F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

Download PDF
ID 720987
Date 7/08/2024
Public
Document Table of Contents
Document Table of Contents x
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide 2. Quick Start Guide 3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example 4. Interface Signals Description 5. Configuration Registers Description 6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives 7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide x
2.1. Directory Structure 2.2. Generating the Design 2.3. Compiling and Simulating the Design 2.4. Compiling and Testing the Design in Hardware 2.5. Signal Tap Debugging
2.2. Generating the Design x
2.2.1. Procedure 2.2.2. Design Example Parameters
2.3. Compiling and Simulating the Design x
2.3.1. Procedure 2.3.2. Testbench
2.4. Compiling and Testing the Design in Hardware x
2.4.1. Procedure 2.4.2. Hardware Setup
2.5. Signal Tap Debugging x
2.5.1. Signal Tap Debug Signals
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example x
3.1. Features 3.2. Hardware and Software Requirements 3.3. Functional Description 3.4. Simulation 3.5. Hardware Testing 3.6. Interface Signals 3.7. Configuration Registers
3.3. Functional Description x
3.3.1. Design Components 3.3.2. Clocking Scheme 3.3.3. Reset Scheme
3.3.3. Reset Scheme x
3.3.3.1. Reset Sequence
3.3.3.1. Reset Sequence x
3.3.3.1.1. Run-time Reset Sequence—TX 3.3.3.1.2. Run-time Reset Sequence—RX 3.3.3.1.3. Run-time Reset Sequence—TX + RX
3.4. Simulation x
3.4.1. Test Case—Design Example with the IEEE 1588v2 Feature 3.4.2. Test Case—Design Example without the IEEE 1588v2 Feature
3.5. Hardware Testing x
3.5.1. Test Procedure 3.5.2. Design Constraints
4. Interface Signals Description x
4.1. Clock and Reset Interface Signals 4.2. Avalon® Memory-Mapped Interface Signals 4.3. Avalon® Streaming Interface Signals 4.4. PHY Interface Signals 4.5. Status Interface 4.6. IEEE 1588v2 Timestamp Interface Signals 4.7. Packet Classifier Interface Signals 4.8. TOD Interface Signals
5. Configuration Registers Description x
5.1. Register Access Definition 5.2. Low Latency Ethernet 10G MAC 5.3. PHY 5.4. TOD
5.3. PHY x
5.3.1. 1G/2.5G/5G/10G Multirate PHY
1. About the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide
2. Quick Start Guide
3. 10M/100M/1G/2.5G/5G/10G (USXGMII) Ethernet Design Example
4. Interface Signals Description
5. Configuration Registers Description
6. F-Tile Low Latency Ethernet 10G MAC Intel FPGA IP Design Example User Guide Archives
7. Document Revision History for the F-Tile Low Latency Ethernet 10G MAC Intel® FPGA IP Design Example User Guide

3.5.1. Test Procedure

After running the command: source main.tcl, a list of available JTAG Masters is displayed. By default, the first JTAG master is selected. To select the JTAG master for Agilex™ 7 devices, run this command: set_jtag <JTAG Master>. Example: set_jtag 1.

Follow these steps to test the design examples in hardware:

  1. Run the following command in the system console to start the test.

    TEST_EXT_LB <channel> <speed> <burst_size>

    Example: TEST_EXT_LB 0 10G 80000000

    Table 8.  Command Parameters
    Parameter Valid Values Description
    channel 0, 1 The channel number to test.
    speed 10M, 100M, 1G, 2P5G, 5G, 10G The PHY speed.
    burst_size An integer value The number of packets to generate for the test.
  2. When the test is completed, observe the output displayed. The following diagrams show excerpts of the output, which shows that the Ethernet packet monitor block receives the same number of packets generated without error, and the TX and RX statistics counters.
Figure 16. Sample Test Output—Ethernet Packet Monitor
Figure 17. Sample Test Output—Statistics Counters
Level Two Title