Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

Download PDF
ID 683293
Date 8/24/2021
Public
Document Table of Contents
Document Table of Contents x
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide x
1.1. Overview 1.2. PDN Decoupling Methodology Review 1.3. PDN Tool Setup and Result Optimization 1.4. Device-Specific PDN Tool 2.0 Known Issues and Their Solutions 1.5. Document Revision History for the Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide
1.2. PDN Decoupling Methodology Review x
1.2.1. PDN Circuit Topology 1.2.2. Major Tabs of the PDN Tool 2.0 1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 1.2.4. Troubleshooting ZEFF
1.2.1. PDN Circuit Topology x
1.2.1.1. ZTARGET 1.2.1.2. FEFFECTIVE
1.2.2. Major Tabs of the PDN Tool 2.0 x
1.2.2.1. System_Decap 1.2.2.2. Stackup 1.2.2.3. BGA_Via 1.2.2.4. Plane_Cap 1.2.2.5. Cap_Mount 1.2.2.6. X2Y_Mount 1.2.2.7. Library 1.2.2.8. Enlarged_Graph
1.2.2.1. System_Decap x
1.2.2.1.1. Device Selection Section 1.2.2.1.2. Power Rail Data and Configuration Section 1.2.2.1.3. Meeting Target Impedance when Entering 0 A into the PDN Tool 1.2.2.1.4. Dealing with Multiple Shared Power Supply Pin Types 1.2.2.1.5. VRM Data Section 1.2.2.1.6. Rail Group Summary Section 1.2.2.1.7. VRM Impedance Section 1.2.2.1.8. BGA Via Section 1.2.2.1.9. Plane Section 1.2.2.1.10. Spreading Section 1.2.2.1.11. Implementing Split Planes 1.2.2.1.12. FEFFECTIVE Section 1.2.2.1.13. Decoupling Section 1.2.2.1.14. Results Summary Section 1.2.2.1.15. Recommended Flow for Deriving Decoupling for an FPGA System using the System_Decap Tab
1.2.2.2. Stackup x
1.2.2.2.1. Stackup Data 1.2.2.2.2. Full Stackup
1.2.2.7. Library x
1.2.2.7.1. Two-Terminal Decoupling Capacitors 1.2.2.7.2. Bulk Capacitors 1.2.2.7.3. X2Y Decoupling Capacitors 1.2.2.7.4. BGA Via and Plane Capacitance 1.2.2.7.5. VRM Library 1.2.2.7.6. Spreading R and L Parasitics 1.2.2.7.7. Dielectric Material Library 1.2.2.7.8. User Set FEFFECTIVE
1.2.3. Design PCB Decoupling Using the PDN Tool 2.0 x
1.2.3.1. Pre-Layout Instructions 1.2.3.2. Deriving Decoupling in a Single-Rail Scenario 1.2.3.3. Deriving Decoupling in the Power-Sharing Scenarios
1.2.4. Troubleshooting ZEFF x
1.2.4.1. Strategies for Correcting a High ZEFF
1.3. PDN Tool Setup and Result Optimization x
1.3.1. Setting Up a PCB Stackup 1.3.2. Setting up a Power Group 1.3.3. Optimizing in Pre-Layout 1.3.4. Further Optimizing for Better Accuracy 1.3.5. Correlation
1.3.1. Setting Up a PCB Stackup x
1.3.1.1. Selecting Your Device 1.3.1.2. Inputting Stackup Data
1.3.1.2. Inputting Stackup Data x
1.3.1.2.1. Using a Custom Dielectric Material
1.3.2. Setting up a Power Group x
1.3.2.1. Selecting the Rails 1.3.2.2. Rail Group Summary 1.3.2.3. VRM Impedance 1.3.2.4. BGA Via 1.3.2.5. Calculating Plane 1.3.2.6. Plane Spreading Parasitics 1.3.2.7. FEFFECTIVE and Decoupling Result Summary
1.3.3. Optimizing in Pre-Layout x
1.3.3.1. Checking the Capacitor Model 1.3.3.2. Optimizing the Decap Count
1. Device-Specific Power Delivery Network (PDN) Tool 2.0 User Guide

1.2.1. PDN Circuit Topology

The PDN tool 2.0 is based on a lumped equivalent model representation of the power delivery network topology.

Figure 1. PDN Topology Modeled as Part of the Tool The PDN impedance profile is the impedance-over-frequency looking outward from the device.

For a first order analysis, the VRM can be simply modeled as a series-connected resistor and inductor as shown above. This is a result of the typical proportional, integral, derivative (PID) voltage regulation loop compensation configuration of many regulators. The VRM has a very low impedance and can respond to the instantaneous current requirements of the FPGA up to between 50 kHz and 150 kHz, depending on the voltage regulation loop crossover (0 dB) frequency.

The equivalent series resistance (ESR) and equivalent series inductance (ESL) values can be obtained from the VRM manufacturer. At higher frequencies, the VRM impedance is primarily inductive, making it incapable of meeting the transient current requirement.

PCB decoupling capacitors are used for reducing the PDN impedance up to 50-100 MHz. The on-board discrete decoupling capacitors provide the required low impedance. This depends on the capacitor-intrinsic parasitics (RcN, CcN, LcN) and the capacitor mounting inductance (LmntN). The inter-planar capacitance between the power-ground planes typically has lower inductance than the discrete decoupling capacitor network, making it more effective at higher frequencies up to 100 MHz. As frequency increases, the PCB decoupling capacitors become less effective. The limitation comes from the parasitic inductance seen with respect to the FPGA. FPGA parasitic inductance includes capacitor mounting inductance, PCB spreading inductance, ball grid array (BGA) via inductance, and packaging parasitic inductance. All of these parasitics are modeled in the PDN tool 2.0 to capture the effect of the PCB decoupling capacitors accurately. To simplify the circuit topology, all parasitics are represented with lumped inductors and resistors despite the distributed nature of PCB spreading inductance.

Level Two Title