External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

Download PDF
ID 772538
Date 12/04/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP 2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction 3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture 4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals 5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP 6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support 7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support 8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support 9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure 10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization 11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging 12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP x
1.1. Release Information
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction x
2.1. Intel Agilex® 7 M-Series EMIF IP Protocol and Feature Support 2.2. Intel Agilex® 7 M-Series EMIF IP Design Flow 2.3. Intel Agilex® 7 M-Series EMIF IP Design Checklist
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture x
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction 3.2. Intel Agilex® 7 M-Series EMIF Sequencer 3.3. Intel Agilex® 7 M-Series EMIF Controller 3.4. Intel Agilex® 7 M-Series EMIF IP for Hard Processor Subsystem (HPS)
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction x
3.1.1. Intel Agilex® 7 M-Series EMIF Architecture: I/O Subsystem 3.1.2. Intel Agilex® 7 M-Series EMIF Architecture: I/O SSM 3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank 3.1.4. Intel Agilex® 7 M-Series EMIF Architecture: I/O Lane 3.1.5. Intel Agilex® 7 M-Series EMIF Architecture: Input DQS Clock Tree 3.1.6. Intel Agilex® 7 M-Series EMIF Architecture: PHY Clock Tree 3.1.7. Intel Agilex® 7 M-Series EMIF Architecture: PLL Reference Clock Networks 3.1.8. Intel Agilex® 7 M-Series EMIF Architecture: Clock Phase Alignment 3.1.9. User Clock in Different Core Access Modes
3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank x
3.1.3.1. Lockstep Configuration 3.1.3.2. DDR4 Pin Placement 3.1.3.3. DDR5 Pin Placement 3.1.3.4. LPDDR5 Pin Placement 3.1.3.5. I/O Sub-Bank Usage
3.2. Intel Agilex® 7 M-Series EMIF Sequencer x
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions x
3.2.1.1. Mailbox Supported Commands 3.2.1.2. Mailbox Command Definitions
3.3. Intel Agilex® 7 M-Series EMIF Controller x
3.3.1. Hard Memory Controller
3.3.1. Hard Memory Controller x
3.3.1.1. Hard Memory Controller Features
4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals x
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR4 4.2. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR5 4.3. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for LPDDR5 4.4. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for EMIF Calibration Component
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR4 x
4.1.1. ref_clk for EMIF 4.1.2. core_init_n for EMIF 4.1.3. usr_async_clk for EMIF 4.1.4. usr_clk for EMIF 4.1.5. usr_rst_n for EMIF 4.1.6. s0_axi4 for EMIF 4.1.7. mem for EMIF 4.1.8. oct for EMIF
4.2. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR5 x
4.2.1. ref_clk for EMIF 4.2.2. core_init_n for EMIF 4.2.3. usr_async_clk for EMIF 4.2.4. usr_clk for EMIF 4.2.5. usr_rst_n for EMIF 4.2.6. s0_axi4 for EMIF 4.2.7. mem for EMIF 4.2.8. i3c for EMIF 4.2.9. mem_lbd for EMIF 4.2.10. mem_lbs for EMIF 4.2.11. oct for EMIF
4.3. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for LPDDR5 x
4.3.1. ref_clk for EMIF 4.3.2. core_init_n for EMIF 4.3.3. usr_async_clk for EMIF 4.3.4. usr_clk for EMIF 4.3.5. usr_rst_n for EMIF 4.3.6. s0_axi4 for EMIF 4.3.7. mem for EMIF 4.3.8. oct for EMIF
4.4. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for EMIF Calibration Component x
4.4.1. s0_axi4lite_clk for EMIF 4.4.2. s0_axi4lite_rst_n for EMIF 4.4.3. s0_axi4lite for EMIF
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP x
5.1. Simulation Walkthrough
5.1. Simulation Walkthrough x
5.1.1. Calibration 5.1.2. Simulation Scripts 5.1.3. Functional Simulation with Verilog HDL 5.1.4. Simulating the Design Example
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support x
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 6.3. DDR4 Board Design Guidelines
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 x
6.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for DDR4 6.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (DDR4) Parameter Descriptions 6.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 6.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
6.2.1.1. Estimating Pin Requirements 6.2.1.2. DIMM Options 6.2.1.3. Maximum Number of Interfaces
6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
6.2.2.1. OCT 6.2.2.2. PLL
6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP x
6.2.4.1. Address and Command Pin Placement for DDR4 6.2.4.2. DDR4 Data Width Mapping 6.2.4.3. General Guidelines - DDR4 6.2.4.4. x4 DIMM Implementation 6.2.4.5. Specific Pin Connection Requirements 6.2.4.6. Command and Address Signals 6.2.4.7. Clock Signals 6.2.4.8. Data, Data Strobes, DM/DBI, and Optional ECC Signals
6.3. DDR4 Board Design Guidelines x
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices 6.3.2. General Layout Routing Guidelines 6.3.3. Reference Stackup 6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies 6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices x
6.3.1.1. Dynamic On-Chip Termination (OCT) 6.3.1.2. Dynamic On-Die Termination (ODT) in DDR4 6.3.1.3. Choosing Terminations on Intel Agilex® 7 M-Series FPGA Devices 6.3.1.4. On-Chip Termination Recommendations for Intel Agilex® 7 M-Series FPGA Devices
6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies x
6.3.4.1. One DIMM per Channel (1DPC) for UDIMM, RDIMM, and SODIMM DDR4 Topologies 6.3.4.2. Skew Matching Guidelines for DIMM Configurations 6.3.4.3. Power Delivery Recommendations for the Memory / DIMM Side
6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies x
