MAX® 10 FPGA Development Kit User Guide

Download PDF
ID 683460
Date 11/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Board Test System 4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation 2.4. Board Update Portal
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Software 2.3.2. Installing the Development Kit 2.3.3. Installing the Intel® FPGA Download Cable Driver
2.4. Board Update Portal x
2.4.1. Step 1: Connect to the Board Update Portal 2.4.2. Step 2: Update the User Software Portion
3. Board Test System x
3.1. Using the Configure Menu 3.2. The System Info Tab 3.3. The GPIO Tab 3.4. The Flash Tab 3.5. The HSMC Tab 3.6. The DDR3 Tab 3.7. The ADC Tab 3.8. The HDMI Tab 3.9. The Sleep Mode Tab 3.10. The Power Monitor 3.11. The Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Featured Device A.3. Configuration A.4. Status Elements A.5. Setup Elements A.6. General User Input/Output A.7. Clock Circuitry A.8. Components and Interfaces A.9. Memory A.10. Power Distribution System
A.3. Configuration x
A.3.1. Using the Quartus® Prime Programmer A.3.2. Selecting the Internal Configuration Scheme A.3.3. Switch and Jumper Settings
A.7. Clock Circuitry x
A.7.1. On-Board Oscillators A.7.2. Off-Board Clock Input/Output
A.8. Components and Interfaces x
A.8.1. 10/100/1000 Ethernet PHY A.8.2. Digital-to-Analog Converter A.8.3. HDMI Video Output A.8.4. HSMC A.8.5. Pmod Connectors A.8.6. USB to UART
A.9. Memory x
A.9.1. DDR3 Rev. B Board A.9.2. DDR3 Rev. C Board A.9.3. Flash
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions Thermal and Mechanical Injury Cooling Requirements Electro-Magnetic Interference (EMI) Telecommunications Port Restrictions Electrostatic Discharge (ESD) Warning Lithium Ion Battery Warnings
1. Overview
2. Getting Started
3. Board Test System
4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

C.1.2. Safety Cautions

Thermal and Mechanical Injury

Certain components such as heat sinks, power regulators, and processors may be hot. Heatsink fans are not guarded. Power supply fan may be accessible through guard. Care should be taken to avoid contact with these components.

Cooling Requirements

Maintain a minimum clearance area of 5 centimeters (2 inches) around the side, front and back of the board for cooling purposes. Do not block power supply ventilation holes and fan.

Electro-Magnetic Interference (EMI)

This equipment has not been tested for compliance with emission limits of FCC and similar international regulations. Use of this equipment in a residential location is prohibited. This equipment generates, uses and can radiate radio frequency energy which may result in harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, you are required to take measures to eliminate this interference.

Telecommunications Port Restrictions

The wireline telecommunications ports (modem, xDSL, T1/E1) on this product must not be connected to the Public Switched Telecommunication Network (PSTN) as it might result in disruption of the network. No formal telecommunication certification to FCC, R&TTE Directive, or other national requirements have been obtained.

Electrostatic Discharge (ESD) Warning

A properly grounded ESD wrist strap must be worn during operation/installation of the boards, connection of cables, or during installation or removal of daughter cards. Failure to use wrist straps can damage components within the system.

Attention: Please return this product to Intel for proper disposition. If it is not returned, refer to local environmental regulations for proper recycling. Do not dispose of this product in unsorted municipal waste.

Lithium Ion Battery Warnings

Lithium Battery: Risk of explosion if the lithium battery is replaced by an incorrect type. Risk of fire, explosion, or chemical burn if the battery is mistreated (punctured or crushed). Do not attempt to disassemble. Do not incinerate. Observe proper polarity when replacing battery. Do not dispose—the battery is intended to be serviced and disposed by qualified Intel® service personnel only.

Perchlorate Material: Special handling may apply. For more details, refer to www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is required by California Code of Regulations, Title 22, Division 4.5, Chapter 33: Best Management Practices for Perchlorate Materials. This product includes a battery which contains perchlorate material.

Taiwan battery recycling:

Please return this product to Intel® for proper disposition. If it is not returned, refer to local environmental regulations for proper recycling. Do not dispose of product in unsorted municipal waste.

Level Two Title