Agilex™ 7 FPGA I-Series Development Kit User Guide

Download PDF
ID 683288
Date 5/31/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide A. Development Kits Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Box Contents 1.3. Operating Conditions
2. Getting Started x
2.1. About Quartus® Prime Software 2.2. Development Board Package 2.3. Installing the Intel® FPGA Download Cable II Driver
2.1. About Quartus® Prime Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Development Board 3.2. Default Switch Settings 3.3. How to Generate a POF Image to Program the Flash 3.4. How to Program the Generated POF Image 3.5. The Required SmartVID QSF Assignments to Compile a Design
3.2. Default Switch Settings x
3.2.1. Default Settings 3.2.2. Perform Board Restore through Quartus® Prime Programmer
4. Board Test System x
4.1. Set Up BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control On-board Clock through Clock Controller GUI 4.4. Monitor On-board Power through Power Monitor GUI 4.5. BTS Test Areas 4.6. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up BTS GUI Running Environment x
4.1.1. Download OpenJDK 4.1.2. Download OpenJFX 4.1.3. Install OpenJDK and OpenJFX 4.1.4. Run BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Info Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab 4.2.6. The RAM Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab
A. Development Kits Components x
A.1. Board Overview A.2. Agilex™ 7 FPGA I-Series A.3. PCIe* and CXL Interfaces A.4. MCIO Connector A.5. MCIO Cable Assembly Information A.6. Network Interfaces A.7. Port Controller A.8. FPGA Configuration A.9. Supported Configuration Modes A.10. Memory Interfaces A.11. I2C A.12. Clock Circuits A.13. System Power A.14. Temperature Monitoring A.15. Mechanical Requirements A.16. Board Thermal Requirements A.17. Board Operating Conditions A.18. Over Temperature Warning LED
A.13. System Power x
A.13.1. Power Guidelines A.13.2. Power Distribution System A.13.3. Power Sequence A.13.4. Power Measurement
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide
A. Development Kits Components
B. Additional Information

4.2.1. The Bottom Info Bar

The bottom information bar shows the status of the system connection, Quartus® Prime version, and the JTAG clock speed.

  • System Connected/Disconnected: Shows if the board is connected to the system. The green sign turns gray if the board becomes disconnected.
  • Quartus® Prime Version: Displays the current Quartus® Prime version installed and active on your system. The text turns red if your version is older than the required version. Change the QUARTUS_ROOTDIR environment variable if you have installed the right version but the active version does not meet the requirement.
  • JTAG: Displays the JTAG clock frequency.
Level Two Title