6.3.5.1. Single Rank x 8 Discrete (Component) Topology 6.3.5.2. Single Rank x 16 Discrete (Component) Topology 6.3.5.3. ADDR/CMD Reference Voltage/RESET Signal Routing Guidelines for Single Rank x 8 and Single Rank x 16 Discrete (Component) Topologies 6.3.5.4. Skew Matching Guidelines for DDR4 Discrete Configurations 6.3.5.5. Power Delivery Recommendations for DDR4 Discrete Configurations 6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
6.3.5.6.1. DDR4 Byte Lane Swapping 6.3.5.6.2. DDR4 Address and Command and CLK Lane 6.3.5.6.3. DDR4 Interface x8 Data Lane 6.3.5.6.4. DDR4 Interface x4 Data Lane 6.3.5.6.5. Pin Swizzling
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support x
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 7.3. DDR5 Board Design Guidelines
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 x
7.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for DDR5 7.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (DDR5) Parameter Descriptions 7.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP 7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
7.2.1.1. Estimating Pin Requirements 7.2.1.2. DIMM Options 7.2.1.3. Maximum Number of Interfaces
7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
7.2.2.1. OCT 7.2.2.2. PLL
7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
7.2.3.1. General Guidelines - DDR5 7.2.3.2. x4 DIMM Implementation 7.2.3.3. Specific Pin Connection Requirements 7.2.3.4. Command and Address Signals 7.2.3.5. Clock Signals 7.2.3.6. Data, Data Strobes, DM, and Optional ECC Signals
7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP x
7.2.4.1. Address and Command Pin Placement for DDR5 7.2.4.2. DDR5 Data Width Mapping
7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
7.2.5.1. DDR5 Byte Lane Swapping 7.2.5.2. DDR5 Address and Command and CLK Lane 7.2.5.3. DDR5 Interface x8 Data Lane 7.2.5.4. DDR5 Interface x4 Data Lane 7.2.5.5. Pin Swizzling
7.3. DDR5 Board Design Guidelines x
7.3.1. PCB Stack-up and Design Considerations 7.3.2. General Design Considerations 7.3.3. DDR Differential Signals Routing 7.3.4. Ground Plane and Return Path 7.3.5. RDIMM, UDIMM, and SODIMM Break-in Layout Guidelines 7.3.6. DRAM Break-in Layout Guidelines 7.3.7. DDR5 PCB Layout Guidelines 7.3.8. DDR5 Simulation Strategy
7.3.7. DDR5 PCB Layout Guidelines x
7.3.7.1. DDR5 Discrete Component/Memory Down Topology: up to 40-Bit Interface (1 Rank x8 or x16, 2 Rank x8 or x16) 7.3.7.2. Routing Guidelines for DDR5 Memory Down: 1 Rank or 2 Rank (x8 bit or x16 bit) Configurations 7.3.7.3. Routing Guidelines for DDR5 RDIMM, UDIMM, and SODIMM Configurations 7.3.7.4. Example of a DDR5 layout on Intel FPGA Platform Board
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support x
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 8.3. LPDDR5 Board Design Guidelines
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 x
8.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for LPDDR5 8.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (LPDDR5) Parameter Descriptions 8.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
8.2.1.1. Estimating Pin Requirements 8.2.1.2. DIMM Options 8.2.1.3. Maximum Number of Interfaces
8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
8.2.2.1. OCT 8.2.2.2. PLL
8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
8.2.3.1. General Guidelines - LPDDR5 8.2.3.2. Specific Pin Connection Requirements 8.2.3.3. Command and Address Signals 8.2.3.4. Clock Signals
8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP x
8.2.4.1. Address and Command Pin Placement for LPDDR5 8.2.4.2. LPDDR5 Data Width Mapping 8.2.4.3. LPDDR5 Byte Lane Swapping
8.3. LPDDR5 Board Design Guidelines x
8.3.1. PCB Stack-up and Design Considerations 8.3.2. General Design Considerations 8.3.3. DDR Differential Signals Routing 8.3.4. Ground Plane and Return Path 8.3.5. DRAM Break-in Layout Guidelines 8.3.6. LPDDR5 PCB Layout Guidelines 8.3.7. LPDDR5 Simulation Strategy
8.3.6. LPDDR5 PCB Layout Guidelines x
8.3.6.1. LPDDR5 Discrete Component/Memory Down Topology (1 Rank or 2 Rank, up to 64 Bit Interface) 8.3.6.2. Supported LPDDR5 Topologies 8.3.6.3. Example of an LPDDR5 Layout on an Intel® FPGA Platform Board
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure x
9.1. Timing Closure 9.2. Optimizing Timing
9.1. Timing Closure x
9.1.1. Timing Analysis
9.1.1. Timing Analysis x
9.1.1.1. PHY or Core
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization x
10.1. Interface Standard 10.2. Bank Management Efficiency 10.3. Data Transfer 10.4. Improving Controller Efficiency
10.4. Improving Controller Efficiency x
10.4.1. Frequency of Operation 10.4.2. Series of Reads or Writes
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging x
11.1. Interface Configuration Performance Issues 11.2. Functional Issue Evaluation 11.3. Timing Issue Characteristics 11.4. Verifying Memory IP Using the Signal Tap Logic Analyzer 11.5. Generating Traffic with the Test Engine IP 11.6. Guidelines for Developing HDL for Traffic Generator 11.7. Debugging with the External Memory Interface Debug Toolkit
11.1. Interface Configuration Performance Issues x
11.1.1. Interface Configuration Bottleneck and Efficiency Issues
11.2. Functional Issue Evaluation x
11.2.1. Intel® IP Memory Model 11.2.2. Vendor Memory Model 11.2.3. Transcript Window Messages
11.3. Timing Issue Characteristics x
11.3.1. Evaluating FPGA Timing Issues 11.3.2. Evaluating External Memory Interface Timing Issues
11.7. Debugging with the External Memory Interface Debug Toolkit x
11.7.1. Prerequisites for Using the EMIF Debug Toolkit 11.7.2. Configuring Your Design to Use the EMIF Debug Toolkit 11.7.3. Launching the EMIF Debug Toolkit 11.7.4. Using the EMIF Debug Toolkit
11.7.4. Using the EMIF Debug Toolkit x
11.7.4.1. Rerunning Calibration 11.7.4.2. Rerunning the Test Engine 11.7.4.3. Saving Debug Print 11.7.4.4. Calibration Reports 11.7.4.5. Driver Margining Tab 11.7.4.6. Pin Delay Settings Tab
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture
4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging
12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

