Visible to Intel only — GUID: pve1490158146388
Ixiasoft
1. Logic Elements and Logic Array Blocks in Intel® Cyclone® 10 LP Devices
2. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices
3. Embedded Multipliers in Intel® Cyclone® 10 LP Devices
4. Clock Networks and PLLs in Intel® Cyclone® 10 LP Devices
5. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices
6. Configuration and Remote System Upgrades
7. SEU Mitigation in Intel® Cyclone® 10 LP Devices
8. JTAG Boundary-Scan Testing for Intel® Cyclone® 10 LP Devices
9. Power Management in Intel® Cyclone® 10 LP Devices
2.1. Embedded Memory Capacity
2.2. Intel® Cyclone® 10 LP Embedded Memory General Features
2.3. Intel® Cyclone® 10 LP Embedded Memory Operation Modes
2.4. Intel® Cyclone® 10 LP Embedded Memory Clock Modes
2.5. Intel® Cyclone® 10 LP Embedded Memory Configurations
2.6. Intel® Cyclone® 10 LP Embedded Memory Design Consideration
2.7. Embedded Memory Blocks in Intel® Cyclone® 10 LP Devices Revision History
4.2.1. PLL Features
4.2.2. PLL Architecture
4.2.3. External Clock Outputs
4.2.4. Clock Feedback Modes
4.2.5. Clock Multiplication and Division
4.2.6. Post-Scale Counter Cascading
4.2.7. Programmable Duty Cycle
4.2.8. PLL Control Signals
4.2.9. Clock Switchover
4.2.10. Programmable Bandwidth
4.2.11. Programmable Phase Shift
4.2.12. PLL Cascading
4.2.13. PLL Reconfiguration
4.2.14. Spread-Spectrum Clocking
5.1. Intel® Cyclone® 10 LP I/O Standards Support
5.2. I/O Resources in Intel® Cyclone® 10 LP Devices
5.3. Intel FPGA I/O IP Cores for Intel® Cyclone® 10 LP Devices
5.4. Intel® Cyclone® 10 LP I/O Elements
5.5. Intel® Cyclone® 10 LP Clock Pins Input Support
5.6. Programmable IOE Features in Intel® Cyclone® 10 LP Devices
5.7. I/O Standards Termination
5.8. Intel® Cyclone® 10 LP High-Speed Differential I/Os and SERDES
5.9. Using the I/Os and High Speed I/Os in Intel® Cyclone® 10 LP Devices
5.10. I/O and High Speed I/O in Intel® Cyclone® 10 LP Devices Revision History
5.8.2.1. LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.2. Bus LVDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.3. RSDS, Mini-LVDS, and PPDS I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.4. LVPECL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.5. Differential SSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.8.2.6. Differential HSTL I/O Standard in Intel® Cyclone® 10 LP Devices
5.9.1. Guideline: Validate Your Pin Placement
5.9.2. Guideline: Check for Illegal Pad Placements
5.9.3. Guideline: Voltage-Referenced I/O Standards Restriction
5.9.4. Guideline: Simultaneous Usage of Multiple I/O Standards
5.9.5. Guideline: LVTTL or LVCMOS Inputs in Intel® Cyclone® 10 LP Devices
5.9.6. Guideline: Differential Pad Placement
5.9.7. Guideline: Board Design for Signal Quality
6.1.4.1. Configuring Intel® Cyclone® 10 LP Devices with the JRunner Software Driver
6.1.4.2. Configuring Intel® Cyclone® 10 LP Devices with Jam STAPL
6.1.4.3. JTAG Single-Device Configuration
6.1.4.4. JTAG Multi-Device Configuration
6.1.4.5. Combining JTAG and AS Configuration Schemes
6.1.4.6. Programming Serial Configuration Devices In-System with the JTAG Interface
6.1.4.7. JTAG Instructions
Visible to Intel only — GUID: pve1490158146388
Ixiasoft
4.2.13.1.2. Scan Chain
The Intel® Cyclone® 10 LP PLLs have a 144-bit scan chain.
Block Name | Number of Bits | ||
---|---|---|---|
Counter | Other | Total | |
C4 11 | 16 | 2 12 | 18 |
C3 | 16 | 2 12 | 18 |
C2 | 16 | 2 12 | 18 |
C1 | 16 | 2 12 | 18 |
C0 | 16 | 2 12 | 18 |
M | 16 | 2 12 | 18 |
N | 16 | 2 12 | 18 |
Charge Pump | 9 | 0 | 9 |
Loop Filter13 | 9 | 0 | 9 |
Total number of bits | 144 |
Figure 57. PLL Component Scan Chain Order
Figure 58. PLL Post-Scale Counter Scan Chain Bit Order
11 LSB bit for C4 low-count value is the first bit shifted into the scan chain.
12 These two control bits include rbypass, for bypassing the counter, and rselodd, for selecting the output clock duty cycle.
13 MSB bit for loop filter is the last bit shifted into the scan chain.