Symmetric Cryptographic Intel FPGA Hard IP User Guide

Download PDF
ID 714305
Date 10/31/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Cryptographic IP Data Profiles 7. Configuration Registers 8. Design Example 9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives 10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Core Applications
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. AXI-ST Interface 2.4. AXI-Lite Interface
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Symmetric Cryptographic IP Core Flow 4.5. Dynamically Disabling SM4 Capability 4.6. Error Handling 4.7. Error Reporting 4.8. Resetting the IP Core 4.9. Channel Definition and Allocation 4.10. Byte Ordering 4.11. AXI-ST Single Packet Mode 4.12. AXI-ST Multiple Packet Mode
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.6. Error Handling x
4.6.1. Detected Error Handling 4.6.2. Key RAM ECC Error Handling
5. Block Description x
5.1. Reset Sequencer 5.2. AXI-ST Ready Latency 5.3. AXI Adapter 5.4. Integrity Check Value Comparison
5.3. AXI Adapter x
5.3.1. MAC Packing 5.3.2. Data Last Indicator 5.3.3. Stream and Channel ID Buffering 5.3.4. TKEEP and LAST_SEGMENT Signals Generation 5.3.5. MAC Dropping on Decryption
6. Cryptographic IP Data Profiles x
6.1. MAC Security Profile (MACsec) 6.2. IP Security Profile (IPsec) 6.3. Generic GCM Profile (GCM) 6.4. Generic XTS Profile (XTS)
6.1. MAC Security Profile (MACsec) x
6.1.1. MACsec Flow 6.1.2. AXI-ST Interface Using MAC Security (MACsec) Profile Pattern
6.2. IP Security Profile (IPsec) x
6.2.1. AXI-ST Interface Using IP Security (IPsec) Profile Pattern
6.3. Generic GCM Profile (GCM) x
6.3.1. AXI- ST Interface Using Generic GCM Profile Pattern
6.4. Generic XTS Profile (XTS) x
6.4.1. AXI-ST Interface Using Generic XTS Profile Pattern
7. Configuration Registers x
7.1. Cryptographic Primary Control Register 7.2. Cryptographic Secondary Control Register 7.3. Cryptographic Primary Status Register 7.4. Cryptographic Error Status Register 7.5. Cryptographic Error Control Register 7.6. Cryptographic Packet Error Control 1 Register 7.7. Cryptographic Packet Error Control 2 Register 7.8. Cryptographic Error Code Control 1 Register 7.9. Cryptographic Error Code Control 2 Register 7.10. Cryptographic Error Code Internal Control Register 7.11. Cryptographic Internal Error Control Register 7.12. Cryptographic First Error Log Register 7.13. Cryptographic Packet Error Log 1 Register 7.14. Cryptographic Packet Error Log 2 Register 7.15. Cryptographic Internal Error Log Register 7.16. Cryptographic Wall Clock LSB Register 7.17. Cryptographic Wall Clock MSB Register 7.18. Ternary Control Register
8. Design Example x
8.1. Functional Description 8.2. Crypto VSIP Top Block Descriptions 8.3. Test Configurations 8.4. Software Requirements 8.5. Simulation Requirements 8.6. Steps to Generate the Design Example 8.7. Running Simulation Tests 8.8. Running Hardware Tests
8.2. Crypto VSIP Top Block Descriptions x
8.2.1. Clock and Reset 8.2.2. Host Interface
8.7. Running Simulation Tests x
8.7.1. Steps to Simulate the Design Example
8.8. Running Hardware Tests x
8.8.1. Supported Boards 8.8.2. Steps to Compile the Design Example for Hardware 8.8.3. Steps to Run the Design Example on Hardware
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Cryptographic IP Data Profiles
7. Configuration Registers
8. Design Example
9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives
10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide

4.2. Specifying the IP Core Parameters and Options

The IP parameter editor allows you to quickly configure your custom IP variation. Use the following steps to specify IP core options and parameters in the Intel® Quartus® Prime Pro Edition software.

  1. If you do not already have an Intel® Quartus® Prime Pro Edition project in which to integrate your Symmetric Cryptographic Intel® FPGA Hard IP core, you must create one.
    1. In the Intel® Quartus® Prime Pro Edition, click File > New Project Wizard to create a new Quartus Prime project, or File > Open Project to open an existing Quartus Prime project. The wizard prompts you to specify a device.
    2. Specify the device family Intel® Agilex™ and select a device that contains the Symmetric Cryptographic Intel® FPGA Hard IP that meets the speed grade requirements for the IP core.
    3. Click Finish.
  2. In the IP Catalog, locate and select Symmetric Cryptographic Intel® FPGA Hard IP. The New IP Variation window appears.
  3. Specify a top-level name for your new custom IP variation. The parameter editor saves the IP variation settings in a file named <your_ip> .ip.
  4. Click OK. The parameter editor appears.
  5. Specify the parameters for your IP core variation. Refer to IP Parameter settings for information about specific IP core parameters.
  6. Optionally, to generate a simulation testbench or compilation and hardware design example, follow the instructions in the Design Example.
  7. Click Generate HDL. The Generation dialog box appears.
  8. Specify output file generation options, and then click Generate. The IP variation files generate according to your specifications.
  9. Click Finish. The parameter editor adds the top-level .ip file to the current project automatically. If you are prompted to manually add the .ip file to the project, click Project > Add/Remove Files in Project to add the file.
Level Two Title