AN 737: SEU Detection and Recovery in Arria® 10 Devices

Download PDF
ID 683064
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Quartus® Prime Software SEU FIT Reports 3. Arria® 10 Error Detection and Correction Feature Architecture 4. Guidelines for Error Detection CRC and Error Correction Feature 5. Guidelines for Embedded Memory ECC Feature 6. Arria® 10 EDCRC Reference Design 7. Implementing ECC Feature in Arria® 10 ROM Design 8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain 9. Document Revision History for AN 737: SEU Detection and Recovery in Arria® 10 Devices
2. Quartus® Prime Software SEU FIT Reports x
2.1. Enabling the Projected SEU FIT by Component Usage Report 2.2. SEU FIT Parameters Report 2.3. Projected SEU FIT by Component Usage Report
2.3. Projected SEU FIT by Component Usage Report x
2.3.1. Component FIT Rates 2.3.2. Raw FIT 2.3.3. Utilized FIT 2.3.4. Mitigated FIT 2.3.5. Architectural Vulnerability Factor
2.3.3. Utilized FIT x
2.3.3.1. Comparing .smh Critical Bits Report to Utilized Bit Count 2.3.3.2. Considerations for Small Designs
3. Arria® 10 Error Detection and Correction Feature Architecture x
3.1. Error Detection and Correction for CRAM 3.2. Memory Blocks Error Correction Code Support
3.1. Error Detection and Correction for CRAM x
3.1.1. Error Detection Cyclic Redundancy Check 3.1.2. Recovering from CRC Errors
3.1.1. Error Detection Cyclic Redundancy Check x
3.1.1.1. Column-Based and Frame-Based Check-Bits 3.1.1.2. Error Message Register
4. Guidelines for Error Detection CRC and Error Correction Feature x
4.1. Error Detection 4.2. Enabling Error Correction (Internal Scrubbing) 4.3. Interpreting CRC_ERROR
4.1. Error Detection x
4.1.1. Enabling Error Detection 4.1.2. Reading EMR
4.1.1. Enabling Error Detection x
4.1.1.1. Enabling the Error Detection CRC_ERROR Pin
4.1.2. Reading EMR x
4.1.2.1. Reading EMR using EMR Unloader IP Core 4.1.2.2. Reading EMR using HPS 4.1.2.3. Reading EMR using JTAG Interface
4.3. Interpreting CRC_ERROR x
4.3.1. CRC_ERROR Pin Behavior 4.3.2. Correctable and Uncorrectable Error
6. Arria® 10 EDCRC Reference Design x
6.1. System Requirements 6.2. Creating Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys 6.3. Design Testing with Fault Injection Debugger
6.2. Creating Arria® 10 SEU Fault Injection and Hierarchy Tagging Design with Qsys x
6.2.1. Starting Quartus® Prime Software and Opening the Reference Design Project 6.2.2. Creating New Qsys System 6.2.3. Generating Qsys System 6.2.4. Integrating Qsys System into Quartus Prime Project
6.2.2. Creating New Qsys System x
6.2.2.1. Specifying Target FPGA and Clock Settings 6.2.2.2. Adding Altera IOPLL IP Core 6.2.2.3. Adding EMR Unloader IP Core 6.2.2.4. Adding Advance SEU Detection IP Core 6.2.2.5. Adding Fault Injection IP Core 6.2.2.6. Adding Avalon-ST Splitter 6.2.2.7. Adding Serial Flash Controller
6.2.4. Integrating Qsys System into Quartus Prime Project x
6.2.4.1. Generating In-System Source and Probe IP Core 6.2.4.2. Quartus Prime Project Settings 6.2.4.3. Assigning ASD Regions 6.2.4.4. Assigning FPGA Pin Location 6.2.4.5. Compiling the Project
6.3. Design Testing with Fault Injection Debugger x
6.3.1. Converting .sof File and .smh File to .jic File 6.3.2. Programing .jic File into EPCQ-L 6.3.3. Launching Signal Tap Logic Analyzer 6.3.4. Configuring Arria® 10 and Reading .smh File with Fault Injection Debugger 6.3.5. Injecting Error with Fault Injection Debugger
7. Implementing ECC Feature in Arria® 10 ROM Design x
7.1. Examples of Error Detection and Correction
1. Overview
2. Quartus® Prime Software SEU FIT Reports
3. Arria® 10 Error Detection and Correction Feature Architecture
4. Guidelines for Error Detection CRC and Error Correction Feature
5. Guidelines for Embedded Memory ECC Feature
6. Arria® 10 EDCRC Reference Design
7. Implementing ECC Feature in Arria® 10 ROM Design
8. Modifying Single-Device .jam Files for Use in a Multi-Device JTAG Chain
9. Document Revision History for AN 737: SEU Detection and Recovery in Arria® 10 Devices

6.2.3. Generating Qsys System

To generate the Qsys system, perform the following steps:

  1. Click Generate HDL from Generate menu.
  2. Click Generate. Click Yes when the Save Changes? dialog box appears.
  3. Type asd_fi_system in the File name box and click Save. The Generate dialog box appears and system generation process begins.
  4. Click Close to close the dialog box.
  5. On the File menu, click Exit to close Qsys and return to the Quartus Prime software.
    You are ready to integrate the Qsys system into Quartus® Prime project.
Level Two Title