3.2.1.2. Mailbox Command Definitions

Table 19.  CMD_TYPE Definition
CMD_TYPE Value Description
CMD_NOP 0x00 No operation command.
CMD_GET_SYS_INFO 0x01 Retrieving information about the IO96B configuration.
CMD_GET_MEM_INFO 0x02 Retrieving information about the memory interface operation.
CMD_TRIG_CONTROLLER_OP 0x04 Triggering memory controller-related operations.
CMD_TRIG_MEM_CAL_OP 0x05 Triggering calibration events.
Table 20.  CMD_REQ Definition
Bit Name Description Access Reset
[31:29] CMD_TARGET_IP_TYPE Indicates the type of IP, as follows:
  • 0x0 – Not used.
  • 0x1 – Primary MC of primary IO96B.
  • 0x2 – Secondary MC of primary IO96B.
  • 0x3 – Primary MC of secondary IO96B.
  • 0x4 – Secondary MC of secondary IO96B.
 Read-Write 0x0
[28:24] CMD_TARGET_IP_INSTANCE_ID IP identifier. Read-Write 0x00
[23:16] CMD_TYPE The type of command that the user wants the firmware to perform. Read-Write 0x00
[15:0] CMD_OPCODE The opcode of the command that the user wants the firmware to perform. Read-Write 0x00
Table 21.  CMD_TARGET_IP_TYPE Definition
Multi-channel/Lockstep Configurations CMD_TARGET_IP_TYPE
1 – Primary MC, Primary IO96B 2 – Secondary MC, Primary IO96B 3 – Primary MC, Secondary IO96B 4 – Secondary MC, Secondary IO96B
LPDDR4/5 2CHx16 CH1 CH2    
LPDDR4/5 4CHx16 CH1 CH2 CH3 CH4
DDR5 2CHx16 CH1 CH2    
DDR5 2CHx32 CH1   CH2  
DDR5 x40 lockstep CH1 *    
DDR4 x40 lockstep CH1 *    
DDR4 x64, x72 lockstep CH1 * * *
Note: * These controllers are used but have no (or limited) mailbox features due to limited lockstep capabilities.
Table 22.  Command Definitions
CMD_REQ Description

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <UNUSED>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <UNUSED>

CMD_REQ [23:16]: CMD_TYPE = CMD_GET_SYS_INFO

CMD_REQ [15:0]: CMD_OPCODE = GET_MEM_INTF_INFO

Command to get the memory interface IP type and instance ID of all the IPs in the IO96B.

[Inputs] N/A

[Outputs[KSH1] [VCV2] [KSH3] ]

CMD_RESPONSE_DATA_SHORT [1:0]: NUM_USED_MEM_INTF

Number of memory interfaces instantiated.

CMD_RESPONSE_DATA_0 [31:29]: INTF_0_IP_TYPE Indicates the type of IP for Interface 0:

0x0 – Not used

0x1 – EMIF

CMD_RESPONSE_DATA_0 [28:24]: INTF_0_INSTANCE_ID IP identifier for Interface 0.

CMD_RESPONSE_DATA_1 [31:29]: INTF_1_IP_TYPE

Indicates the type of IP for Interface 1:

0x0 – Not used

0x1 – EMIF

CMD_RESPONSE_DATA_1 [28:24]: INTF_1_INSTANCE_ID

IP identifier for Interface 1.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_GET_MEM_INFO

CMD_REQ [15:0]: CMD_OPCODE = GET_MEM_TECHNOLOGY

Command to get the memory technology of the memory interface specified using the instance ID.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT [2:0]: MEM_TECHNOLOGY

Reports the memory type as below:

0x0 = DDR4, 0x1 = DDR5, 0x2 = DDR5_RDIMM, 0x3 = LPDDR4, 0x4 = LPDDR5, 0x5 = QDRIV

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_GET_MEM_INFO

CMD_REQ [15:0]: CMD_OPCODE = GET_MEMCLK_FREQ_KHZ

Command to get the memory clock frequency of the memory interface specified using the instance ID.

