Cyclone® 10 GX FPGA Development Kit User Guide

Download PDF
ID 683696
Date 8/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Document Revision History for the Cyclone® 10 GX FPGA Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Development Kit Package
3. Development Kit Setup x
3.1. Setting up the Development Kit 3.2. Default Switch and Jumper Settings
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Using the Board Test System
4.3. Using the Board Test System x
4.3.1. The Configure Menu 4.3.2. The System Info Tab 4.3.3. The GPIO Tab 4.3.4. The EPCQ Tab Read Write Random Increase Erase Flash Memory Map 4.3.5. The XCVR Tab 4.3.6. The FMC Tab 4.3.7. The DDR3 Tab 4.3.8. Power Monitor 4.3.9. Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Cyclone® 10 GX FPGA A.3. MAX 10 System Controller A.4. FPGA Configuration A.5. Status and User I/O Elements A.6. Clocks A.7. Memory A.8. Power A.9. Transceivers Interfaces and Communication Ports
A.5. Status and User I/O Elements x
A.5.1. Switches A.5.2. Pushbuttons A.5.3. LEDs
A.7. Memory x
A.7.1. EMIF with DDR3 A.7.2. QSPI Flash
A.9. Transceivers Interfaces and Communication Ports x
A.9.1. Transceiver Channels A.9.2. PCIe Interface A.9.3. SFP+ Interface A.9.4. USB3.1 Type-C Interface A.9.5. FPGA Mezzanine Card (FMC) Interface A.9.6. 10/100/1000Base-T Ethernet Connector A.9.7. I2C/PMBUS
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance and Conformity Statements
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Document Revision History for the Cyclone® 10 GX FPGA Development Kit User Guide
A. Development Kit Components
B. Additional Information

4.3.4. The EPCQ Tab

The EPCQ tab allows you to read and write EPCQ flash memory on your board. The memory table displays the address 0 contents by default after you configure the FPGA.

Note: The EPCQ tab works only when the board MSEL is configured on AS mode.
Figure 9. The EPCQ (Flash) Tab

The following sections describe the controls on the Flash tab

Read

Reads the flash memory on your board. To see the flash memory contents, type a starting address in the text box and click Read. Values starting at the specified address in the table.

Write

Writes the flash memory on your board. To update the flash memory contents, change values in the table then press the Enter key and click Write. The application writes the new values to flash memory and then reads the values back to guarantee that the graphical display accurately reflects the memory contents.

Random

Starts a random data pattern test to flash memory, limited to the 512K test system scratch page.

Increase

Starts an incrementing data pattern test to flash memory, limited to the 512K test system scratch page.

Erase

Erases flash memory of the current sector.

Flash Memory Map

Displays the flash memory map for the development board.

Level Two Title