Visible to Intel only — GUID: zwm1489178541953
Ixiasoft
1. Logic Elements and Logic Array Blocks in Intel® Cyclone® 10 LP Devices
2. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices
3. Embedded Multipliers in Intel® Cyclone® 10 LP Devices
4. Clock Networks and PLLs in Intel® Cyclone® 10 LP Devices
5. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices
6. Configuration and Remote System Upgrades
7. SEU Mitigation in Intel® Cyclone® 10 LP Devices
8. JTAG Boundary-Scan Testing for Intel® Cyclone® 10 LP Devices
9. Power Management in Intel® Cyclone® 10 LP Devices
2.1. Embedded Memory Capacity
2.2. Intel® Cyclone® 10 LP Embedded Memory General Features
2.3. Intel® Cyclone® 10 LP Embedded Memory Operation Modes
2.4. Intel® Cyclone® 10 LP Embedded Memory Clock Modes
2.5. Intel® Cyclone® 10 LP Embedded Memory Configurations
2.6. Intel® Cyclone® 10 LP Embedded Memory Design Consideration
2.7. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices Revision History
4.2.1. PLL Features
4.2.2. PLL Architecture
4.2.3. External Clock Outputs
4.2.4. Clock Feedback Modes
4.2.5. Clock Multiplication and Division
4.2.6. Post-Scale Counter Cascading
4.2.7. Programmable Duty Cycle
4.2.8. PLL Control Signals
4.2.9. Clock Switchover
4.2.10. Programmable Bandwidth
4.2.11. Programmable Phase Shift
4.2.12. PLL Cascading
4.2.13. PLL Reconfiguration
4.2.14. Spread-Spectrum Clocking
5.1. Intel® Cyclone® 10 LP I/O Standards Support
5.2. I/O Resources in Intel® Cyclone® 10 LP Devices
5.3. Intel FPGA I/O IP Cores for Intel® Cyclone® 10 LP Devices
5.4. Intel® Cyclone® 10 LP I/O Elements
5.5. Intel® Cyclone® 10 LP Clock Pins Input Support
5.6. Programmable IOE Features in Intel® Cyclone® 10 LP Devices
5.7. I/O Standards Termination
5.8. Intel® Cyclone® 10 LP High-Speed Differential I/Os and SERDES
5.9. Using the I/Os and High Speed I/Os in Intel® Cyclone® 10 LP Devices
5.10. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices Revision History
5.8.2.1. LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.2. Bus LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.3. RSDS, Mini-LVDS, and PPDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.4. LVPECL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.5. Differential SSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.6. Differential HSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.9.1. Guideline: Validate Your Pin Placement
5.9.2. Guideline: Check for Illegal Pad Placements
5.9.3. Guideline: Voltage-Referenced I/O Standards Restriction
5.9.4. Guideline: Simultaneous Usage of Multiple I/O Standards
5.9.5. Guideline: LVTTL or LVCMOS Inputs in Intel® Cyclone® 10 LP Devices
5.9.6. Guideline: Differential Pad Placement
5.9.7. Guideline: Board Design for Signal Quality
6.1.4.1. Configuring Intel® Cyclone® 10 LP Devices with the JRunner Software Driver
6.1.4.2. Configuring Intel® Cyclone® 10 LP Devices with Jam STAPL
6.1.4.3. JTAG Single-Device Configuration
6.1.4.4. JTAG Multi-Device Configuration
6.1.4.5. Combining JTAG and AS Configuration Schemes
6.1.4.6. Programming Serial Configuration Devices In-System with the JTAG Interface
6.1.4.7. JTAG Instructions
Visible to Intel only — GUID: zwm1489178541953
Ixiasoft
5.9.4. Guideline: Simultaneous Usage of Multiple I/O Standards
Each Intel® Cyclone® 10 LP I/O bank has its own VCCIO pins and supports only one VCCIO of 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.0 V, or 3.3 V. An I/O bank can simultaneously support several I/O standards if the I/O standards use the same VCCIO levels for input and output pins.
An I/O bank can simultaneously support several voltage-referenced standards if all the I/O standards use the same VREF and VCCIO values. For example, For examples:
- SSTL-2 and SSTL-18 I/O standards require different VREF values. If you implement both of these I/O standards in the device, you must assign them to I/O pins in different I/O banks.
- If you implement SSTL-2 and 2.5 V LVCMOS I/O standards, both with VCCIO of 2.5 V and VREF of 1.25 V, you can assign them to I/O pins in the same I/O bank.