F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

Download PDF
ID 720985
Date 4/01/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide 2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. Low Latency Ethernet 10G MAC Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers 8. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Low Latency Ethernet 10G MAC Operating Modes 2.4. Device Family Support 2.5. Performance and Resource Utilization
2.5. Performance and Resource Utilization x
2.5.1. Resource Utilization 2.5.2. TX and RX Latency
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Specifying the IP Core Parameters and Options ( Intel® Quartus® Prime Pro Edition) 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IP Cores 3.6. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 3.7. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Examples
3.6. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core x
3.6.1. Designing Considerations for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP
3.6.1. Designing Considerations for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP x
3.6.1.1. Timing Constraints
3.6.1.1. Timing Constraints x
3.6.1.1.1. Pseudo-Static CSR Fields 3.6.1.1.2. Clock Crosser 3.6.1.1.3. Dual Clock FIFO
3.7. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Examples x
3.7.1. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example for Intel® Agilex™ Devices
4. Functional Description x
4.1. Architecture 4.2. Interfaces 4.3. Frame Types 4.4. TX Datapath 4.5. RX Datapath 4.6. Flow Control 4.7. Reset Requirements 4.8. Supported PHYs 4.9. XGMII Error Handling (Link Fault)
4.4. TX Datapath x
4.4.1. Padding Bytes Insertion 4.4.2. Address Insertion 4.4.3. CRC-32 Insertion 4.4.4. XGMII Encapsulation 4.4.5. Inter-Packet Gap Generation and Insertion 4.4.6. XGMII Transmission 4.4.7. TX Promiscuous (Transparent) Mode 4.4.8. TX Timing Diagrams
4.4.4. XGMII Encapsulation x
4.4.4.1. Transmit Path
4.5. RX Datapath x
4.5.1. XGMII Decapsulation 4.5.2. CRC Checking 4.5.3. Address Checking 4.5.4. Frame Type Checking 4.5.5. CRC and Padding Bytes Removal 4.5.6. Frame Length Checking 4.5.7. Overflow Handling 4.5.8. RX Promiscuous (Transparent) Mode 4.5.9. RX Timing Diagrams
4.5.3. Address Checking x
4.5.3.1. Unicast Frame Filtering 4.5.3.2. Multicast Frame Filtering
4.5.4. Frame Type Checking x
4.5.4.1. Malformed RX Packets 4.5.4.2. CRC Error 4.5.4.3. Address Check Error
4.5.6. Frame Length Checking x
4.5.6.1. Frame Length 4.5.6.2. Payload Length
4.6. Flow Control x
4.6.1. IEEE 802.3 Flow Control
4.6.1. IEEE 802.3 Flow Control x
4.6.1.1. Pause Frame Reception 4.6.1.2. Pause Frame Transmission
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Speed Selection Signal 6.3. Error Correction Signals 6.4. Avalon® Memory-Mapped Interface Programming Signals 6.5. Avalon® Streaming Data Interfaces 6.6. Avalon® Streaming Flow Control Signals 6.7. Avalon® Streaming Status Interface 6.8. PHY-side Interfaces
6.5. Avalon® Streaming Data Interfaces x
6.5.1. Avalon® Streaming TX Data Interface Signals 6.5.2. Avalon® Streaming RX Data Interface Signals 6.5.3. Avalon® Streaming Data Interface Clocks
6.7. Avalon® Streaming Status Interface x
6.7.1. Avalon® Streaming Interface TX Status Signals 6.7.2. Avalon® Streaming Interface RX Status Signals
6.8. PHY-side Interfaces x
6.8.1. XGMII TX Signals 6.8.2. XGMII RX Signals
7. Configuration Registers x
7.1. Register Map 7.2. Register Access Definition 7.3. Primary MAC Address 7.4. TX Configuration and Status Registers 7.5. Flow Control Registers 7.6. RX Configuration and Status Registers 7.7. ECC Registers 7.8. Statistics Registers
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. Low Latency Ethernet 10G MAC Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
8. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

3.5. Simulating Intel® FPGA IP Cores

The Intel® Quartus® Prime software supports IP core RTL simulation in specific EDA simulators. IP generation optionally creates simulation files, including the functional simulation model, any testbench (or example design), and vendor-specific simulator setup scripts for each IP core. You can use the functional simulation model and any testbench or example design for simulation. IP generation output may also include scripts to compile and run any testbench. The scripts list all models or libraries you require to simulate your IP core.

The Intel® Quartus® Prime software provides integration with many simulators and supports multiple simulation flows, including your own scripted and custom simulation flows. Whichever flow you choose, IP core simulation involves the following steps:

  1. Generate IP HDL, testbench (or example design), and simulator setup script files.
  2. Set up your simulator environment and any simulation scripts.
  3. Compile simulation model libraries.
  4. Run your simulator.
Level Two Title