PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

Download PDF
ID 683716
Date 7/15/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the PHY Lite for Parallel Interfaces IP 2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices 3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices 4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices 5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices 6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices 7. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives 8. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide
1. About the PHY Lite for Parallel Interfaces IP x
1.1. Device Family Support 1.2. Features
2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices x
2.1. Release Information 2.2. Functional Description 2.3. Getting Started 2.4. I/O Standards 2.5. Design Example
2.2. Functional Description x
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices Top Level Interfaces 2.2.2. Dynamic Reconfiguration
2.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices Top Level Interfaces x
2.2.1.1. Clocks 2.2.1.2. Output Path 2.2.1.3. Input Path
2.2.2. Dynamic Reconfiguration x
2.2.2.1. Calibration IP 2.2.2.2. Dynamic Reconfigurable Delays 2.2.2.3. Register Map
2.3. Getting Started x
2.3.1. Parameter Settings 2.3.2. Signals
2.3.2. Signals x
2.3.2.1. Clock and Reset Interface Signals 2.3.2.2. Output Path Signals 2.3.2.3. Input Path Signals
2.4. I/O Standards x
2.4.1. Design Guidelines
2.4.1. Design Guidelines x
2.4.1.1. DQS Trees 2.4.1.2. Pin Placement Restrictions 2.4.1.3. Maximum Number of DQ Data Pin Configurations
2.4.1.3. Maximum Number of DQ Data Pin Configurations x
2.4.1.3.1. Automatic and Manual Pin Placement 2.4.1.3.2. Single-Ended Pin Configurations 2.4.1.3.3. Differential Pin Configurations 2.4.1.3.4. Mixed Pin Configurations
2.5. Design Example x
2.5.1. Generate the Design Example 2.5.2. Verify Simulation Design Examples using Tester IP
2.5.1. Generate the Design Example x
2.5.1.1. Design Example without Dynamic Reconfiguration 2.5.1.2. Design Example with Dynamic Reconfiguration
2.5.1.1. Design Example without Dynamic Reconfiguration x
2.5.1.1.1. Generate the Synthesis Design Example without Dynamic Reconfiguration 2.5.1.1.2. Generate the Simulation Design Example Without Dynamic Reconfiguration 2.5.1.1.3. Run the Simulation Design Example Without Dynamic Reconfiguration
2.5.1.2. Design Example with Dynamic Reconfiguration x
2.5.1.2.1. Generate the Synthesis Design Example With Dynamic Reconfiguration 2.5.1.2.2. Generate the Simulation Design Example with Dynamic Reconfiguration 2.5.1.2.3. Run the Simulation Design Example Without Dynamic Reconfiguration
2.5.2. Verify Simulation Design Examples using Tester IP x
2.5.2.1. PHY Lite Interface 2.5.2.2. I/O Model 2.5.2.3. IOSSM Tester 2.5.2.4. Write Test 2.5.2.5. Read Test 2.5.2.6. Calbus Test
3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices x
3.1. Release Information 3.2. Functional Description 3.3. Getting Started 3.4. I/O Standards 3.5. Design Example
3.2. Functional Description x
3.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices Top Level Interfaces 3.2.2. Dynamic Reconfiguration 3.2.3. I/O Timing
3.2.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices Top Level Interfaces x
3.2.1.1. Clocks 3.2.1.2. Output Path 3.2.1.3. Input Path
3.2.1.1. Clocks x
3.2.1.1.1. Clock Frequency Relationships
3.2.2. Dynamic Reconfiguration x
3.2.2.1. Calibration IP 3.2.2.2. Dynamic Reconfigurable Delays 3.2.2.3. Register Map
3.3. Getting Started x
3.3.1. Parameter Settings 3.3.2. Signals
3.3.2. Signals x
3.3.2.1. Clock and Reset Interface Signals 3.3.2.2. Output Path Signals 3.3.2.3. Input Path Signals
3.4. I/O Standards x
3.4.1. Design Guidelines
3.4.1. Design Guidelines x
3.4.1.1. DQS Trees 3.4.1.2. Pin Placement Restrictions
