Cyclone® 10 GX FPGA Development Kit User Guide

Download PDF
ID 683696
Date 8/09/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Document Revision History for the Cyclone® 10 GX FPGA Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Development Kit Package
3. Development Kit Setup x
3.1. Setting up the Development Kit 3.2. Default Switch and Jumper Settings
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Using the Board Test System
4.3. Using the Board Test System x
4.3.1. The Configure Menu 4.3.2. The System Info Tab 4.3.3. The GPIO Tab 4.3.4. The EPCQ Tab 4.3.5. The XCVR Tab 4.3.6. The FMC Tab 4.3.7. The DDR3 Tab 4.3.8. Power Monitor 4.3.9. Clock Controller
A. Development Kit Components x
A.1. Board Overview A.2. Cyclone® 10 GX FPGA A.3. MAX 10 System Controller A.4. FPGA Configuration A.5. Status and User I/O Elements A.6. Clocks A.7. Memory A.8. Power A.9. Transceivers Interfaces and Communication Ports
A.5. Status and User I/O Elements x
A.5.1. Switches A.5.2. Pushbuttons A.5.3. LEDs
A.7. Memory x
A.7.1. EMIF with DDR3 A.7.2. QSPI Flash
A.9. Transceivers Interfaces and Communication Ports x
A.9.1. Transceiver Channels A.9.2. PCIe Interface A.9.3. SFP+ Interface A.9.4. USB3.1 Type-C Interface A.9.5. FPGA Mezzanine Card (FMC) Interface A.9.6. 10/100/1000Base-T Ethernet Connector A.9.7. I2C/PMBUS
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance and Conformity Statements
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Document Revision History for the Cyclone® 10 GX FPGA Development Kit User Guide
A. Development Kit Components
B. Additional Information

3.1. Setting up the Development Kit

To prepare and apply power to the board, perform the following steps:

The Cyclone® 10 GX FPGA Development Kit has two modes of operation:
  • Standard PCIe* -compliant system:

    In this mode, plug the board into an available PCIe* slot and connect the standard 2x4 PCIe* auxiliary power available from the PC's ATX power supply to the mating connector on the board (J12), and remove any power supply connected to J13. The PCIe* slot together with the PCIe* power is required to power the entire board with power up to 75 Watt. If ATX power is not connected, ensure that your PCIe* system can provide up to 75 Watt of power through the PCIe* slot alone. The power switch S14 is ignored when the board is used in the PCIe* .

  • Stand-alone evaluation board:

    In this mode, plug the included power supply into the power adapter connector (J13) and the AC power cord of the power supply into a power outlet. Remove any ATX power supply that is connected from the 2x4 power connector (J12). The power switch S14 powers ON/OFF the board.

Level Two Title