MAX® 10 FPGA Development Kit User Guide

Download PDF
ID 683460
Date 11/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Board Test System 4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation 2.4. Board Update Portal
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Software 2.3.2. Installing the Development Kit 2.3.3. Installing the Intel® FPGA Download Cable Driver
2.4. Board Update Portal x
2.4.1. Step 1: Connect to the Board Update Portal 2.4.2. Step 2: Update the User Software Portion
3. Board Test System x
3.1. Using the Configure Menu 3.2. The System Info Tab 3.3. The GPIO Tab 3.4. The Flash Tab 3.5. The HSMC Tab 3.6. The DDR3 Tab 3.7. The ADC Tab 3.8. The HDMI Tab 3.9. The Sleep Mode Tab 3.10. The Power Monitor 3.11. The Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Featured Device A.3. Configuration A.4. Status Elements A.5. Setup Elements A.6. General User Input/Output A.7. Clock Circuitry A.8. Components and Interfaces A.9. Memory A.10. Power Distribution System
A.3. Configuration x
A.3.1. Using the Quartus® Prime Programmer A.3.2. Selecting the Internal Configuration Scheme A.3.3. Switch and Jumper Settings
A.7. Clock Circuitry x
A.7.1. On-Board Oscillators A.7.2. Off-Board Clock Input/Output
A.8. Components and Interfaces x
A.8.1. 10/100/1000 Ethernet PHY A.8.2. Digital-to-Analog Converter A.8.3. HDMI Video Output A.8.4. HSMC A.8.5. Pmod Connectors A.8.6. USB to UART
A.9. Memory x
A.9.1. DDR3 Rev. B Board A.9.2. DDR3 Rev. C Board A.9.3. Flash
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Board Test System
4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

2.4. Board Update Portal

The Board Update Portal design example included in this development kit facilitates easy development of software and board flash memory updates, allowing you to access useful information on Intel website and to load software files into the Quad SPI flash memory on your board. The following steps ensure that you have the latest software available on both your computer and your board. The Board Update Portal design example, which includes a Nios® II embedded processor, an Ethernet media access control (MAC), and a web page, is stored in the “factory” portion of your board’s flash memory. The source for this design is installed with the development kit software. When your board is connected to a DHCP-enabled network, the Nios® II processor obtains an Internet protocol address and allows you to interface with your board over the network through a web page.
Before you begin, ensure that you have the following:
  • A computer with a connection to a working Ethernet port on a DHCP-enabled network.
  • A separate working Ethernet port connected to the same network for your board.
  • The Ethernet, power cables, and development board included in your kit.

Section Content
Step 1: Connect to the Board Update Portal
Step 2: Update the User Software Portion

Level Two Title