Visible to Intel only — GUID: ono1684441890375
Ixiasoft
1. GTS Transceiver Overview
2. GTS Transceiver Architecture
3. Implementing the GTS PMA/FEC Direct PHY Intel FPGA IP
4. Implementing the GTS System PLL Clocks Intel FPGA IP
5. Implementing the GTS Reset Sequencer Intel FPGA IP
6. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
7. Design Assistance Tools
8. Debugging GTS Transceiver Links with Transceiver Toolkit
9. Document Revision History for the GTS Transceiver PHY User Guide
3.1. IP Overview
3.2. Designing with the GTS PMA/FEC Direct PHY Intel FPGA IP
3.3. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP
3.4. Signal and Port Reference
3.5. Bit Mapping for PMA and FEC Mode PHY TX and RX Datapath
3.6. Clocking
3.7. Custom Cadence Generation Ports and Logic
3.8. Asserting reset
3.9. Bonding Implementation
3.10. Configuration Register
3.11. Configuring the GTS PMA/FEC Direct PHY Intel FPGA IP for Hardware Testing
3.12. Configurable Quartus® Prime Software Settings
3.13. Hardware Configuration Using the Avalon® Memory-Mapped Interface
3.4.1. TX and RX Parallel and Serial Interface Signals
3.4.2. TX and RX Reference Clock and Clock Output Interface Signals
3.4.3. Reset Signals
3.4.4. FEC Signals
3.4.5. PCS Direct Signals: IEEE
3.4.6. PCS Direct Signals: IEEE_FLEXE_66/PCS66
3.4.7. Custom Cadence Control and Status Signals
3.4.8. RX PMA Status Signals
3.4.9. TX and RX PMA and Core Interface FIFO Signals
3.4.10. Avalon Memory-Mapped Interface Signals
3.8.1. Reset Signal Requirements
3.8.2. Power On Reset Requirements
3.8.3. Reset Signals—Block Level
3.8.4. Run-time Reset Sequence—TX
3.8.5. Run-time Reset Sequence—RX
3.8.6. Run-time Reset Sequence—TX + RX
3.8.7. Run-time Reset Sequence—TX with FEC
3.8.8. RX Data Loss/CDR Lock Loss (Auto-Recovery)
3.8.9. TX PLL Lock Loss
6.1. Instantiating the GTS PMA/FEC Direct PHY Intel FPGA IP
6.2. Generating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
6.4. Simulating the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Testbench
6.5. Compiling the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
6.6. Hardware Testing the GTS PMA/FEC Direct PHY Intel FPGA IP Example Design
Visible to Intel only — GUID: ono1684441890375
Ixiasoft
6.3. GTS PMA/FEC Direct PHY Intel FPGA IP Example Design Functional Description
The GTS PMA/FEC Direct PHY Intel FPGA IP example design simulation testbench top-level block diagram is shown in the following figure.
Figure 84. Simulation Testbench Block Diagram for the GTS PMA/FEC Direct PHY Intel Example Design
This section provides the functional description of the example design and the simulation results for both the PMA and FEC direct designs listed in the following table.
The testbench program controls the testbench components through the Avalon® memory-mapped interface. For both the PMA and FEC direct example designs, the testwrap block consists of the PRBS generator, PRBS verifier, and TX and RX clock output frequency checkers. There are 3 types of test wrap blocks:
Example Design Option | Functional Description |
---|---|
1 x 10.3125G FEC Direct Mode (System PLL Clocking) | One NRZ FEC Direct GTS lane operating at 10.3125 Gbps with System PLL clocking mode |
4 x 10.3125G PMA Direct Mode (PMA Clocking) | Four NRZ PMA Direct GTS lane operating at 10.3125 Gbps per PMA lane with PMA clocking mode |
- PMA test wrap – used in PMA direct configurations.
- FEC test wrap – used in FEC direct configuration.
- PCS test wrap - used in PCS direct configuration.
The clock sources for the example design are shown in the following table.
Example Design Option | Clock Source Connections |
---|---|
1 x 10.3125G FEC Direct Mode (System PLL Clocking) |
|
4 x 10.3125G PMA Direct Mode (PMA Clocking) |
|