3.5. Design Example x
3.5.1. Generating the Design Example 3.5.2. Verifying Simulation Design Examples using Tester IP
3.5.1. Generating the Design Example x
3.5.1.1. Design Example without Dynamic Reconfiguration 3.5.1.2. Dynamic Reconfiguration Design Examples
3.5.1.1. Design Example without Dynamic Reconfiguration x
3.5.1.1.1. Generating the Synthesis Design Example 3.5.1.1.2. Generating the Simulation Design Example
3.5.1.2. Dynamic Reconfiguration Design Examples x
3.5.1.2.1. Generating the Synthesis Design Example 3.5.1.2.2. Generating the Simulation Design Example
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices x
4.1. Release Information 4.2. Functional Description 4.3. Getting Started 4.4. I/O Standards 4.5. Design Guidelines 4.6. Design Example
4.2. Functional Description x
4.2.1. Agilex™ 7 F-Series and I-Series I/O Sub-bank Interconnects 4.2.2. Agilex™ 7 F-Series and I-Series Input DQS/Strobe Tree 4.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices Top Level Interfaces 4.2.4. Dynamic Reconfiguration 4.2.5. I/O Timing
4.2.3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices Top Level Interfaces x
4.2.3.1. Clocks 4.2.3.2. Output Path 4.2.3.3. Input Path
4.2.3.1. Clocks x
4.2.3.1.1. Clock Frequency Relationships
4.2.4. Dynamic Reconfiguration x
4.2.4.1. Connectivity 4.2.4.2. Reconfiguration Features and Register Addressing 4.2.4.3. Dynamic Reconfiguration Guidelines
4.2.4.2. Reconfiguration Features and Register Addressing x
4.2.4.2.1. Control Registers Addresses 4.2.4.2.2. Control Registers
4.2.4.3. Dynamic Reconfiguration Guidelines x
4.2.4.3.1. Strobe Enable Window Calibration 4.2.4.3.2. Output and Strobe Enable Minimum and Maximum Phase Settings 4.2.4.3.3. Input DQ/DQS Delay Chains Maximum Values
4.3. Getting Started x
4.3.1. Parameter Settings 4.3.2. Signals
4.3.1. Parameter Settings x
4.3.1.1. Read Latency 4.3.1.2. Write Latency
4.3.2. Signals x
4.3.2.1. Clock and Reset Interface Signals 4.3.2.2. Output Path Signals 4.3.2.3. Input Path Signals
4.4. I/O Standards x
4.4.1. Input Buffer Reference Voltage (VREF) 4.4.2. On-Chip Termination (OCT)
4.4.2. On-Chip Termination (OCT) x
4.4.2.1. RZQ_GROUP Assignment
4.5. Design Guidelines x
4.5.1. Guidelines: Group Pin Placement 4.5.2. Reference Clock 4.5.3. Reset
4.6. Design Example x
4.6.1. Generating the Design Example
4.6.1. Generating the Design Example x
4.6.1.1. Design Example without Dynamic Reconfiguration 4.6.1.2. Dynamic Reconfiguration Design Examples
4.6.1.1. Design Example without Dynamic Reconfiguration x
4.6.1.1.1. Generating the Synthesis Design Example 4.6.1.1.2. Generating the Simulation Design Example
4.6.1.2. Dynamic Reconfiguration Design Examples x
4.6.1.2.1. Generating the Synthesis Design Example 4.6.1.2.2. Generating the Simulation Design Example
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices x
5.1. Release Information 5.2. Functional Description 5.3. Getting Started 5.4. I/O Standards 5.5. Design Guidelines 5.6. Design Example
5.2. Functional Description x
5.2.1. Top Level Interfaces 5.2.2. Clocks 5.2.3. Output Path 5.2.4. Input Path 5.2.5. Dynamic Reconfiguration
5.2.2. Clocks x
5.2.2.1. Clock Frequency Relationships
5.2.3. Output Path x
5.2.3.1. Output Path Data Alignment
5.2.4. Input Path x
5.2.4.1. Input Path Data Alignment
5.2.5. Dynamic Reconfiguration x
5.2.5.1. RTL Connectivity 5.2.5.2. Address Lookup 5.2.5.3. Reconfiguration Features and Register Addressing 5.2.5.4. Calibration Guidelines
5.2.5.1. RTL Connectivity x
5.2.5.1.1. Daisy Chain
5.2.5.2. Address Lookup x
5.2.5.2.1. Strobes 5.2.5.2.2. Parameter Table Examples
5.2.5.3. Reconfiguration Features and Register Addressing x
5.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices Control Registers Addresses 5.2.5.3.2. Control Registers Description