[Inputs]

CMD_PARAM_0 [1:0]: FREQUENCY_SET_POINT

Get clock frequency for the specified frequency set point.

0x0 = Frequency set point 0

0x1 = Frequency set point 1

0x2 = Frequency set point 2

CMD_PARAM_0 [2:2]: USE_CURRENT_FSP

Get clock frequency for the current frequency set point.

0x0 = Use FSP specified using FREQUENCY_SET_POINT.

0x1 = Use current FSP

[Outputs]

CMD_RESPONSE_DATA_0: DRAM_CLK_FREQ_KHZ

Reports the memory clock frequency in KHz for the input frequency set point.

[Errors]

CMD_RESPONSE_STATUS - STATUS_CMD_RESPONSE_ERROR:

000 – No errors

111 – The FSP specified using FREQUENCY_SET_POINT is not defined.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_GET_MEM_INFO

CMD_REQ [15:0]: CMD_OPCODE = GET_MEM_WIDTH_INFO

Command to get the memory width information of the memory interface specified using the instance ID.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_0 [7:0]: DQ_WIDTH

CMD_RESPONSE_DATA_0 [15:8]: CS_WIDTH

CMD_RESPONSE_DATA_0 [23:16]: C_WIDTH

CMD_RESPONSE_DATA_1 [7:0]: TOTAL_MEM_CAPACITY

Memory device capacity in Gb (gigabits) calculated as:

CAPACITY = (DQ_WIDTH / DEVICE_WIDTH) * DEVICE_DENSITY

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_ENABLE_SET

Command to enable different ECC modes for the memory interface specified using the instance ID.

[Inputs]

CMD_PARAM_0 [1:0]: ECC_ENABLE

Set the current ECC error reporting (single-bit and double-bit errors) and correcting (single-bit errors) that is enabled.

’b00 = ECC is disabled. Data is written to the memory without ECC values, and data is returned to the user interface without being verified for accuracy.

’b01 = ECC is enabled, but without detection or correction.

’b10 = ECC is enabled with detection, but correction is not supported. When an error is found on a read operation, ECC reporting parameters are updated for read commands. Erroneous data is returned to the user on read commands and written to the memory on write commands.

’b11 = ECC is enabled with detection and correction. When an error is found on a read operation, the ECC reporting parameters are updated for read commands. Single bit errors are corrected automatically by the controller in both read and write commands.

CMD_PARAM_0[2:2]: ECC_TYPE

‘b0 = Out-of-Band ECC

‘b1 =In-line ECC

[Outputs] N/A

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_ENABLE_STATUS

Command to get the ECC enable status of the memory interface specified using the instance ID.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT [1:0]: ECC_ENABLE

Reports the current ECC error reporting (single-bit and double-bit errors) and correcting (single-bit errors) that is enabled.

’b00 = ECC is disabled. Data is written to the memory without ECC values, and data is returned to the user interface without being verified for accuracy.

’b01 = ECC is enabled, but without detection or correction.

’b10 = ECC is enabled with detection, but correction is not supported. When an error is found on a read operation, ECC reporting parameters are updated for read commands. Erroneous data is returned to the user on read commands and written to the memory on write commands.

’b11 = ECC is enabled with detection and correction. When an error is found on a read operation, the ECC reporting parameters are updated for read commands. Single bit errors are corrected automatically by the controller in both read and write commands.

CMD_RESPONSE_DATA_SHORT[2:2]:

ECC_TYPE

‘b0 = Out-of-Band ECC

‘b1 =In-line ECC

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_INTERRUPT_STATUS

Command to get status of ECC interrupts for the memory interface specified using the instance ID.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_0 [16:0]: ECC_INTERRUPT_STATUS

Reports the interrupts related to the ECC logic.

Bit [8] = An ECC correctable error has been detected in a scrubbing read operation

Bit [7] = The triggered scrub operation has completed.

Bit [6] = One or more ECC writeback commands could not be executed.

Bit [3] = Another un-correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [2] = An un-correctable ECC event has been detected on a read operation.

Bit [1] = Another correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [0] = A correctable ECC event has been detected on a read operation

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_INTERRUPT_ACK

Command to acknowledge and clear the ECC interrupts for the memory interface specified using the instance ID.

[Inputs]

CMD_PARAM_0 [16:0]: ECC_INTERRUPT_ACK

Used to acknowledge and clear the interrupts related to the ECC logic.

Bit [8] = An ECC correctable error has been detected in a scrubbing read operation

Bit [7] = The triggered scrub operation has completed.

Bit [6] = One or more ECC writeback commands could not be executed.

Bit [3] = Another un-correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [2] = An un-correctable ECC event has been detected on a read operation.

Bit [1] = Another correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [0] = A correctable ECC event has been detected on a read operation

[Outputs] N/A

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_INTERRUPT_MASK

Command to set mask for ECC interrupts for the memory interface specified using the instance ID, in order to disable specific ECC interrupts.

