Agilex™ 7 FPGA I-Series Development Kit User Guide

Download PDF
ID 683288
Date 5/31/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide A. Development Kits Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Box Contents 1.3. Operating Conditions
2. Getting Started x
2.1. About Quartus® Prime Software 2.2. Development Board Package 2.3. Installing the Intel® FPGA Download Cable II Driver
2.1. About Quartus® Prime Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Development Board 3.2. Default Switch Settings 3.3. How to Generate a POF Image to Program the Flash 3.4. How to Program the Generated POF Image 3.5. The Required SmartVID QSF Assignments to Compile a Design
3.2. Default Switch Settings x
3.2.1. Default Settings 3.2.2. Perform Board Restore through Quartus® Prime Programmer
4. Board Test System x
4.1. Set Up BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control On-board Clock through Clock Controller GUI 4.4. Monitor On-board Power through Power Monitor GUI 4.5. BTS Test Areas 4.6. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up BTS GUI Running Environment x
4.1.1. Download OpenJDK 4.1.2. Download OpenJFX 4.1.3. Install OpenJDK and OpenJFX 4.1.4. Run BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Info Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab 4.2.6. The RAM Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab
A. Development Kits Components x
A.1. Board Overview A.2. Agilex™ 7 FPGA I-Series A.3. PCIe* and CXL Interfaces A.4. MCIO Connector A.5. MCIO Cable Assembly Information A.6. Network Interfaces A.7. Port Controller A.8. FPGA Configuration A.9. Supported Configuration Modes A.10. Memory Interfaces A.11. I2C A.12. Clock Circuits A.13. System Power A.14. Temperature Monitoring A.15. Mechanical Requirements A.16. Board Thermal Requirements A.17. Board Operating Conditions A.18. Over Temperature Warning LED
A.13. System Power x
A.13.1. Power Guidelines A.13.2. Power Distribution System A.13.3. Power Sequence A.13.4. Power Measurement
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide
A. Development Kits Components
B. Additional Information

A.1. Board Overview

Images of the Agilex™ 7 FPGA I-Series development board are shown below.
Figure 32.  Agilex™ 7 FPGA I-Series Development Board Image—FrontFor DK-DEV-AGI027RES and DK-DEV-AGI027R1BES.
Figure 33.  Agilex™ 7 FPGA I-Series Development Board Image—FrontFor DK-DEV-AGI027RBES and DK-DEV-AGI027-RA.
Figure 34.  Agilex™ 7 FPGA I-Series Development Board Image—BackFor DK-DEV-AGI027RES and DK-DEV-AGI027R1BES
Figure 35.  Agilex™ 7 FPGA I-Series Development Board Image—BackFor DK-DEV-AGI027RBES and DK-DEV-AGI027-RA.
Level Two Title