5.2.5.4. Calibration Guidelines x
5.2.5.4.1. Strobe Enable Window Calibration 5.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
5.3. Getting Started x
5.3.1. Parameter Settings 5.3.2. Signals
5.3.1. Parameter Settings x
5.3.1.1. Read Latency 5.3.1.2. Write Latency
5.3.2. Signals x
5.3.2.1. Clock and Reset Interface Signals 5.3.2.2. Output Path Signals 5.3.2.3. Input Path Signals 5.3.2.4. Avalon Configuration Bus Interface Signals 5.3.2.5. Termination Signals
5.4. I/O Standards x
5.4.1. Input Buffer Reference Voltage (VREF) 5.4.2. On-Chip Termination (OCT)
5.4.1. Input Buffer Reference Voltage (VREF) x
5.4.1.1. Calibrated VREF Settings
5.4.2. On-Chip Termination (OCT) x
5.4.2.1. RZQ_GROUP Assignment 5.4.2.2. Manual Insertion of OCT Block
5.5. Design Guidelines x
5.5.1. Guidelines: Group Pin Placement 5.5.2. Reference Clock 5.5.3. Reset 5.5.4. Constraining Multiple PHY Lite for Parallel Interfaces Intel® FPGA IP to One I/O Bank 5.5.5. Dynamic Reconfiguration 5.5.6. Timing
5.5.6. Timing x
5.5.6.1. Timing Components 5.5.6.2. Timing Constraints and Files 5.5.6.3. Timing Analysis 5.5.6.4. Timing Closure Guidelines
5.5.6.2. Timing Constraints and Files x
5.5.6.2.1. <variation_name>.sdc 5.5.6.2.2. <variation_name>_parameter.tcl 5.5.6.2.3. <variation_name>_ip_parameters.tcl 5.5.6.2.4. <variation_name>_pin_map.tcl 5.5.6.2.5. <variation_name>_report_timing.tcl 5.5.6.2.6. <variation_name>_report_timing_core.tcl
5.5.6.4. Timing Closure Guidelines x
5.5.6.4.1. Timing Closure: Dynamic Reconfiguration 5.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 5.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 5.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 5.5.6.4.5. I/O Timing Violation 5.5.6.4.6. Internal FPGA Path Timing Violation
5.6. Design Example x
5.6.1. Generating the Design Example
5.6.1. Generating the Design Example x
5.6.1.1. Design Example without Dynamic Reconfiguration 5.6.1.2. Dynamic Reconfiguration Design Examples
5.6.1.1. Design Example without Dynamic Reconfiguration x
5.6.1.1.1. Generating the Hardware Design Example 5.6.1.1.2. Generating the Simulation Design Example
5.6.1.2. Dynamic Reconfiguration Design Examples x
5.6.1.2.1. Dynamic Reconfiguration Using Finite State Machine
6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices x
6.1. Release Information 6.2. Functional Description 6.3. Getting Started 6.4. I/O Standards 6.5. Design Guidelines 6.6. Design Example 6.7. Application Specific Design Example
6.2. Functional Description x
6.2.1. Top Level Interfaces 6.2.2. Clocks 6.2.3. Output Path 6.2.4. Input Path 6.2.5. Dynamic Reconfiguration
6.2.2. Clocks x
6.2.2.1. Clock Frequency Relationships
6.2.3. Output Path x
6.2.3.1. Output Path Data Alignment
6.2.4. Input Path x
6.2.4.1. Input Path Data Alignment
6.2.5. Dynamic Reconfiguration x
6.2.5.1. RTL Connectivity 6.2.5.2. Address Lookup 6.2.5.3. Reconfiguration Features and Register Addressing 6.2.5.4. Calibration Guidelines
6.2.5.1. RTL Connectivity x
6.2.5.1.1. Daisy Chain
6.2.5.2. Address Lookup x
6.2.5.2.1. Strobes 6.2.5.2.2. Parameter Table Examples
6.2.5.3. Reconfiguration Features and Register Addressing x
6.2.5.3.1. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Address Registers 6.2.5.3.2. Control Registers Description
6.2.5.4. Calibration Guidelines x
6.2.5.4.1. Strobe Enable Window Calibration 6.2.5.4.2. Output and Strobe Enable Minimum and Maximum Phase Settings
6.3. Getting Started x
6.3.1. Parameter Settings 6.3.2. Signals
6.3.1. Parameter Settings x
6.3.1.1. Read Latency 6.3.1.2. Write Latency
6.3.2. Signals x
6.3.2.1. Clock and Reset Interface Signals 6.3.2.2. Output Path Signals 6.3.2.3. Input Path Signals 6.3.2.4. Avalon Configuration Bus Interface Signals 6.3.2.5. Termination Signals
6.4. I/O Standards x
6.4.1. Input Buffer Reference Voltage (VREF) 6.4.2. On-Chip Termination (OCT)