[Inputs]

CMD_PARAM_0 [16:0]: ECC_INTERRUPT_MASK

If any bit is set to ’b1 in this parameter, the corresponding interrupt does NOT trigger an interrupt on the top-level EMIF interrupt signal.

Bit [13] = A RMW Read Link ECC double-bit error has been detected

Bit [12] = A Read Link ECC double-bit error has been detected.

Bit [11] = A Read Link ECC single-bit error has been detected.

Bit [10] = A Write Link ECC double-bit error has been detected by the periodic MRR to MR43.

Bit [9] = A Write Link ECC single-bit error has been detected by the periodic MRR to MR43.

Bit [8] = An ECC correctable error has been detected in a scrubbing read operation

Bit [7] = The triggered scrub operation has completed.

Bit [6] = One or more ECC writeback commands could not be executed.

Bit [3] = Another un-correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [2] = An un-correctable ECC event has been detected on a read operation.

Bit [1] = Another correctable ECC event has been detected on a read operation, prior to the initial event being acknowledged.

Bit [0] = A correctable ECC event has been detected on a read operation

[Outputs] N/A

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_GET_SBE_INFO

Command to get the details on the single-bit (SBE) or correctable errors detected by ECC for the memory interface specified using the instance ID. This command should be called only if all of the following conditions are true:

1. A correctable ECC event occurs.

2. ECC is enabled in the ECC_ENABLE parameter (’b01, ’b10 or ’b11).

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_0 [31:0]: ECC_SBE_INFO_SIZE

Holds the size of the single bit error details. The value of this is 192 bits.

CMD_RESPONSE_DATA_1 [31:0]: ECC_SBE_INFO_PTR

Holds the offset pointer of the single bit error details. The data at the pointer location is as shown below:

OFFSET [0] to OFFSET [1]: ECC_SBE_ADDR [37:0]

Holds the address of the read data that caused a single-bit correctable ECC event. The Controller pads this parameter with zeros for any address bits not used by the controller. Here, the 5th bit of OFFSET [0] has the 37th bit, and the lowest bit of OFFSET [1] has the 0th bit of ECC_SBE_ADDR.

OFFSET [2] to OFFSET [3]: ECC_SBE_DATA [63:0]

Holds the pre-corrected data associated with a single-bit correctable ECC event.

OFFSET [4]: ECC_SBE_ID [6:0]

Holds the source ID associated with a single-bit correctable ECC event. For AXI ports, the source ID is comprised of the Port ID (upper bit/s) and the Requestor ID, where the Requestor ID is the axi0_AWID for write commands or the axi0_ARID for read commands.

OFFSET [5]: ECC_SBE_SYND [7:0]

Holds the syndrome value associated with a single-bit correctable ECC error event. This value indicates which bit of the check code or data was erroneous. Table 7 shows the syndrome corresponding to the single bit errors.

[Command-Specific Errors]

‘b000 – No errors

‘b001 – ECC not enabled

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_GET_DBE_INFO

Command to get the details on the double-bit (DBE) or uncorrectable errors detected by ECC for the memory interface specified using the instance ID. This command should be called only if all of the following conditions are true:

1. An uncorrectable ECC event occurs.

2. ECC is enabled in the ECC_ENABLE parameter (’b01, ’b10 or ’b11.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_0 [31:0]: ECC_DBE_INFO_SIZE

Holds the size of the double bit error details. The value of this will be 192 bits.

CMD_RESPONSE_DATA_1 [31:0]: ECC_DBE_INFO_PTR

Holds the offset pointer of the double bit error details. The data at the pointer location is as shown below:

OFFSET [0] to OFFSET [1]: ECC_DBE_ADDR [37:0]

Holds the address of the read data that caused a double-bit uncorrectable ECC event. The Controller pads this parameter with zeros for any address bits not used by the controller. Here, the 5th bit of OFFSET [0] has the 37th bit, and the lowest bit of OFFSET [1] has the 0th bit of ECC_SBE_ADDR.

OFFSET [2] to OFFSET [3]: ECC_DBE_DATA [63:0]

Holds the data associated with a double-bit uncorrectable ECC event.

OFFSET [4]: ECC_DBE_ID [6:0]

Holds the source ID associated with a double-bit uncorrectable ECC event. For AXI ports, the source ID is comprised of the Port ID (upper bit/s) and the Requestor ID, where the Requestor ID is the axi0_AWID for write commands or the axi0_ARID for read commands.

OFFSET [5]: ECC_DBE_SYND [7:0]

Holds the syndrome bits associated with a double-bit un-correctable ECC error event. This controller can indicate that only 2 bits of the data and/or check code are erroneous but can not identify which bits. Table 7 shows the syndrome corresponding to the single bit errors.

[Command-Specific Errors]

‘b000 – No errors

‘b001 – ECC not enabled

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_SCRUB_IN_PROGRESS_STATUS

Command to check if the ECC scrub is in-progress for the memory interface specified using the instance ID.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: ECC_SCRUB_IN_PROGRESS

Reports the scrubbing operation status. This parameter is read-only. ’b0 = Not actively performing a scrubbing operation. ’b1 = The Controller is in the process of performing a scrubbing operation.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_SCRUB_MODE_0_START

Command to start ECC scrub in mode 0 where scrub is performed at regular intervals for the memory interface specified using the instance ID.

