External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

Download PDF
ID 772538
Date 12/04/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP 2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction 3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture 4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals 5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP 6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support 7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support 8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support 9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure 10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization 11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging 12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP x
1.1. Release Information
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction x
2.1. Intel Agilex® 7 M-Series EMIF IP Protocol and Feature Support 2.2. Intel Agilex® 7 M-Series EMIF IP Design Flow 2.3. Intel Agilex® 7 M-Series EMIF IP Design Checklist
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture x
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction 3.2. Intel Agilex® 7 M-Series EMIF Sequencer 3.3. Intel Agilex® 7 M-Series EMIF Controller 3.4. Intel Agilex® 7 M-Series EMIF IP for Hard Processor Subsystem (HPS)
3.1. Intel Agilex® 7 M-Series EMIF Architecture: Introduction x
3.1.1. Intel Agilex® 7 M-Series EMIF Architecture: I/O Subsystem 3.1.2. Intel Agilex® 7 M-Series EMIF Architecture: I/O SSM 3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank 3.1.4. Intel Agilex® 7 M-Series EMIF Architecture: I/O Lane 3.1.5. Intel Agilex® 7 M-Series EMIF Architecture: Input DQS Clock Tree 3.1.6. Intel Agilex® 7 M-Series EMIF Architecture: PHY Clock Tree 3.1.7. Intel Agilex® 7 M-Series EMIF Architecture: PLL Reference Clock Networks 3.1.8. Intel Agilex® 7 M-Series EMIF Architecture: Clock Phase Alignment 3.1.9. User Clock in Different Core Access Modes
3.1.3. Intel Agilex® 7 M-Series EMIF Architecture: I/O Bank x
3.1.3.1. Lockstep Configuration 3.1.3.2. DDR4 Pin Placement 3.1.3.3. DDR5 Pin Placement 3.1.3.4. LPDDR5 Pin Placement 3.1.3.5. I/O Sub-Bank Usage
3.2. Intel Agilex® 7 M-Series EMIF Sequencer x
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions
3.2.1. Intel Agilex® 7 M-Series Mailbox Structure and Register Definitions x
3.2.1.1. Mailbox Supported Commands 3.2.1.2. Mailbox Command Definitions
3.3. Intel Agilex® 7 M-Series EMIF Controller x
3.3.1. Hard Memory Controller
3.3.1. Hard Memory Controller x
3.3.1.1. Hard Memory Controller Features
4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals x
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR4 4.2. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR5 4.3. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for LPDDR5 4.4. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for EMIF Calibration Component
4.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR4 x
4.1.1. ref_clk for EMIF 4.1.2. core_init_n for EMIF 4.1.3. usr_async_clk for EMIF 4.1.4. usr_clk for EMIF 4.1.5. usr_rst_n for EMIF 4.1.6. s0_axi4 for EMIF 4.1.7. mem for EMIF 4.1.8. oct for EMIF
4.2. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for DDR5 x
4.2.1. ref_clk for EMIF 4.2.2. core_init_n for EMIF 4.2.3. usr_async_clk for EMIF 4.2.4. usr_clk for EMIF 4.2.5. usr_rst_n for EMIF 4.2.6. s0_axi4 for EMIF 4.2.7. mem for EMIF 4.2.8. i3c for EMIF 4.2.9. mem_lbd for EMIF 4.2.10. mem_lbs for EMIF 4.2.11. oct for EMIF
4.3. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for LPDDR5 x
4.3.1. ref_clk for EMIF 4.3.2. core_init_n for EMIF 4.3.3. usr_async_clk for EMIF 4.3.4. usr_clk for EMIF 4.3.5. usr_rst_n for EMIF 4.3.6. s0_axi4 for EMIF 4.3.7. mem for EMIF 4.3.8. oct for EMIF
4.4. Intel Agilex® 7 M-Series FPGA EMIF IP Interfaces for EMIF Calibration Component x
4.4.1. s0_axi4lite_clk for EMIF 4.4.2. s0_axi4lite_rst_n for EMIF 4.4.3. s0_axi4lite for EMIF
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP x
5.1. Simulation Walkthrough
5.1. Simulation Walkthrough x
5.1.1. Calibration 5.1.2. Simulation Scripts 5.1.3. Functional Simulation with Verilog HDL 5.1.4. Simulating the Design Example
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support x
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 6.3. DDR4 Board Design Guidelines
6.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR4 x
6.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for DDR4 6.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (DDR4) Parameter Descriptions 6.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
