MAX® 10 FPGA Development Kit User Guide

Download PDF
ID 683460
Date 11/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Board Test System 4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide A. Development Kit Components B. Developer Resources C. Safety and Regulatory Compliance Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents
2. Getting Started x
2.1. Before You Begin 2.2. Handling the Board 2.3. Software and Driver Installation 2.4. Board Update Portal
2.3. Software and Driver Installation x
2.3.1. Installing the Quartus® Prime Software 2.3.2. Installing the Development Kit 2.3.3. Installing the Intel® FPGA Download Cable Driver
2.4. Board Update Portal x
2.4.1. Step 1: Connect to the Board Update Portal 2.4.2. Step 2: Update the User Software Portion
3. Board Test System x
3.1. Using the Configure Menu 3.2. The System Info Tab 3.3. The GPIO Tab 3.4. The Flash Tab 3.5. The HSMC Tab 3.6. The DDR3 Tab 3.7. The ADC Tab 3.8. The HDMI Tab 3.9. The Sleep Mode Tab 3.10. The Power Monitor 3.11. The Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Featured Device A.3. Configuration A.4. Status Elements A.5. Setup Elements A.6. General User Input/Output A.7. Clock Circuitry A.8. Components and Interfaces A.9. Memory A.10. Power Distribution System
A.3. Configuration x
A.3.1. Using the Quartus® Prime Programmer A.3.2. Selecting the Internal Configuration Scheme A.3.3. Switch and Jumper Settings
A.7. Clock Circuitry x
A.7.1. On-Board Oscillators A.7.2. Off-Board Clock Input/Output
A.8. Components and Interfaces x
A.8.1. 10/100/1000 Ethernet PHY A.8.2. Digital-to-Analog Converter A.8.3. HDMI Video Output A.8.4. HSMC A.8.5. Pmod Connectors A.8.6. USB to UART
A.9. Memory x
A.9.1. DDR3 Rev. B Board A.9.2. DDR3 Rev. C Board A.9.3. Flash
C. Safety and Regulatory Compliance Information x
C.1. Safety and Regulatory Information C.2. Compliance Information
C.1. Safety and Regulatory Information x
ENGINEERING DEVELOPMENT PRODUCT - NOT FOR RESALE OR LEASE C.1.1. Safety Warnings C.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Board Test System
4. Document Revision History for the MAX® 10 FPGA Development Kit User Guide
A. Development Kit Components
B. Developer Resources
C. Safety and Regulatory Compliance Information

C.1. Safety and Regulatory Information

ENGINEERING DEVELOPMENT PRODUCT - NOT FOR RESALE OR LEASE

This development kit is intended for laboratory development and engineering use only.

This development kit is designed to allow:
  • Product developers and system engineers to evaluate electronic components, circuits, or software associated with the development kit to determine whether to incorporate such items in a finished product.
  • Software developers to write software applications for use with the end product.

This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required Federal Communications Commission (FCC) equipment authorizations are first obtained.

Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.

Unless the assembled kit is designed to operate under Part 15, Part 18 or Part 95 of the United States Code of Federal Regulations (CFR) Title 47, the operator of the kit must operate under the authority of an FCC licenseholder or must secure an experimental authorization under Part 5 of the United States CFR Title 47.

Safety Assessment and CE & UKCA mark requirements have been completed, however, other certifications that may be required for installation and operation in your region have not been obtained.


Section Content
Safety Warnings
Safety Cautions

Level Two Title