Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide

Download PDF
ID 814550
Date 5/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash U10 with Default Factory Image 3.3.2. Restoring Board QSPI Flash U4 with the Default Factory Image
4. Board Test System x
4.1. Setting Up BTS GUI Running Environment 4.2. Troubleshooting for Launching BTS 4.3. BTS Functionalities
4.1. Setting Up BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing Quartus® Prime Software 4.1.5. Running the BTS GUI
4.3. BTS Functionalities x
4.3.1. Diagnostic GUI 4.3.2. Clock Controller GUI 4.3.3. Power Monitor GUI 4.3.4. MAX® 10 Controller GUI 4.3.5. Agilex™ 5 FPGA E-Series Test Functionality 4.3.6. Information Display
4.3.2. Clock Controller GUI x
4.3.2.1. Si5332 Clock 4.3.2.2. Si5518 Clock
4.3.3. Power Monitor GUI x
4.3.3.1. Power Monitor 4.3.3.2. Temperature Monitor
4.3.4. MAX® 10 Controller GUI x
4.3.4.1. Remote I/O Control 4.3.4.2. Expansion Board Control 4.3.4.3. System Control
4.3.4.1. Remote I/O Control x
4.3.4.1.1. Remote Control 4.3.4.1.2. MISC LED Control
4.3.4.1.1. Remote Control x
4.3.4.1.1.1. Push Button 4.3.4.1.1.2. User Switch 4.3.4.1.1.3. MSEL 4.3.4.1.1.4. Si569-1V8
4.3.5. Agilex™ 5 FPGA E-Series Test Functionality x
4.3.5.1. DDR4 Test 4.3.5.2. HPS DDR4 Test 4.3.5.3. LPDDR4 Test 4.3.5.4. QSFP Test 4.3.5.5. SFP+ Test 4.3.5.6. FMC+ Test 4.3.5.7. SMA Test
4.3.6. Information Display x
4.3.6.1. Sys Info 4.3.6.2. Connection 4.3.6.3. The Bottom Status Bar
5. Development Kit Hardware and Configuration x
5.1. Configuring the FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring the FPGA Device by Active Serial (AS) Modes (Default Mode) 5.3. Configuring the FPGA Device by Avalon® Streaming Modes 5.4. Expansion Boards
5.4. Expansion Boards x
5.4.1. HPS Expansion Board (HPS-EB) 5.4.2. HPS NAND Board (HPS-NB) 5.4.3. HPS Test Board (HPS-TB)
6. Custom Projects for the Development Kit x
6.1. Golden Top
A. Development Kit Components x
A.1. Board Overview A.2. System Management A.3. Power A.4. Clocks A.5. General Input/Output A.6. Input and Output Components A.7. Memory Interfaces A.8. Communication Interfaces A.9. Expansion Boards A.10. Connectors and Headers
A.2. System Management x
A.2.1. JTAG Master Sources
A.6. Input and Output Components x
A.6.1. Push Buttons A.6.2. Switches A.6.3. LEDs
A.8. Communication Interfaces x
A.8.1. QSFP+ A.8.2. SFP+ A.8.3. Ethernet A.8.4. FMC A.8.5. MIPI A.8.6. USB3.1 A.8.7. HPS IO48 Interface A.8.8. Serial Buses
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide
A. Development Kit Components
B. Additional Information

4.1.5. Running the BTS GUI

With the power to the board off, follow these steps.
  1. Connect the micro-USB cable to your PC and the board.
  2. Check the development board switches and jumpers are set according to your preferences. Refer to the Development Kit Setup section.
  3. Check the external modules status: SFP+/QSFP/FMC+/SMA.
  4. Turn on the board power switch. Wait for all LEDs blink one time and LED D13 turns green.
  5. Click start.bat in the package to open the GUI.
    Note: To ensure operating stability, keep the micro-USB cable connected and the board powered on when running the demonstration application.

Navigate to the <packagedir>\examples\board_test_system directory to run BTS. The BTS release folder always includes the following files, as shown in the figure below.

Figure 4. BTS Package Folder
Figure 5. Windows Console of BTS Launching
Figure 6. Linux Console of BTS Launching
Note: The .bat or shell script checks the Java environment settings, copies necessary files, and gives some prompts if the environment is not set up correctly.
Level Two Title