6.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 6.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP
6.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
6.2.1.1. Estimating Pin Requirements 6.2.1.2. DIMM Options 6.2.1.3. Maximum Number of Interfaces
6.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
6.2.2.1. OCT 6.2.2.2. PLL
6.2.4. Pin Placements for Intel Agilex® 7 M-Series FPGA DDR4 EMIF IP x
6.2.4.1. Address and Command Pin Placement for DDR4 6.2.4.2. DDR4 Data Width Mapping 6.2.4.3. General Guidelines - DDR4 6.2.4.4. x4 DIMM Implementation 6.2.4.5. Specific Pin Connection Requirements 6.2.4.6. Command and Address Signals 6.2.4.7. Clock Signals 6.2.4.8. Data, Data Strobes, DM/DBI, and Optional ECC Signals
6.3. DDR4 Board Design Guidelines x
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices 6.3.2. General Layout Routing Guidelines 6.3.3. Reference Stackup 6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies 6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies
6.3.1. Terminations for DDR4 with Intel Agilex® 7 M-Series Devices x
6.3.1.1. Dynamic On-Chip Termination (OCT) 6.3.1.2. Dynamic On-Die Termination (ODT) in DDR4 6.3.1.3. Choosing Terminations on Intel Agilex® 7 M-Series FPGA Devices 6.3.1.4. On-Chip Termination Recommendations for Intel Agilex® 7 M-Series FPGA Devices
6.3.4. Intel Agilex® 7 M-Series EMIF-Specific Routing Guidelines for Various DDR4 Topologies x
6.3.4.1. One DIMM per Channel (1DPC) for UDIMM, RDIMM, and SODIMM DDR4 Topologies 6.3.4.2. Skew Matching Guidelines for DIMM Configurations 6.3.4.3. Power Delivery Recommendations for the Memory / DIMM Side
6.3.5. DDR4 Routing Guidelines: Discrete (Component) Topologies x
6.3.5.1. Single Rank x 8 Discrete (Component) Topology 6.3.5.2. Single Rank x 16 Discrete (Component) Topology 6.3.5.3. ADDR/CMD Reference Voltage/RESET Signal Routing Guidelines for Single Rank x 8 and Single Rank x 16 Discrete (Component) Topologies 6.3.5.4. Skew Matching Guidelines for DDR4 Discrete Configurations 6.3.5.5. Power Delivery Recommendations for DDR4 Discrete Configurations 6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
6.3.5.6. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
6.3.5.6.1. DDR4 Byte Lane Swapping 6.3.5.6.2. DDR4 Address and Command and CLK Lane 6.3.5.6.3. DDR4 Interface x8 Data Lane 6.3.5.6.4. DDR4 Interface x4 Data Lane 6.3.5.6.5. Pin Swizzling
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support x
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 7.3. DDR5 Board Design Guidelines
7.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for DDR5 x
7.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for DDR5 7.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (DDR5) Parameter Descriptions 7.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
7.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP 7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines
7.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
7.2.1.1. Estimating Pin Requirements 7.2.1.2. DIMM Options 7.2.1.3. Maximum Number of Interfaces
7.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
7.2.2.1. OCT 7.2.2.2. PLL
7.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
7.2.3.1. General Guidelines - DDR5 7.2.3.2. x4 DIMM Implementation 7.2.3.3. Specific Pin Connection Requirements 7.2.3.4. Command and Address Signals 7.2.3.5. Clock Signals 7.2.3.6. Data, Data Strobes, DM, and Optional ECC Signals
7.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA DDR5 EMIF IP x
7.2.4.1. Address and Command Pin Placement for DDR5 7.2.4.2. DDR5 Data Width Mapping
7.2.5. Intel Agilex® 7 M-Series EMIF Pin Swapping Guidelines x
7.2.5.1. DDR5 Byte Lane Swapping 7.2.5.2. DDR5 Address and Command and CLK Lane 7.2.5.3. DDR5 Interface x8 Data Lane 7.2.5.4. DDR5 Interface x4 Data Lane 7.2.5.5. Pin Swizzling
7.3. DDR5 Board Design Guidelines x
7.3.1. PCB Stack-up and Design Considerations 7.3.2. General Design Considerations 7.3.3. DDR Differential Signals Routing 7.3.4. Ground Plane and Return Path 7.3.5. RDIMM, UDIMM, and SODIMM Break-in Layout Guidelines 7.3.6. DRAM Break-in Layout Guidelines 7.3.7. DDR5 PCB Layout Guidelines 7.3.8. DDR5 Simulation Strategy
7.3.7. DDR5 PCB Layout Guidelines x
7.3.7.1. DDR5 Discrete Component/Memory Down Topology: up to 40-Bit Interface (1 Rank x8 or x16, 2 Rank x8 or x16) 7.3.7.2. Routing Guidelines for DDR5 Memory Down: 1 Rank or 2 Rank (x8 bit or x16 bit) Configurations 7.3.7.3. Routing Guidelines for DDR5 RDIMM, UDIMM, and SODIMM Configurations 7.3.7.4. Example of a DDR5 layout on Intel FPGA Platform Board
