Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide

Download PDF
ID 814550
Date 5/24/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash U10 with Default Factory Image 3.3.2. Restoring Board QSPI Flash U4 with the Default Factory Image
4. Board Test System x
4.1. Setting Up BTS GUI Running Environment 4.2. Troubleshooting for Launching BTS 4.3. BTS Functionalities
4.1. Setting Up BTS GUI Running Environment x
4.1.1. Downloading OpenJDK 4.1.2. Downloading OpenJFX 4.1.3. Installing OpenJDK and OpenJFX 4.1.4. Installing Quartus® Prime Software 4.1.5. Running the BTS GUI
4.3. BTS Functionalities x
4.3.1. Diagnostic GUI 4.3.2. Clock Controller GUI 4.3.3. Power Monitor GUI 4.3.4. MAX® 10 Controller GUI 4.3.5. Agilex™ 5 FPGA E-Series Test Functionality 4.3.6. Information Display
4.3.2. Clock Controller GUI x
4.3.2.1. Si5332 Clock 4.3.2.2. Si5518 Clock
4.3.3. Power Monitor GUI x
4.3.3.1. Power Monitor 4.3.3.2. Temperature Monitor
4.3.4. MAX® 10 Controller GUI x
4.3.4.1. Remote I/O Control 4.3.4.2. Expansion Board Control 4.3.4.3. System Control
4.3.4.1. Remote I/O Control x
4.3.4.1.1. Remote Control 4.3.4.1.2. MISC LED Control
4.3.4.1.1. Remote Control x
4.3.4.1.1.1. Push Button 4.3.4.1.1.2. User Switch 4.3.4.1.1.3. MSEL 4.3.4.1.1.4. Si569-1V8
4.3.5. Agilex™ 5 FPGA E-Series Test Functionality x
4.3.5.1. DDR4 Test 4.3.5.2. HPS DDR4 Test 4.3.5.3. LPDDR4 Test 4.3.5.4. QSFP Test 4.3.5.5. SFP+ Test 4.3.5.6. FMC+ Test 4.3.5.7. SMA Test
4.3.6. Information Display x
4.3.6.1. Sys Info 4.3.6.2. Connection 4.3.6.3. The Bottom Status Bar
5. Development Kit Hardware and Configuration x
5.1. Configuring the FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring the FPGA Device by Active Serial (AS) Modes (Default Mode) 5.3. Configuring the FPGA Device by Avalon® Streaming Modes 5.4. Expansion Boards
5.4. Expansion Boards x
5.4.1. HPS Expansion Board (HPS-EB) 5.4.2. HPS NAND Board (HPS-NB) 5.4.3. HPS Test Board (HPS-TB)
6. Custom Projects for the Development Kit x
6.1. Golden Top
A. Development Kit Components x
A.1. Board Overview A.2. System Management A.3. Power A.4. Clocks A.5. General Input/Output A.6. Input and Output Components A.7. Memory Interfaces A.8. Communication Interfaces A.9. Expansion Boards A.10. Connectors and Headers
A.2. System Management x
A.2.1. JTAG Master Sources
A.6. Input and Output Components x
A.6.1. Push Buttons A.6.2. Switches A.6.3. LEDs
A.8. Communication Interfaces x
A.8.1. QSFP+ A.8.2. SFP+ A.8.3. Ethernet A.8.4. FMC A.8.5. MIPI A.8.6. USB3.1 A.8.7. HPS IO48 Interface A.8.8. Serial Buses
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Premium Development Kit User Guide
A. Development Kit Components
B. Additional Information

4.1.4. Installing Quartus® Prime Software

You must install the Quartus® Prime software to support the silicon on the development kit. The recommended version is located in the README.txt file in the examples\board_test_system directory.

The BTS communicates over JTAG to a test design running in the FPGA. The BTS shares the JTAG with other applications such as the Nios® II JTAG Debug Module and the Signal Tap logic analyzer. Altera recommends closing other applications before using BTS, as the GUI is designed based on the Quartus® Prime software.

The BTS relies on the Quartus® Prime software's specific library. Before running the BTS, open the Quartus® Prime software to automatically set the environment variable QUARTUS_ROOTDIR. You can also change it through Window's Environment Variables in System Properties. The BTS uses this environment variable to locate the Quartus® Prime library.

Level Two Title