Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

Download PDF
ID 813652
Date 7/22/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the Low Latency 40G Ethernet Intel® FPGA IP 2. Low Latency 40G Ethernet Intel® FPGA IP Parameters 3. Getting Started 4. Functional Description 5. Clocking and Reset Requirements 6. Interfaces and Signal Descriptions 7. Control, Status, and Statistics Register Descriptions 8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs 9. Document Revision History for Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs
1. About the Low Latency 40G Ethernet Intel® FPGA IP x
1.1. Low Latency 40G Ethernet Intel® FPGA IP Supported Features 1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support 1.3. Resource Utilization 1.4. Release Information
1.2. Low Latency 40G Ethernet Intel® FPGA IP Device Family and Speed Grade Support x
1.2.1. Low Latency 40G Ethernet Intel® FPGA IP Device Family Support 1.2.2. Low Latency 40G Ethernet Intel® FPGA IP Device Speed Grade Support
3. Getting Started x
3.1. Introduction to Intel® FPGA IP 3.2. Installing and Licensing Intel® FPGA IPs 3.3. Specifying the IP Parameters and Options 3.4. Simulating the IP 3.5. Generated File Structure 3.6. Integrating Your IP in Your Design 3.7. Testbench 3.8. Compiling the Full Design and Programming the FPGA
3.6. Integrating Your IP in Your Design x
3.6.1. Pin Assignments 3.6.2. Placement Settings
3.7. Testbench x
3.7.1. Understanding the Testbench Behavior
4. Functional Description x
4.1. Low Latency 40G Ethernet Intel® FPGA IP Functional Description 4.2. GTS Transceiver Configuration 4.3. TX MAC Datapath 4.4. RX MAC Datapath 4.5. Flow Control 4.6. Frame Status Checking 4.7. Link Fault Signaling Interface
4.3. TX MAC Datapath x
4.3.1. Preamble Pass-through/Insertion 4.3.2. Padding Bytes Insertion 4.3.3. Deficit Idle Count 4.3.4. TX CRC Insertion/Passthrough 4.3.5. TX Avalon® Streaming Filter 4.3.6. TX PCS 4.3.7. PMA
4.4. RX MAC Datapath x
4.4.1. RX Preamble Pass-through or Removal 4.4.2. RX CRC Checking and Dynamic Option to Forward 4.4.3. Strict SFD/Preamble Checking 4.4.4. RX PCS Functional Description
4.5. Flow Control x
4.5.1. TX Pause/PFC Flow Control Transmission 4.5.2. XON/XOFF Pause Frames
4.6. Frame Status Checking x
4.6.1. Frame Type Checking 4.6.2. Length Checking
5. Clocking and Reset Requirements x
5.1. Reset Requirements
6. Interfaces and Signal Descriptions x
6.1. TX MAC Interface to User Logic 6.2. RX MAC Interface to User Logic 6.3. GTS Transceivers Signals 6.4. GTS Transceiver Reconfiguration Signals 6.5. Avalon® Memory-Mapped Management Interface 6.6. Miscellaneous Status and Debug Signals 6.7. Reset Signals 6.8. Clocks 6.9. Flow Control Interface 6.10. GTS Reset Sequencer Intel® FPGA IP
7. Control, Status, and Statistics Register Descriptions x
7.1. PHY Registers 7.2. TX MAC Registers 7.3. RX MAC Registers 7.4. Pause/PFC Flow Control 7.5. Statistics Counters 7.6. Shadow Register
1. About the Low Latency 40G Ethernet Intel® FPGA IP
2. Low Latency 40G Ethernet Intel® FPGA IP Parameters
3. Getting Started
4. Functional Description
5. Clocking and Reset Requirements
6. Interfaces and Signal Descriptions
7. Control, Status, and Statistics Register Descriptions
8. Comparison Between Various Low Latency 40G Ethernet Intel® FPGA IPs
9. Document Revision History for Low Latency 40G Ethernet Intel® FPGA IP User Guide: Agilex™ 5 FPGAs and SoCs

6.5. Avalon® Memory-Mapped Management Interface

Table 20.   Avalon® Memory-Mapped Management Interface Signals

Signal

Direction

Width

Description

clk_status Input 1 The clock that drives the control and status registers.
status_addr Input 16

Register address.
status_read Input 1

When asserted, specifies a read request.

status_write Input 1 When asserted, specifies a write request.
status_readdata Output 32 Drives read data.
status_readdata_valid Output 1 Register read data valid.
status_writedata Input 32 Drives the write data.
status_waitrequest Output 1 Wait request. Indicates that the device is not ready to complete the transaction. The status_waitrequest signal is only used for read transactions. Refer to the Avalon® Interface Specifications for more details.
Related Information
Level Two Title