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support x
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning 8.3. LPDDR5 Board Design Guidelines
8.1. Intel Agilex 7 M-Series FPGA EMIF IP Parameters for LPDDR5 x
8.1.1. Intel Agilex® 7 FPGA EMIF IP Parameter for LPDDR5 8.1.2. Intel Agilex 7 FPGA EMIF Memory Device Description IP (LPDDR5) Parameter Descriptions 8.1.3. Intel Agilex 7 FPGA EMIF Calibration IP Parameter Descriptions
8.2. Intel Agilex® 7 M-Series FPGA EMIF IP Pin and Resource Planning x
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins 8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources 8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP 8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP
8.2.1. Intel Agilex® 7 M-Series FPGA EMIF IP Interface Pins x
8.2.1.1. Estimating Pin Requirements 8.2.1.2. DIMM Options 8.2.1.3. Maximum Number of Interfaces
8.2.2. Intel Agilex® 7 M-Series FPGA EMIF IP Resources x
8.2.2.1. OCT 8.2.2.2. PLL
8.2.3. Pin Guidelines for Intel Agilex® 7 M-Series FPGA EMIF IP x
8.2.3.1. General Guidelines - LPDDR5 8.2.3.2. Specific Pin Connection Requirements 8.2.3.3. Command and Address Signals 8.2.3.4. Clock Signals
8.2.4. Pin Placements for Intel Agilex 7 M-Series FPGA LPDDR5 EMIF IP x
8.2.4.1. Address and Command Pin Placement for LPDDR5 8.2.4.2. LPDDR5 Data Width Mapping 8.2.4.3. LPDDR5 Byte Lane Swapping
8.3. LPDDR5 Board Design Guidelines x
8.3.1. PCB Stack-up and Design Considerations 8.3.2. General Design Considerations 8.3.3. DDR Differential Signals Routing 8.3.4. Ground Plane and Return Path 8.3.5. DRAM Break-in Layout Guidelines 8.3.6. LPDDR5 PCB Layout Guidelines 8.3.7. LPDDR5 Simulation Strategy
8.3.6. LPDDR5 PCB Layout Guidelines x
8.3.6.1. LPDDR5 Discrete Component/Memory Down Topology (1 Rank or 2 Rank, up to 64 Bit Interface) 8.3.6.2. Supported LPDDR5 Topologies 8.3.6.3. Example of an LPDDR5 Layout on an Intel® FPGA Platform Board
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure x
9.1. Timing Closure 9.2. Optimizing Timing
9.1. Timing Closure x
9.1.1. Timing Analysis
9.1.1. Timing Analysis x
9.1.1.1. PHY or Core
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization x
10.1. Interface Standard 10.2. Bank Management Efficiency 10.3. Data Transfer 10.4. Improving Controller Efficiency
10.4. Improving Controller Efficiency x
10.4.1. Frequency of Operation 10.4.2. Series of Reads or Writes
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging x
11.1. Interface Configuration Performance Issues 11.2. Functional Issue Evaluation 11.3. Timing Issue Characteristics 11.4. Verifying Memory IP Using the Signal Tap Logic Analyzer 11.5. Generating Traffic with the Test Engine IP 11.6. Guidelines for Developing HDL for Traffic Generator 11.7. Debugging with the External Memory Interface Debug Toolkit
11.1. Interface Configuration Performance Issues x
11.1.1. Interface Configuration Bottleneck and Efficiency Issues
11.2. Functional Issue Evaluation x
11.2.1. Intel® IP Memory Model 11.2.2. Vendor Memory Model 11.2.3. Transcript Window Messages
11.3. Timing Issue Characteristics x
11.3.1. Evaluating FPGA Timing Issues 11.3.2. Evaluating External Memory Interface Timing Issues
11.7. Debugging with the External Memory Interface Debug Toolkit x
11.7.1. Prerequisites for Using the EMIF Debug Toolkit 11.7.2. Configuring Your Design to Use the EMIF Debug Toolkit 11.7.3. Launching the EMIF Debug Toolkit 11.7.4. Using the EMIF Debug Toolkit
11.7.4. Using the EMIF Debug Toolkit x
11.7.4.1. Rerunning Calibration 11.7.4.2. Rerunning the Test Engine 11.7.4.3. Saving Debug Print 11.7.4.4. Calibration Reports 11.7.4.5. Driver Margining Tab 11.7.4.6. Pin Delay Settings Tab
1. About the External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP
2. Intel Agilex® 7 M-Series FPGA EMIF IP – Introduction
3. Intel Agilex® 7 M-Series FPGA EMIF IP – Product Architecture
4. Intel Agilex 7 M-Series FPGA EMIF IP – End-User Signals
5. Intel Agilex® 7 M-Series FPGA EMIF IP – Simulating Memory IP
6. Intel Agilex 7 M-Series FPGA EMIF IP – DDR4 Support
7. Intel Agilex® 7 M-Series FPGA EMIF IP – DDR5 Support
8. Intel Agilex 7 M-Series FPGA EMIF IP – LPDDR5 Support
9. Intel Agilex® 7 M-Series FPGA EMIF IP – Timing Closure
10. Intel Agilex® 7 M-Series FPGA EMIF IP – Controller Optimization
11. Intel Agilex® 7 M-Series FPGA EMIF IP – Debugging
12. Document Revision History for External Memory Interfaces Intel Agilex® 7 M-Series FPGA IP User Guide

