Intel® Stratix® 10 DX FPGA Development Kit User Guide

Download PDF
ID 683561
Date 9/25/2023
Public
Document Table of Contents
Document Table of Contents x
1. Getting Started 2. Development Kit Overview 3. Power Up the Development Kit 4. Board Test System (BTS) 5. Development Kit Hardware and Configuration 6. Document Revision History for Intel® Stratix® 10 DX FPGA Development Kit User Guide A. Development Kit Components B. Safety and Regulatory Information C. Compliance and Conformity Information
1. Getting Started x
1.1. About this Document 1.2. Installing the Intel® Quartus® Prime Pro Edition Software 1.3. Downloading the Board Package 1.4. Installing the Driver for Intel FPGA Download Cable II
1.2. Installing the Intel® Quartus® Prime Pro Edition Software x
1.2.1. Activating Your License
2. Development Kit Overview x
2.1. Supported Features 2.2. Recommended Operating Conditions 2.3. Handling the Board
3. Power Up the Development Kit x
3.1. Default Switch Settings 3.2. Connectors and LEDs 3.3. Performing Board Restore through Board Test System (BTS) 3.4. Controlling On-board Clock
4. Board Test System (BTS) x
4.1. Preparing the Development Kit 4.2. Running the Board Test System 4.3. Using the Board Test System 4.4. Smart VID Setting
4.3. Using the Board Test System x
4.3.1. Configure Menu 4.3.2. Sys Info Tab 4.3.3. GPIO Tab 4.3.4. QSFP Tab 4.3.5. Component DDR4 CH0 Tab 4.3.6. Component DDR4 CH1 Tab 4.3.7. DDR4 DIMM CH0 Tab 4.3.8. DDR4 DIMM CH1 Tab 4.3.9. Power Monitor 4.3.10. Clock Controller
5. Development Kit Hardware and Configuration x
5.1. FPGA Configuration 5.2. Programming the FPGA Over Intel® FPGA Download Cable 5.3. Configuration Modes
5.3. Configuration Modes x
5.3.1. Avalon® Streaming Interface x8 Mode 5.3.2. JTAG Mode
5.3.1. Avalon® Streaming Interface x8 Mode x
Avalon® Streaming Interface x8 Configuration Guideline
A. Development Kit Components x
A.1. Components Overview A.2. Power, Thermal, and Mechanical Considerations A.3. Clock Circuits A.4. Memory Interface A.5. PCIe Interface A.6. UPI Interface A.7. Transceiver Signals: PCIe and UPI Interface A.8. SlimSAS Connector A.9. QSFP Network Interface A.10. I2C Interface A.11. QSPI Flash Memory
A.2. Power, Thermal, and Mechanical Considerations x
A.2.1. Power Guidelines A.2.2. Thermal Requirements A.2.3. Mechanical Requirements
A.2.1. Power Guidelines x
A.2.1.1. Power Distribution A.2.1.2. Power Sequence A.2.1.3. Power Measurement
A.2.2. Thermal Requirements x
A.2.2.1. Operating Conditions A.2.2.2. Temperature Monitoring
A.9. QSFP Network Interface x
A.9.1. Dual Port Controller
A.11. QSPI Flash Memory x
A.11.1. Configuration QSPI Flash Memory A.11.2. NIOS QSPI Flash Memory
B. Safety and Regulatory Information x
B.1. Safety Warnings B.2. Safety Cautions
1. Getting Started
2. Development Kit Overview
3. Power Up the Development Kit
4. Board Test System (BTS)
5. Development Kit Hardware and Configuration
6. Document Revision History for Intel® Stratix® 10 DX FPGA Development Kit User Guide
A. Development Kit Components
B. Safety and Regulatory Information
C. Compliance and Conformity Information

A.2.1. Power Guidelines

This section describes the power supply for Intel® Stratix® 10 DX FPGA Development Kit.

A laptop-style DC power supply is provided with the development kit. Use only the supplied power supply. The power supply has an auto-sensing input voltage of 100-240 V AC power and will output 12 V DC power at 20 A to the development board. The 12 V DC input power is then stepped down to various power rails used by the board components.

An on-board multi-channel analog-to-digital converter (ADC) measures both the voltage and current for several specific board rails. The power utilization is displayed on a graphical user interface (GUI) that can graph power consumption versus time.

The Intel® Stratix® 10 DX FPGA Development Kit has two modes of operation:
  • Standard PCIe compliant system
    In this mode, plug the board into an available PCI Express slot and connect the standard 2x4 power cords available from the PC's ATX power supply to J11 on the board. The PCIe slot together with the auxiliary PCIe power cords are required to power the entire board. If you do not connect the 2x4 auxiliary power connection, the board does not power on. The power switch SW3 is ignored when the board is used in the PCIe system.
    Figure 32. Setup Example
  • Standalone evaluation board powered by included power supply
    In this mode, plug the included power supply into the 2x4 pin connector (J42) and the AC power cord of the power supply into a power outlet. This power supply provides the entire power to the board without the need to obtain power from the PCIe slot. The power switch SW31 controls powering of the board.
    Figure 33. Setup Example

Section Content
Power Distribution
Power Sequence
Power Measurement

Level Two Title