6.4.1. Input Buffer Reference Voltage (VREF) x
6.4.1.1. Calibrated VREF Settings
6.4.2. On-Chip Termination (OCT) x
6.4.2.1. RZQ_GROUP Assignment 6.4.2.2. Manual Insertion of OCT Block
6.5. Design Guidelines x
6.5.1. Guidelines: Group Pin Placement 6.5.2. Reference Clock 6.5.3. Reset 6.5.4. Constraining Multiple PHY Lite for Parallel Interfaces to One I/O Bank 6.5.5. Dynamic Reconfiguration 6.5.6. Timing
6.5.6. Timing x
6.5.6.1. Timing Components 6.5.6.2. Timing Constraints and Files 6.5.6.3. Timing Analysis 6.5.6.4. Timing Closure Guidelines
6.5.6.2. Timing Constraints and Files x
6.5.6.2.1. <variation_name>.sdc 6.5.6.2.2. <variation_name>_parameter.tcl 6.5.6.2.3. <variation_name>_ip_parameters.tcl 6.5.6.2.4. <variation_name>_pin_map.tcl 6.5.6.2.5. <variation_name>_report_timing.tcl 6.5.6.2.6. <variation_name>_report_timing_core.tcl
6.5.6.4. Timing Closure Guidelines x
6.5.6.4.1. Timing Closure: Dynamic Reconfiguration 6.5.6.4.2. Timing Closure: Input Strobe Setup and Hold Delay Constraints 6.5.6.4.3. Timing Closure: Output Strobe Setup and Hold Delay Constraints 6.5.6.4.4. Timing Closure: Non Edge-Aligned Input Data 6.5.6.4.5. I/O Timing Violation 6.5.6.4.6. Internal FPGA Path Timing Violation
6.6. Design Example x
6.6.1. Generating the Design Example
6.6.1. Generating the Design Example x
6.6.1.1. Design Example without Dynamic Reconfiguration 6.6.1.2. Dynamic Reconfiguration Design Examples
6.6.1.1. Design Example without Dynamic Reconfiguration x
6.6.1.1.1. Generating the Hardware Design Example 6.6.1.1.2. Generating the Simulation Design Example
6.6.1.2. Dynamic Reconfiguration Design Examples x
6.6.1.2.1. Dynamic Reconfiguration with Debug Kit 6.6.1.2.2. Dynamic Reconfiguration Using Finite State Machine
6.7. Application Specific Design Example x
6.7.1. Implementation using the PHY Lite for Parallel Interfaces Intel® FPGA IP
1. About the PHY Lite for Parallel Interfaces IP
2. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 5 E-Series Devices
3. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 M-Series Devices
4. PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices
5. PHY Lite for Parallel Interfaces Intel® FPGA IP for Stratix® 10 Devices
6. PHY Lite for Parallel Interfaces Intel® FPGA IP for Arria® 10 and Cyclone® 10 GX Devices
7. PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide Document Archives
8. Document Revision History for the PHY Lite for Parallel Interfaces Intel® FPGA IP User Guide

4.2.3.1. Clocks

The PHY Lite for Parallel Interfaces Intel® FPGA IP sources a reference clock from a dedicated clock pin to the PLL inside the IP. This PLL provides four clock domains for the output and input paths.

Table 59.   PHY Lite for Parallel Interfaces Intel® FPGA IP Clock Domains
Clock Domain Description
Core clock The IP generates this clock internally and uses it for all transfers between the FPGA core fabric and I/O banks. The clock phase alignment (CPA) circuitry keeps the clock in phase with the PHY clock for transfers between the core and the periphery.
PHY clock The IP uses this clock internally for PHY circuitry running at the same frequency as the core clock.
VCO clock The PLL generates this clock internally. The input and output paths use the VCO clock to generate interpolator delays that compensates for PVT variations.
Interface clock This is the clock frequency of the external device connected to the FPGA I/Os.
Table 60.  Interface Frequencies Supported by the PHY Lite for Parallel Interfaces Intel® FPGA IP for Agilex™ 7 F-Series and I-Series Devices
Core Clock Rate Speed Grade –1 (MHz) Speed Grade –2 (MHz) Speed Grade –3 (MHz)
Min Max Min Max Min Max
Quarter 100 1,200 100 933 100 933
Half 100 800 100 666 100 600
Full 100 400 100 333 100 300

Section Content
Clock Frequency Relationships

Level Two Title