6.3.5.6.4. DDR4 Interface x4 Data Lane

For DDR4 x4 interfaces, two nibbles must be packed into the same IO12 lane.

Four pins are reserved for DQS_T and DQS_C signals and the remaining eight pins implement the DQ signals. The IO12 lane is divided into upper and lower halves to accommodate each nibble. You cannot swap signals belonging to one nibble with signals belonging to the other nibble. DQ signals within a nibble swap group may be swapped with each other. You may also swap entire nibbles—that is, nibble 0 and nibble 1—with each other provided the DQS pin functionality transfers to the correct pin locations. However, this process is not recommended for JEDEC-compliant DIMM interfaces, as it prohibits the interoperability between DIMMs constructed with x4 components and DIMMs constructed with x8 components.

The following table lists the supported pin functionality in x4 mode and the pins that may be swapped with each other. Pins belonging to the same swap group may be freely interchanged with each other.

Table 97.  Pin Swapping Rules for DDR4 x4
Pin Index Within Byte Lane DDR4 x4 Data Lane Function Swap Consideration
0 DQ Pin (lower nibble) Swap group A Nibble 0
1 DQ Pin (lower nibble) Swap group A
2 DQ Pin (lower nibble) Swap group A
3 DQ Pin (lower nibble) Swap group A
4 DQS_T Pin (lower nibble) Fixed location (not swappable)
5 DQS_C Pin (lower nibble) Fixed location (not swappable)
6 DQS_T Pin (upper nibble) Fixed location (not swappable) Nibble 1
7 DQS_C Pin (upper nibble) Fixed location (not swappable)
8 DQ Pin (upper nibble) Swap group B
9 DQ Pin (upper nibble) Swap group B
10 DQ Pin (upper nibble) Swap group B
11 DQ Pin (upper nibble) Swap group B
  • Nibble 1 must correspond to DQS[17:9] on a physical JEDEC-compliant DIMM for x4/x8 interoperability.
  • Nibbles 0 and 1 must follow the same skew matching rules among all 12 signals in the IO12 lane as are specified for a x8-based DQS group.
Note:
  • Although the current version of the Intel® Quartus® Prime software may not enforce all of the rules listed in the above table, be aware that all of these rules may be enforced in later versions of the software.
  • At present, the Intel® Quartus® Prime software checks the following:
    • Address and command pin placement, per the table in the Address and Command Pin Placement for DDR4 topic, or the Intel Agilex® 7 External Memory Interface Pin Information file, which is available here: Pin-Out Files for Intel FPGA Devices.
    • For x8, the Intel® Quartus® Prime software checks the following:
      • DQS T/C are on pin index 4 and pin index 5 in a byte lane.
      • DM/DBI is on pin index 6.
      • DQ[x] are on pin indices [11:8] and [3:0].
    • For x4, the Intel® Quartus® Prime software checks the following:
      • DQS T/C on pin index 4 and pin index 5 and associated DQs are within the corresponding byte lane.
      • DQS T/C on pin index 6 and pin index 7 and associated DQs are within the corresponding byte lane.
      You are responsible for ensuring that these conditions are met.
  • The Intel® Quartus® Prime software does not currently check whether DQ pins associated with the lower nibble DQS are actually placed in pin[3:0] or whether DQ pins associated with the upper nibble DQS are actually placed in pin[11:8].

Level Two Title