F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

Download PDF
ID 720998
Date 12/19/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Configuration Registers Overview 7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives 8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide
1. Introduction x
1.1. IP Core Overview 1.2. Release Information 1.3. Device Family Support 1.4. Device Speed Grade Support 1.5. Resource Utilization 1.6. Related Documentation
1.1. IP Core Overview x
1.1.1. Reconfiguration Group 1.1.2. Base Profile 1.1.3. Secondary Profiles 1.1.4. Startup Profile 1.1.5. Supported Reconfiguration Groups
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. TX and RX Parallel and Serial Signals 2.4. Custom Cadence Control and Status Signals 2.5. TX and RX PMA Status Signals 2.6. RS-FEC Signals 2.7. TX and RX PMA FIFO Signals 2.8. PMA Avalon Memory-Mapped Signals 2.9. Datapath Avalon Memory-Mapped Signals
3. Parameters x
3.1. Dynamic Reconfiguration QSF Settings 3.2. QSF settings for Different Reconfiguration Profiles
3.2. QSF settings for Different Reconfiguration Profiles x
3.2.1. Bypass RX Adaptation QSF Settings
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.2. Specifying the IP Core Parameters and Options x
4.2.1. Reference and System PLL Clock for your IP Design
4.4. Configuring the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core x
4.4.1. Steps to Configure the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP Core
6. Configuration Registers Overview x
6.1. Controlling the Reconfiguration Soft CSR Registers for Dynamic Reconfiguration 6.2. Configuration Registers
6.2. Configuration Registers x
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers 6.2.2. F-Tile PMA/FEC Direct PHY Multirate Intel® FPGA IP Core Soft CSR Registers
6.2.1. F-Tile PMA/FEC Direct PHY Intel FPGA IP Core Soft CSR Registers x
6.2.1.1. Controlling the Reconfiguration Soft CSR with Fractures
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Configuration Registers Overview
7. F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide Archives
8. Document Revision History for the F-Tile PMA and FEC Direct PHY Multirate Intel® FPGA IP User Guide

2.1. Clock Signals

The following table describes the clock signals that are a part of the clock interface of the F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP.
Table 7.  TX and RX Reference Clock and Clock Output Interface SignalsRefer to Variables Defining Bits for the Interfacing Ports in Port and Signal Reference for variable definitions.
Signal Name Clocks Domain/Resets Direction Description

rx_clkout_stream<x>

rx_clkout2_stream<x>

tx_clkout_stream<x>

tx_clkout2_stream<x>

N/A Output Output port enabled by default. You can select one of these ports, by selecting TX/RX clock options. These are per stream in F-Tile PMA/FEC Direct PHY Multirate Intel FPGA IP as interfaces in the system mode requires clock signals to be single bit per clock.

coreclkin

N/A Input Core clock that is usually driven by system pll div by 2 clock. All FPGA soft logic uses these clocks.
tx_pll_refclk_link_xcvr<n>_prof<j> N/A Input These clock ports are 1 bit. This is neither physical nor logical port. You connect this to <out_refclk_fgt<x>> port from the F-Tile Reference and System PLL Clocks Intel® FPGA IP. This connection guides Intel® Quartus® Prime Pro Edition software to correctly configure the clock network.
rx_cdr_refclk_link_xcvr<n>_prof<j> N/A Input These clock ports are 1 bit. This is neither physical nor logical port. You connect this to <out_refclk_fgt<x>> port from the F-Tile Reference and System PLL Clocks Intel® FPGA IP. This connection guides Intel® Quartus® Prime Pro Edition software to correctly configure the clock network.
system_pll_clk_link N/A Input This is virtual representation of system PLL output clock. This is neither physical nor logical port. You connect this to <out_systempll_clk_0> port from the F-Tile Reference and System PLL Clocks Intel® FPGA IP. This connection guides Intel® Quartus® Prime Pro Edition software to correctly configure the clock network.
Note: Ports ending in _link must connect to the F-Tile Reference and System PLL Clocks Intel® FPGA IP. These ports cannot be simulated.
Level Two Title