F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

Download PDF
ID 720985
Date 4/01/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide 2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview 3. Getting Started 4. Functional Description 5. Low Latency Ethernet 10G MAC Intel® FPGA IP Parameters 6. Interface Signals 7. Configuration Registers 8. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview x
2.1. Release Information 2.2. Features 2.3. Low Latency Ethernet 10G MAC Operating Modes 2.4. Device Family Support 2.5. Performance and Resource Utilization
2.5. Performance and Resource Utilization x
2.5.1. Resource Utilization 2.5.2. TX and RX Latency
3. Getting Started x
3.1. Introduction to Intel® FPGA IP Cores 3.2. Installing and Licensing Intel® FPGA IP Cores 3.3. Specifying the IP Core Parameters and Options ( Intel® Quartus® Prime Pro Edition) 3.4. Generated File Structure 3.5. Simulating Intel® FPGA IP Cores 3.6. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core 3.7. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Examples
3.6. Upgrading the Low Latency Ethernet 10G MAC Intel® FPGA IP Core x
3.6.1. Designing Considerations for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP
3.6.1. Designing Considerations for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP x
3.6.1.1. Timing Constraints
3.6.1.1. Timing Constraints x
3.6.1.1.1. Pseudo-Static CSR Fields 3.6.1.1.2. Clock Crosser 3.6.1.1.3. Dual Clock FIFO
3.7. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Examples x
3.7.1. Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example for Intel® Agilex™ Devices
4. Functional Description x
4.1. Architecture 4.2. Interfaces 4.3. Frame Types 4.4. TX Datapath 4.5. RX Datapath 4.6. Flow Control 4.7. Reset Requirements 4.8. Supported PHYs 4.9. XGMII Error Handling (Link Fault)
4.4. TX Datapath x
4.4.1. Padding Bytes Insertion 4.4.2. Address Insertion 4.4.3. CRC-32 Insertion 4.4.4. XGMII Encapsulation 4.4.5. Inter-Packet Gap Generation and Insertion 4.4.6. XGMII Transmission 4.4.7. TX Promiscuous (Transparent) Mode 4.4.8. TX Timing Diagrams
4.4.4. XGMII Encapsulation x
4.4.4.1. Transmit Path
4.5. RX Datapath x
4.5.1. XGMII Decapsulation 4.5.2. CRC Checking 4.5.3. Address Checking 4.5.4. Frame Type Checking 4.5.5. CRC and Padding Bytes Removal 4.5.6. Frame Length Checking 4.5.7. Overflow Handling 4.5.8. RX Promiscuous (Transparent) Mode 4.5.9. RX Timing Diagrams
4.5.3. Address Checking x
4.5.3.1. Unicast Frame Filtering 4.5.3.2. Multicast Frame Filtering
4.5.4. Frame Type Checking x
4.5.4.1. Malformed RX Packets 4.5.4.2. CRC Error 4.5.4.3. Address Check Error
4.5.6. Frame Length Checking x
4.5.6.1. Frame Length 4.5.6.2. Payload Length
4.6. Flow Control x
4.6.1. IEEE 802.3 Flow Control
4.6.1. IEEE 802.3 Flow Control x
4.6.1.1. Pause Frame Reception 4.6.1.2. Pause Frame Transmission
6. Interface Signals x
6.1. Clock and Reset Signals 6.2. Speed Selection Signal 6.3. Error Correction Signals 6.4. Avalon® Memory-Mapped Interface Programming Signals 6.5. Avalon® Streaming Data Interfaces 6.6. Avalon® Streaming Flow Control Signals 6.7. Avalon® Streaming Status Interface 6.8. PHY-side Interfaces
6.5. Avalon® Streaming Data Interfaces x
6.5.1. Avalon® Streaming TX Data Interface Signals 6.5.2. Avalon® Streaming RX Data Interface Signals 6.5.3. Avalon® Streaming Data Interface Clocks
6.7. Avalon® Streaming Status Interface x
6.7.1. Avalon® Streaming Interface TX Status Signals 6.7.2. Avalon® Streaming Interface RX Status Signals
6.8. PHY-side Interfaces x
6.8.1. XGMII TX Signals 6.8.2. XGMII RX Signals
7. Configuration Registers x
7.1. Register Map 7.2. Register Access Definition 7.3. Primary MAC Address 7.4. TX Configuration and Status Registers 7.5. Flow Control Registers 7.6. RX Configuration and Status Registers 7.7. ECC Registers 7.8. Statistics Registers
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide
2. Low Latency Ethernet 10G MAC Intel® FPGA IP Overview
3. Getting Started
4. Functional Description
5. Low Latency Ethernet 10G MAC Intel® FPGA IP Parameters
6. Interface Signals
7. Configuration Registers
8. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP User Guide

4.5.5. CRC and Padding Bytes Removal

By default, the MAC RX forwards receive frames to the client without removing the CRC field and padding bytes from the frames. You can configure the MAC RX to remove the CRC field by setting the rx_padcrc_control register to 1. To remove both the CRC field and padding bytes, set the rx_padcrc_control register to 3.

When enabled, the MAC RX removes padding bytes from receive frames whose payload length is less than the following values for the different frame types:

  • 46 bytes for basic frames
  • 42 bytes for VLAN tagged frames
  • 38 bytes for stacked VLAN tagged frames

The MAC RX removes padding bytes only when the VLAN and stacked VLAN detection is enabled (rx_vlan_detection[0] = 0). Otherwise, the MAC RX does not remove padding bytes even if padding bytes removal is enabled.

Level Two Title