Visible to Intel only — GUID: krz1662081106307
Ixiasoft
HSIO Single-Ended I/O Standards Specifications
HSIO Single-Ended SSTL, HSTL, HSUL, and POD I/O Reference Voltage Specifications
HSIO Single-Ended SSTL, HSTL, HSUL, and POD I/O Standards Signal Specifications
HSIO Single-Ended LVSTL I/O Standards Specifications
HSIO Differential SSTL, HSTL, and HSUL I/O Standards Specifications
HSIO Differential POD I/O Standards Specifications
HSIO Differential LVSTL I/O Standards Specifications
HSIO Differential I/O Standards Specifications
MIPI D-PHY I/O Standards Specifications
HPS Clock Performance
HPS Internal Oscillator Frequency
HPS PLL Specifications
HPS Cold Reset
HPS SPI Timing Characteristics
HPS SD/eMMC Timing Characteristics
HPS USB 2.0 Timing Characteristics
HPS USB 3.1 Timing Characteristics
HPS Ethernet Media Access Controller (EMAC) Timing Characteristics
HPS I2C Timing Characteristics
HPS I3C Timing Characteristics
HPS NAND Timing Characteristics
HPS Trace Timing Characteristics
HPS GPIO Interface
HPS JTAG Timing Characteristics
HPS Programmable I/O Timing Characteristics
Visible to Intel only — GUID: krz1662081106307
Ixiasoft
GTS Transceiver Power Supply Operating Conditions
Symbol | Description | Typical DC Level (V) | Recommended VR Accuracy (% of Typical DC Level) | Recommended VR Ripple (% of Typical DC Level) | Recommended AC Transient (% of Typical DC Level) | Maximum (VR Accuracy + Ripple + AC Transient) (% of Typical DC Level)50 | Unit | |
---|---|---|---|---|---|---|---|---|
VCC_HSSI_[L1, R4] | Transceiver, system PLL, and hard IP digital power supply | 0.8 | ±0.5 | ±2.5 | ±3 | V | ||
VCCEHT_GTS[L1, R4][A, B, C, D] 51 | Transceiver PMA, transceiver PLL, and transceiver reference clock high voltage analog power supply | 1.8 | ±0.5 | ±2.0 | ±2.5 | V | ||
VCCERT_GTS[L1, R4][A, B, C, D] | Transceiver PMA and transceiver reference clock low voltage analog power supply | 1 | ±0.5 | ±2.0 | ±2.5 | V |
Symbol | Description | Speed Grade | Typical DC Level (V) | Recommended VR Accuracy (% of Typical DC Level) | Recommended VR Ripple (% of Typical DC level) | Recommended AC Transient (% of Typical DC level) | Maximum (VR Accuracy + Ripple + AC Transient) (% of Typical DC Level)52 | Unit |
---|---|---|---|---|---|---|---|---|
VCC_HSSI_[L1, R4] | Transceiver, system PLL, and hard IP digital power supply | –6S, –6X | 0.75 | ±0.5 | ±2.5 | ±3 | V | |
–5S | 0.78 | ±0.5 | ±2.5 | ±3 | V | |||
–1V, –2V, –2E, –3V, –4S | 0.8 | ±0.5 | ±2.5 | ±3 | V | |||
VCCEHT_GTS[L1,R4][A, B, C] 53 | Transceiver PMA, transceiver PLL, and transceiver reference clock high voltage analog power supply | — | 1.8 | ±0.5 | ±2.0 | ±2.5 | V | |
VCCERT_GTS[L1, R4][A, B, C] | Transceiver PMA and transceiver reference clock low voltage analog power supply | — | 1 | ±0.5 | ±2.0 | ±2.5 | V |
50 For scope measurement, 20 MHz bandwidth is sufficient. During measurement, put the ground pin as close to the power rail pin as possible.
51 HF noise requires AC 30 mVpp above 1 MHz.
52 For scope measurement, 20 MHz bandwidth is sufficient. During measurement, put the ground pin as close to the power rail pin as possible.
53 HF noise requires AC 30 mVpp above 1 MHz.