Stratix® 10 SX SoC Development Kit User Guide

Download PDF
ID 683303
Date 6/06/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Document Revision History for the Stratix® 10 10 SX SoC Development Kit User Guide
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. Installing Quartus® Prime Software 2.2. Installing the Intel® FPGA Download Cable 2.3. Installing the Intel SoC Embedded Development Suite (EDS) 2.4. Installing the Stratix® 10 SX SoC Development Kit Package
3. Development Kit Setup x
3.1. Inspect the Development Kit 3.2. Default Setup of the Development Kit 3.3. MAX® 10 System Controller Updates
4. Development Kit Components x
4.1. Development Kit Feature Summary 4.2. Board Components 4.3. Stratix® 10 SoC Device Overview 4.4. MAX® 10 System Controller Overview 4.5. FPGA Configuration 4.6. General User Input/Output 4.7. Connectors and Interfaces 4.8. Daughter Cards 4.9. System Memory 4.10. System Power
4.7. Connectors and Interfaces x
4.7.1. PCIe* Slot 4.7.2. ZQSFP+ 4.7.3. SFP+ 4.7.4. HDMI 4.7.5. SDI Port 4.7.6. MXP 4.7.7. Intel® FPGA Download Cable Direct Port (Debug Port) 4.7.8. FMC+ A/B Slot 4.7.9. FMC+ A/B LVDS Interfaces (LPC Pins) 4.7.10. LMK05028 Jitter Attenuator 4.7.11. FPGA-IOMAX10 Interface
4.8. Daughter Cards x
4.8.1. HPS IO-48 OOBE Daughter Card 4.8.2. HPS IO-48 NAND Flash Daughter Card 4.8.3. HPS Boot Flash Card
4.8.3. HPS Boot Flash Card x
4.8.3.1. Boot QSPI Flash Daughter Card 4.8.3.2. Boot MicroSD Daughter Card 4.8.3.3. Boot eMMC Daughter Card
4.9. System Memory x
4.9.1. FPGA Memory (DDR4 SO-DIMM) 4.9.2. HPS Memory (External 4 GB HILO x72 DDR4) 4.9.3. HPS I2C Interface
4.10. System Power x
4.10.1. Power Supply Options 4.10.2. Power Sequence 4.10.3. Power Distribution Network
5. Board Test System x
5.1. Preparing the Board 5.2. Running the BTS 5.3. Using the BTS
5.3. Using the BTS x
5.3.1. The Configure Menu 5.3.2. The GPIO Tab 5.3.3. The QSFP/SFP Tab 5.3.4. The PCIE Tab 5.3.5. The MXP Tab 5.3.6. The FMCA Tab 5.3.7. The FMCB Tab 5.3.8. The DDR4 Tab 5.3.9. Power Monitor 5.3.10. The Clock Control
A. Additional Information x
A.1. Modify the Stratix® 10 SX SoC Development Kit to use a battery for the BBRAM A.2. Modify the Stratix® 10 SX SoC Development Kit HPS DDR4 memory width and ECC configuration using the Golden Hardware Reference Design project A.3. Safety and Regulatory Information A.4. Compliance Information
A.3. Safety and Regulatory Information x
A.3.1. Safety Warnings A.3.2. Safety Cautions
A.4. Compliance Information x
A.4.1. Compliance and Conformity Statements
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Document Revision History for the Stratix® 10 10 SX SoC Development Kit User Guide

3.2. Default Setup of the Development Kit

This development kit ships with its board switches preconfigured to support the design examples in the kit.

  1. Power up the development board by using the included power supply.
  2. When configuration is complete, the configuration done green LED (D22) illuminates, signaling that the Stratix® 10 device is configured successfully.
CAUTION:
Use only the provided power supply. Power regulation circuits on the board can be damaged by power supplies with greater voltage and a lower-rated power supply may not be able to provide enough power for the board.
Table 3.  Default Setup
Checkpoint Name Reference Description
1 Power Switch SW7 Power is turn off at left position.
2 Power Adapter connector J25, J55 Both connectors can be used to connect the power adapter.
3 Intel® Enpirion® J29 You can install Intel® Enpirion® dongle to monitor the board power rails. Switch 8 is at off position.
4 JTAG Dongle connector J1 You can install Intel® JTAG dongle to access FPGA.
5 JTAG Switch SW1 Default Setup from bit 1 to bit 8 is “off, off, on, on, on, on, on, on”: Stratix® 10 SoC and MAX® 10 are on the JTAG chain.
6 USB JTAG Port J57 You need connect Micro USB cable to access Stratix® 10 SoC.
7 12V Fan Connector J16 You need use it to connect thermal fan.
8 Boot Switch SW4

The default setup from bit 1 to bit 4 is “on, off, on, off”.

FPGA/HPS I2C is enabled. Daughter card power is on.

9 MSEL Switch SW2 Default setup is “on on on on”: JTAG mode.
Level Two Title