[Inputs]

CMD_PARAM_0 [15:0]: ECC_SCRUB_INTERVAL

Sets the minimum interval between two ECC scrubbing commands, in number of controller clock cycles. The controller clock is based on the Controller’s operating frequency. Clearing this parameter to 0x0000 disables interval operation.

CMD_PARAM_1 [11:0]: ECC_SCRUB_LEN

Defines the length (in bytes) of the ECC scrubbing read command that the controller will issue. This value must be an integer multiple of the memory burst length, and the lowest 3 bits of this parameter must be cleared to ’b0.

CMD_PARAM_2 [0:0]: ECC_SCRUB_FULL_MEM

Defines whether to perform ECC scrub on full memory or on the specified address range.

‘b0 – ECC scrub performed on address range specified using ECC_SCRUB_START_ADDR and ECC_SCRUB_END_ADDR

‘b1 – ECC scrub performed on full memory address range

CMD_PARAM_3 [31:0]: ECC_SCRUB_START_ADDR [31:0]

CMD_PARAM_4 [5:0]: ECC_SCRUB_START_ADDR [36:32]

Defines the starting address from where scrubbing operations begin. This value must be less than or equal to the value programmed into the ECC_SCRUB_END_ADDR parameter. Only used when ECC_SCRUB_FULL_MEM is ‘b0.

CMD_PARAM_5 [31:0]: ECC_SCRUB_END_ADDR [31:0]

CMD_PARAM_6 [5:0]: ECC_SCRUB_END_ADDR [36:32]

Defines the ending address at which scrubbing operations wrap around to the start address. This parameter must be programmed to a non-zero value for the scrubbing logic to operate. Only used when ECC_SCRUB_FULL_MEM is ‘b0.

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: ECC_SCRUB_INITIATED

‘b1 – ECC scrub initiated successfully

‘b0 – ECC scrub initiation failed

[Command-Specific Errors]

‘b000 – No errors

‘b001 – ECC not enabled

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = ECC_SCRUB_MODE_1_START

Command to start ECC scrub in mode 1 where scrub is performed when the controller is idle for the memory interface specified using the instance ID.

[Inputs]

CMD_PARAM_0 [15:0]: ECC_SCRUB_IDLE_CNT

Defines the number of controller clock cycles that the scrubbing engine waits in the Controller’s idle state before starting scrubbing operations. The Controller is considered idle when the command queue is empty. When this condition is detected, an internal counter loads with the value programmed in this parameter and count down on each controller clock. When the counter expires, either the scrubbing operation begins or the next address is tested. The controller clock is based on the Controller’s operating frequency. Clearing this parameter to 0x0000 disables idle operation.

CMD_PARAM_1 [11:0]: ECC_SCRUB_LEN

Defines the length (in bytes) of the ECC scrubbing read command that the controller issues. This value must be an integer multiple of the memory burst length, and the lowest 3 bits of this parameter must be cleared to ’b0.

CMD_PARAM_2 [0:0]: ECC_SCRUB_FULL_MEM

Defines whether to perform ECC scrub on full memory or on the specified address range.

‘b0 – ECC scrub performed on address range specified using ECC_SCRUB_START_ADDR and ECC_SCRUB_END_ADDR

‘b1 – ECC scrub performed on full memory address range

CMD_PARAM_3 [31:0]: ECC_SCRUB_START_ADDR [31:0]

CMD_PARAM_4 [5:0]: ECC_SCRUB_START_ADDR [36:32]

Defines the starting address from where scrubbing operations begin. This value must be less than or equal to the value

programmed into the ECC_SCRUB_END_ADDR parameter. Only used when ECC_SCRUB_FULL_MEM is ‘b0.

CMD_PARAM_5 [31:0]: ECC_SCRUB_END_ADDR [31:0]

CMD_PARAM_6 [5:0]: ECC_SCRUB_END_ADDR [36:32]

Defines the ending address at which scrubbing operations wrap around to the start address. This parameter must be programmed to a non-zero value for the scrubbing logic to operate. Only used when ECC_SCRUB_FULL_MEM is ‘b0.

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: ECC_SCRUB_INITIATED

‘b1 – ECC scrub initiated successfully

‘b0 – ECC scrub initiation failed

[Command-Specific Errors]

‘b000 – No errors

‘b001 – ECC not enabled

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_STANDARD_MODE_START

Command to initiate Original MOVI1 3N BIST algorithm for data checking for the memory interface specified using the instance ID. This command MUST be followed by BIST_RESULTS_STATUS to get the results of the BIST operation and resume normal operation of the memory controller.

[Inputs]

CMD_PARAM_0 [5:0]: BIST_ADDR_SPACE [5:0]

Used in BIST data checking to define the address space in bytes from 0 to 2addr_space that the BIST logic checks. As an example, if the addr_space parameter was programmed to 0x1c, then the BIST logic would check 228 bytes = 256 MBytes. Note: A BIST test must cover a minimum of 2 bursts. Therefore, the user must program this parameter to a value such that the start address and end address of the BIST test will encompass a minimum of 2 bursts. Only used if BIST_FULL_MEM is ‘b0.

CMD_PARAM_0 [6:6]: BIST_FULL_MEM

Defines whether to perform BIST on full memory or on the specified address range.

