MAX® 10 FPGA Development Kit User Guide

Download PDF
ID 683460
Date 11/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Board Test System 4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation 2.4. Board Update Portal
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Software 2.3.2. Installing the Development Kit 2.3.3. Installing the Intel® FPGA Download Cable Driver
2.4. Board Update Portal x
2.4.1. Step 1: Connect to the Board Update Portal 2.4.2. Step 2: Update the User Software Portion
3. Board Test System x
3.1. Using the Configure Menu 3.2. The System Info Tab 3.3. The GPIO Tab 3.4. The Flash Tab 3.5. The HSMC Tab 3.6. The DDR3 Tab 3.7. The ADC Tab 3.8. The HDMI Tab 3.9. The Sleep Mode Tab 3.10. The Power Monitor 3.11. The Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Featured Device A.3. Configuration A.4. Status Elements A.5. Setup Elements A.6. General User Input/Output A.7. Clock Circuitry A.8. Components and Interfaces A.9. Memory A.10. Power Distribution System
A.3. Configuration x
A.3.1. Using the Quartus® Prime Programmer A.3.2. Selecting the Internal Configuration Scheme A.3.3. Switch and Jumper Settings
A.7. Clock Circuitry x
A.7.1. On-Board Oscillators A.7.2. Off-Board Clock Input/Output
A.8. Components and Interfaces x
A.8.1. 10/100/1000 Ethernet PHY A.8.2. Digital-to-Analog Converter A.8.3. HDMI Video Output A.8.4. HSMC A.8.5. Pmod Connectors A.8.6. USB to UART
A.9. Memory x
A.9.1. DDR3 Rev. B Board A.9.2. DDR3 Rev. C Board A.9.3. Flash
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Board Test System
4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

2.4.1. Step 1: Connect to the Board Update Portal

  1. Install the Quartus® Prime software. Refer to Installing the Quartus® Prime Software for instructions.
  2. With the board powered down, set the DIP switch SW2.2 to the ON position (factory default), which loads the factory default design from the MAX® 10 FPGA internal flash image 0 on power up.
  3. Attach the Ethernet cable from RJ-45 port A (the bottom one) to your network hub.
  4. Power up the board. The board connects to your network server and obtains an Internet protocol address.
  5. On installation directory of the Quartus® Prime software, click nios2eds > Nios II Command Shell.bat
  6. In the Nios® II command shell, type the following command:
    nios2-terminal.exe
    When the IP address has been assigned, the command shell displays the following information:
  7. Launch a web browser on a computer that is connected to the same network and type the Internet protocol address displayed on the Nios® II command shell. The Board Update Portal web page appears on your PC.
Note: If you cannot connect to the Board Update Portal, refer to the readme.txt file under <package rootdir>\factory_recovery directory on how you can recover the factory build.
Level Two Title