Visible to Intel only — GUID: rpu1484051789020
Ixiasoft
1. Logic Elements and Logic Array Blocks in Intel® Cyclone® 10 LP Devices
2. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices
3. Embedded Multipliers in Intel® Cyclone® 10 LP Devices
4. Clock Networks and PLLs in Intel® Cyclone® 10 LP Devices
5. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices
6. Configuration and Remote System Upgrades
7. SEU Mitigation in Intel® Cyclone® 10 LP Devices
8. JTAG Boundary-Scan Testing for Intel® Cyclone® 10 LP Devices
9. Power Management in Intel® Cyclone® 10 LP Devices
2.1. Embedded Memory Capacity
2.2. Intel® Cyclone® 10 LP Embedded Memory General Features
2.3. Intel® Cyclone® 10 LP Embedded Memory Operation Modes
2.4. Intel® Cyclone® 10 LP Embedded Memory Clock Modes
2.5. Intel® Cyclone® 10 LP Embedded Memory Configurations
2.6. Intel® Cyclone® 10 LP Embedded Memory Design Consideration
2.7. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices Revision History
4.2.1. PLL Features
4.2.2. PLL Architecture
4.2.3. External Clock Outputs
4.2.4. Clock Feedback Modes
4.2.5. Clock Multiplication and Division
4.2.6. Post-Scale Counter Cascading
4.2.7. Programmable Duty Cycle
4.2.8. PLL Control Signals
4.2.9. Clock Switchover
4.2.10. Programmable Bandwidth
4.2.11. Programmable Phase Shift
4.2.12. PLL Cascading
4.2.13. PLL Reconfiguration
4.2.14. Spread-Spectrum Clocking
5.1. Intel® Cyclone® 10 LP I/O Standards Support
5.2. I/O Resources in Intel® Cyclone® 10 LP Devices
5.3. Intel FPGA I/O IP Cores for Intel® Cyclone® 10 LP Devices
5.4. Intel® Cyclone® 10 LP I/O Elements
5.5. Intel® Cyclone® 10 LP Clock Pins Input Support
5.6. Programmable IOE Features in Intel® Cyclone® 10 LP Devices
5.7. I/O Standards Termination
5.8. Intel® Cyclone® 10 LP High-Speed Differential I/Os and SERDES
5.9. Using the I/Os and High Speed I/Os in Intel® Cyclone® 10 LP Devices
5.10. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices Revision History
5.8.2.1. LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.2. Bus LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.3. RSDS, Mini-LVDS, and PPDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.4. LVPECL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.5. Differential SSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.6. Differential HSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.9.1. Guideline: Validate Your Pin Placement
5.9.2. Guideline: Check for Illegal Pad Placements
5.9.3. Guideline: Voltage-Referenced I/O Standards Restriction
5.9.4. Guideline: Simultaneous Usage of Multiple I/O Standards
5.9.5. Guideline: LVTTL or LVCMOS Inputs in Intel® Cyclone® 10 LP Devices
5.9.6. Guideline: Differential Pad Placement
5.9.7. Guideline: Board Design for Signal Quality
6.1.4.1. Configuring Intel® Cyclone® 10 LP Devices with the JRunner Software Driver
6.1.4.2. Configuring Intel® Cyclone® 10 LP Devices with Jam STAPL
6.1.4.3. JTAG Single-Device Configuration
6.1.4.4. JTAG Multi-Device Configuration
6.1.4.5. Combining JTAG and AS Configuration Schemes
6.1.4.6. Programming Serial Configuration Devices In-System with the JTAG Interface
6.1.4.7. JTAG Instructions
Visible to Intel only — GUID: rpu1484051789020
Ixiasoft
6.1.1.3.2. Single .sof File
This method configures both the master device and slave devices with the same .sof.
Figure 86. Devices Receiving the Same Data with a Single .sof File in Multi-Device AS Configuration
The serial configuration device stores one copy of the .sof. You must set up one or more slave devices in the chain. In this setup, all the Intel® Cyclone® 10 LP devices in the chain are connected for concurrent configuration. This reduces the AS configuration time because all the Intel® Cyclone® 10 LP devices are configured in one configuration cycle.
- Connect the nCE input pins of all the Intel® Cyclone® 10 LP devices to GND.
- Leave the nCEO output pins on all the Intel® Cyclone® 10 LP devices unconnected or use the nCEO output pins as normal user I/O pins.
- You must set the master device in AS mode and the slave devices in PS mode.
- The DATA and DCLK pins are connected in parallel to all the Intel® Cyclone® 10 LP devices.
Intel recommends putting a buffer before the DATA and DCLK outputs from the master device to avoid signal strength and signal integrity issues.
- The buffer should not significantly change the DATA-to-DCLK relationships or delay them with respect to other AS signals (ASDI and nCS).
- The buffer must only drive the slave devices to ensure that the timing between the master device and the serial configuration device is unaffected.