‘b0 – BIST performed on address range specified using BIST_START_ADDR and BIST_ADDR_SPACE

‘b1 – BIST performed on full memory address range

CMD_PARAM_1 [31:0]: BIST_START_ADDR [31:0]

CMD_PARAM_2 [5:0]: BIST_START_ADDR [36:32]

Used in BIST data checking and memory initialization programming to define the starting address for BIST checking in bytes. Only used if BIST_FULL_MEM is ‘b0.

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: BIST_INITIATED

‘b1 – BIST initiated successfully

‘b0 – BIST initiation failed

[Command-Specific Errors]

‘b00 – No errors

‘b01 – A previous command’s saved state not restored. For example, BIST_STANDARD_MODE_START should be followed by BIST_RESULTS_STATUS command to restored saved state and resume normal memory controller operation.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_RESULTS_STATUS

Command to get BIST results for the previously initiated BIST operation for memory interface specified using the instance ID

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: BIST_STATUS

Holds the status of the BIST operation.

’b0 = BIST operation still in progress if previously initiated.

’b1 = BIST operation has been completed.

[Command-Specific Error]

‘b00 – No errors

‘b01 – Could not restore saved state. BIST_STANDARD_MODE_START command MUST be immediately followed by BIST_RESULTS_STATUS to get the results of the BIST operation, restore saved state, and resume normal operation of the memory controller. The populated results, if any, may be invalid.

CMD_RESPONSE_DATA_SHORT [3:3]: BIST_RESULT

Holds the result of the BIST operation. For this BIST mode, the test ends at the first failure, or completely checks the specified data range if no failures are found. This value is valid when BIST_STATUS indicates that the BIST operation has completed.

’b0 = Data check failed. ’b1 = Data check passed.

CMD_RESPONSE_DATA_0 [31:0]: BIST_FAIL_RESULT_SIZE

Holds the size of the BIST failure results. The value of this will be 640 bits.

CMD_RESPONSE_DATA_1 [31:0]: BIST_FAIL_RESULT_PTR

Holds the offset pointer of the BIST failure results. The data at the pointer location is as shown below:

OFFSET [0] to OFFSET [8]: BIST_EXP_DATA [287:0]

Holds the expected read data for a BIST data check failure. Here, the highest bit of OFFSET [0] has the 287th bit, and the lowest bit of OFFSET [8] has the 0th bit of BIST_EXP_DATA.

OFFSET [9] to OFFSET [10]: BIST_FAIL_ADDR [37:0]

Holds the actual failing address for a BIST data check failure.

OFFSET [11] to OFFSET [20]: BIST_FAIL_DATA [287:0]

Holds the actual failing data for a BIST data check failure.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_MEM_INIT_START

Command to initiate memory initialization BIST for the memory interface specified using the instance ID. Memory initialization programming allows a selectable range of memory to be initialized with a programmable data value. This command MUST be followed by BIST_MEM_INIT_STATUS to get the results of the BIST memory initialization operation and resume normal operation of the memory controller.

[Inputs] N/A

CMD_PARAM_0 [5:0]: BIST_ADDR_SPACE [5:0]

Used in BIST data checking to define the address space in bytes from 0 to 2addr_space that the BIST logic checks. As an example, if the BIST_ADDR_SPACE parameter was programmed to 0x1c, then the BIST logic would check 228 bytes = 256 MBytes. Note: A BIST test must cover a minimum of 2 bursts. Therefore, you must program this parameter to a value such that the start address and end address of the BIST test encompass a minimum of 2 bursts. Only used if BIST_FULL_MEM is ‘b0.

CMD_PARAM_0 [6:6]: BIST_FULL_MEM

Defines whether to perform BIST on full memory or on the specified address range.

‘b0 – BIST performed on address range specified using BIST_START_ADDR and BIST_ADDR_SPACE

‘b1 – BIST performed on full memory address range

CMD_PARAM_1 [31:0]: BIST_START_ADDR [31:0]

CMD_PARAM_2 [5:0]: BIST_START_ADDR [37:32]

Used in BIST data checking and memory initialization programming to define the starting address for BIST checking in bytes. Only used if BIST_FULL_MEM is ‘b0.

CMD_PARAM_3: BIST_DATA_PATTERN

Specifies the data pattern to use for the memory initialization.

‘b00 – Initialize memory to all zeros.

‘b10 – Use data pattern specified using the values set using commands BIST_SET_DATA_PATTERN_UPPER and BIST_SET_DATA_PATTERN_LOWER before issuing BIST_MEM_INITIAL_START command.

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: BIST_INITIATED

‘b1 – BIST memory initialization initiated successfully

‘b0 – BIST memory initialization initiation failed

[Command-Specific Errors]

‘b00 – No errors

‘b01 – A previous command’s saved state not restored. For example, BIST_STANDARD_MODE_START should be followed by BIST_RESULTS_STATUS command to restored saved state and resume normal memory controller operation.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_MEM_INIT_STATUS

Command to get BIST memory initialization status for the previously initiated BIST operation for memory interface specified using the instance ID

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT [0:0]: BIST_STATUS

Holds the status of the BIST operation.

’b0 = BIST operation still in progress if previously initiated.

’b1 = BIST operation has been completed.

