data from AN/LT CSRs.
o_kr_reconfig_readdata_valid 1 Valid signal for AN/LT CSRs read data. When asserted, the register is valid.
o_kr_reconfig_waitrequest 1 Indicates that the Avalon® memory-mapped interface is busy. The read or write cycle is only complete when this signal goes low.
Table 48.  Local Avalon Memory-Mapped Interface Ports to Connect to Base Ethernet IP Transceiver ChannelsThe i_clk_signal clocks the interface signals below, which connect each set of Avalon Memory-Mapped signals to a transceiver channel.

<prt_num> goes from 0 to 15 based on the number of ports selected.

Name Width Description
kr_xcvr_0_reconfig_addr[17:0] 18 Address for transceiver
kr_ xcvr_0_reconfig_read 1 Read enable for transceiver registers.
kr_ xcvr_0_reconfig_write 1 Write enable for transceiver registers.
kr_xcvr_0_reconfig_byte_en[3:0] 4 Data byte enable for transceiver registers.
kr_xcvr_0_reconfig_writedata[31:0] 32 Write data for transceiver registers.
xcvr_kr_0_reconfig_readdata[31:0] 32 Read data for transceiver registers.
xcvr_kr_0_reconfig_readdata_valid 1 Valid signal for AN/LT CSRs read data. When asserted, the register is valid.
xcvr_kr_0_reconfig_waitrequest 1 Indicates that the local Avalon® memory-mapped interface is busy. The read or write cycle is only complete when this signal goes low.
Table 49.  KR status and Control Signals to connect to Base IP Transceiver ChannelsThe table below illustrates the connections for each set of kr_stat and kr_ctrl signals to the Ethernet SIP.
Name Width Description
kr_ctrl_xcvr_<prt_num>[0] 1 TX/RX lane desired signal controls the SRC (Soft Reset Controller) state when the kr_mode signal is set to active.
kr_ctrl_xcvr_<prt_num>[1] 1 Kr_mode signal that allows KR IP to set the TX/RX SRC desired lane states.
kr_ctrl_xcvr_<prt_num>[2] 1 The Kr_fec_mode signal indicates that the FEC mode is enabled.
kr_ctrl_xcvr_<prt_num>[3] 1 The TX/RX freeze SRC signal becomes active when the kr_mode signal is set.
kr_ctrl_xcvr_<prt_num>[7:4] 4 Reserved.
kr_stat_xcvr_<prt_num>[0] 1 Indicates KR reset ACK (acknowledgment) signal is set.
kr_stat_xcvr_<prt_num>[1] 1 Indicates that the PCS is fully aligned.
kr_stat_xcvr_<prt_num>[2] 1 Indicates that the HI BER (High Bit Error Rate) signal is set.
kr_stat_xcvr_<prt_num>[3] 1 Indicates that both TX/RX Freeze SRC ACK signals are set.
kr_stat_xcvr_<prt_num>[7:4] 4 Reserved.
Level Two Title