Intel Cyclone 10 LP Device Design Guidelines

Download PDF
ID 683861
Date 3/28/2019
Public
Document Table of Contents
Document Table of Contents x
Intel® Cyclone® 10 LP Device Design Guidelines
Intel® Cyclone® 10 LP Device Design Guidelines x
Design Flow System Specification Device Selection Early System and Board Planning Pin Connection Considerations for Board Design I/O and Clock Planning Design Entry Design Implementation, Analysis, Optimization, and Verification Document Revision History for Intel® Cyclone® 10 LP Device Design Guidelines
System Specification x
Design Specifications IP Selection Platform Designer
Device Selection x
Device Variant PLLs and Clock Routing Logic, Memory, and Multiplier Density I/O Pin Count, LVDS Channels, and Package Offering Speed Grade Vertical Device Migration
Early System and Board Planning x
Early Power Estimation Planning for Device Configuration Planning for On-chip Debugging
Planning for Device Configuration x
Configuration Scheme Selection Configuration Features Intel® Quartus® Prime Configuration Settings
Configuration Scheme Selection x
Serial Configuration Devices Download Cables
Intel® Quartus® Prime Configuration Settings x
Optional Configuration Pins
Planning for On-chip Debugging x
On-chip Debugging Tools Planning Guidelines for Debugging Tools
Pin Connection Considerations for Board Design x
Device Power-Up Power Pin Connections and Power Supplies Configuration Pin Connections Board-related Intel® Quartus® Prime Settings Signal Integrity Considerations Board-level Simulation and Advanced I/O Timing Analysis
Power Pin Connections and Power Supplies x
Decoupling Capacitors PLL Board Design Guidelines
Configuration Pin Connections x
Clock Trace Signal Integrity JTAG Pins MSEL Configuration Mode Pins Other Configuration Pins
JTAG Pins x
JTAG Pin Connections Download Cable Operating Voltage JTAG Signal Buffering
Board-related Intel® Quartus® Prime Settings x
Device-wide Output Enable Pin Unused Pins
Signal Integrity Considerations x
Voltage Reference Pins Simultaneous Switching Noise I/O Termination
I/O and Clock Planning x
Making FPGA Pin Assignments Early Pin Planning and I/O Assignment Analysis I/O Features and Pin Connections Clock and PLL Selection PLL Feature Guidelines Clock Control Features I/O Simultaneous Switching Noise
I/O Features and Pin Connections x
I/O Signaling Type Selectable Standards and Flexible I/O Banks Dual-Purpose and Special Pin Connections Intel® Cyclone® 10 LP I/O Features
PLL Feature Guidelines x
Clock Feedback Mode Clock Outputs
Design Entry x
Design Recommendations Using IP Cores Recommended HDL Coding Styles Register Power-up Levels and Control Signals
Design Implementation, Analysis, Optimization, and Verification x
Selecting a Synthesis Tool Device Resource Utilization Reports Intel® Quartus® Prime Messages Timing Constraints and Analysis Area and Timing Optimization Preserving Performance and Reducing Compilation Time Simulation Power Analysis Power Optimization
Timing Constraints and Analysis x
Recommended Timing Optimization and Analysis Assignments
Power Optimization x
Device and Design Power Optimization Techniques Intel® Quartus® Prime Power Optimization Techniques
Device and Design Power Optimization Techniques x
Clock Power Management Memory Power Reduction I/O Power Guidelines
Intel® Cyclone® 10 LP Device Design Guidelines

Serial Configuration Devices

Table 14.  Serial Configuration Devices Checklist
Number Done? Checklist Item
1   If you want to use the AS configuration mode with large device densities, confirm there is a configuration device available that is large enough for your target FPGA density.

Serial configuration devices can be programmed using an Intel FPGA Download Cable or Intel FPGA Ethernet Cable with the Intel® Quartus® Prime Standard Edition software through the active serial interface.

Alternatively, you can use supported third-party programmers such as BP Microsystems and System General, or a microprocessor with the SRunner software driver. SRunner is a software driver developed for embedded serial configuration device programming that designers can customize to fit in different embedded systems.

Serial configuration devices do not directly support the JTAG interface; however, you can program the device with JTAG download cables using the Intel® Cyclone® 10 LP FPGA as a bridge between the JTAG interface and the configuration device, allowing both devices to use the same JTAG interface.

Level Two Title