[Command-Specific Errors]

‘b00 – No errors

‘b01 – Could not restore saved state. BIST_MEM_INIT_START command MUST be immediately followed by BIST_MEM_INIT_STATUS to get the results of the BIST operation, restore saved state, and resume normal operation of the memory controller. The populated results, if any, may be invalid.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_SET_DATA_PATTERN_UPPER

CMD_PARAM_3 [31:0]: BIST_DATA_PATTERN [287:256]

CMD_PARAM_2 [31:0]: BIST_DATA_PATTERN [255:224]

CMD_PARAM_1 [31:0]: BIST_DATA_PATTERN [223:192]

CMD_PARAM_0 [31:0]: BIST_DATA_PATTERN [191:160]

Defines the data pattern bits [287:160] to be used. Only data corresponding to active portion of core word is used while the inactive portion is ignored.

[Outputs] N/A

[Command-Specific Errors]

‘b00 – No errors

‘b01 – Cannot set upper data pattern for slim interface.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = BIST_SET_DATA_PATTERN_LOWER

CMD_PARAM_4 [31:0]: BIST_DATA_PATTERN [159:128]

CMD_PARAM_3 [31:0]: BIST_DATA_PATTERN [127:96]

CMD_PARAM_2 [31:0]: BIST_DATA_PATTERN [95:64]

CMD_PARAM_1 [31:0]: BIST_DATA_PATTERN [63:32]

CMD_PARAM_0 [31:0]: BIST_DATA_PATTERN [31:0]

Defines the data pattern bits [223:0] to be used. Only data corresponding to active portion of the core word is used while inactive portion is ignored.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = LP_MODE_ENTER

Command to cause the Interface to enter a low power state. Note that other interface operations, including recalibration and mode register reads and writes, can cause automatic exits from some low-power states.

[Inputs]

CMD_PARAM_0[3:0]:

The low power state the interface will enter

‘b0001 – Active Power Down (All Protocols)

‘b0010 – Active Power Down with Memory Clock Gating (LPDDR4/LPDDR5 Only)

‘b0011 – Pre-Charge Power Down (All Protocols)

‘b0100 – Pre-Charge Power Down with Memory Clock Gating (LPDDR4/LPDDR5 Only)

‘b0101 – Self-Refresh Short (DDR4/DDR5 and LPDDR4 Only)

‘b0110 – Self-Refresh Short with Memory Clock Gating (DDR4/DDR5 Only)

‘b1000 – Self-Refresh Long (DDR4/DDR5 Only)

‘b1001 – Self-Refresh Long with Memory Clock Gating (DDR4/DDR5 Only)

‘b1010 – Self-Refresh Long with Memory Clock and Controller Clock Gating (DDR4/DDR5 Only)

‘b1011 – Self-Refresh Power Down Short (LPDDR4/LPDDR5 Only)

‘b1100 – Self-Refresh Power Down Short with Memory Clock Gating (LPDDR4/LPDDR5 Only)

‘b1101 – Self-Refresh Power Down Long (LPDDR4/LPDDR5 Only)

‘b1110 – Self-Refresh Power Down Long with Memory Clock Gating (LPDDR4/LPDDR5 Only)

‘b1111 – Self-Refresh Power Down Long with Memory and Controller Clock Gating (LPDDR4/LPDDR5 Only)

[Outputs] N/A

[Error Codes]

‘b000 – No errors

‘b001 – The Selected Low Power State is Not Available for the Current Protocol

‘b010 – The Selected Low Power State is invalid/Does not Exist.

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = LP_MODE_EXIT

Command to exit any low power state.

[Inputs] N/A

[Outputs] N/A

[Error Codes]

‘b000 – No errors

CMD_REQ [31:29]: CMD_TARGET_IP_TYPE = <TARGET_IP_TYPE>

CMD_REQ [28:24]: CMD_TARGET_IP_INSTANCE_ID = <TARGET_IP_INSTANCE_ID>

CMD_REQ [23:16]: CMD_TYPE = CMD_TRIG_CONTROLLER_OP

CMD_REQ [15:0]: CMD_OPCODE = LP_MODE_STATUS

Command to get the Current Low Power State of the Interface.

[Inputs] N/A

[Outputs]

CMD_RESPONSE_DATA_SHORT[0:0]:

Valid Bit. The Data in CMD_RESPONSE_DATA_0[5:0] is only valid if this bit is ‘b1.

‘b0 – Invalid, the Interface is currently transitioning into or out of a low power state

‘b1 – Valid.

CMD_RESPONSE_DATA_0[5:0]: Current Interface Low Power State

‘b000000 - Idle

‘b000001 – Active Power Down

‘b000010 – Active Power Down with Memory Clock Gating

‘b000011 – Pre-Charge Power Down

‘b000100 – Pre-Charge Power Down with Memory Clock Gating

‘b000101 – Self-Refresh Short

‘b000110 – Self-Refresh Short with Memory Clock Gating

‘b001000 – Self-Refresh Long

‘b001001 – Self-Refresh Long with Memory Clock Gating

‘b001010 – Self-Refresh Long with Memory Clock and Controller Clock Gating

‘b001011 – Self-Refresh Power Down Short

‘b001100 – Self-Refresh Power Down Short with Memory Clock Gating

‘b001101 – Self-Refresh Power Down

‘b001110 – Self-Refresh Power Down Long with Memory Clock Gating

‘b001111 – Self-Refresh Power Down Long with Memory and Controller Clock Gating

[Error Codes]

‘b000 – No errors
Level Two Title