AN 737: SEU Detection and Recovery in Arria® 10 Devices

Download PDF
ID 683064
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Quartus® Prime Software SEU FIT Reports 3. Arria® 10 Error Detection and Correction Feature Architecture 4. Guidelines for Error Detection CRC and Error Correction Feature 5. Guidelines for Embedded Memory ECC Feature 6. Arria® 10 EDCRC Reference Design 7. Implementing ECC Feature in Arria® 10 ROM Design 8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain 9. Document Revision History for AN 737: SEU Detection and Recovery in Arria® 10 Devices
2. Quartus® Prime Software SEU FIT Reports x
2.1. Enabling the Projected SEU FIT by Component Usage Report 2.2. SEU FIT Parameters Report 2.3. Projected SEU FIT by Component Usage Report
2.3. Projected SEU FIT by Component Usage Report x
2.3.1. Component FIT Rates 2.3.2. Raw FIT 2.3.3. Utilized FIT 2.3.4. Mitigated FIT 2.3.5. Architectural Vulnerability Factor
2.3.3. Utilized FIT x
2.3.3.1. Comparing .smh Critical Bits Report to Utilized Bit Count 2.3.3.2. Considerations for Small Designs
3. Arria® 10 Error Detection and Correction Feature Architecture x
3.1. Error Detection and Correction for CRAM 3.2. Memory Blocks Error Correction Code Support
3.1. Error Detection and Correction for CRAM x
3.1.1. Error Detection Cyclic Redundancy Check 3.1.2. Recovering from CRC Errors
3.1.1. Error Detection Cyclic Redundancy Check x
3.1.1.1. Column-Based and Frame-Based Check-Bits 3.1.1.2. Error Message Register
4. Guidelines for Error Detection CRC and Error Correction Feature x
4.1. Error Detection 4.2. Enabling Error Correction (Internal Scrubbing) 4.3. Interpreting CRC_ERROR
4.1. Error Detection x
4.1.1. Enabling Error Detection 4.1.2. Reading EMR
4.1.1. Enabling Error Detection x
4.1.1.1. Enabling the Error Detection CRC_ERROR Pin
4.1.2. Reading EMR x
4.1.2.1. Reading EMR using EMR Unloader IP Core 4.1.2.2. Reading EMR using HPS 4.1.2.3. Reading EMR using JTAG Interface
4.3. Interpreting CRC_ERROR x
4.3.1. CRC_ERROR Pin Behavior 4.3.2. Correctable and Uncorrectable Error
6. Arria® 10 EDCRC Reference Design x
6.1. System Requirements 6.2. Creating Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys 6.3. Design Testing with Fault Injection Debugger
6.2. Creating Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys x
6.2.1. Starting Quartus® Prime Software and Opening the Reference Design Project 6.2.2. Creating New Qsys System 6.2.3. Generating Qsys System 6.2.4. Integrating Qsys System into Quartus Prime Project
6.2.2. Creating New Qsys System x
6.2.2.1. Specifying Target FPGA and Clock Settings 6.2.2.2. Adding Altera IOPLL IP Core 6.2.2.3. Adding EMR Unloader IP Core 6.2.2.4. Adding Advance SEU Detection IP Core 6.2.2.5. Adding Fault Injection IP Core 6.2.2.6. Adding Avalon-ST Splitter 6.2.2.7. Adding Serial Flash Controller
6.2.4. Integrating Qsys System into Quartus Prime Project x
6.2.4.1. Generating In-System Source and Probe IP Core 6.2.4.2. Quartus Prime Project Settings 6.2.4.3. Assigning ASD Regions 6.2.4.4. Assigning FPGA Pin Location 6.2.4.5. Compiling the Project
6.3. Design Testing with Fault Injection Debugger x
6.3.1. Converting .sof File and .smh File to .jic File 6.3.2. Programing .jic File into EPCQ-L 6.3.3. Launching Signal Tap Logic Analyzer 6.3.4. Configuring Arria® 10 and Reading .smh File with Fault Injection Debugger 6.3.5. Injecting Error with Fault Injection Debugger
7. Implementing ECC Feature in Arria® 10 ROM Design x
7.1. Examples of Error Detection and Correction
1. Overview
2. Quartus® Prime Software SEU FIT Reports
3. Arria® 10 Error Detection and Correction Feature Architecture
4. Guidelines for Error Detection CRC and Error Correction Feature
5. Guidelines for Embedded Memory ECC Feature
6. Arria® 10 EDCRC Reference Design
7. Implementing ECC Feature in Arria® 10 ROM Design
8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain
9. Document Revision History for AN 737: SEU Detection and Recovery in Arria® 10 Devices

4.1.2.1. Reading EMR using EMR Unloader IP Core

You can instantiate the EMR Unloader IP core to detect SEU and unload EMR content in user logic. The EDCRC feature will be turned on automatically when the EMR Unloader IP core is instantiated. EMR Unloader IP core helps you to read the EMR whenever there is an SEU event by:

  • Unloading the EMR via core logic
  • Accessing the hard CRC Block
  • Providing access to the user logic to read the EMR data
Figure 6. EMR Unloader IP Core Block Diagram
Related Information
Level Two Title