Visible to Intel only — GUID: jky1505489283654
Ixiasoft
1. Introduction
2. Quick Start Guide
3. Interface Overview
4. Parameters
5. Designing with the IP Core
6. Block Descriptions
7. Registers
8. Programming Model for the DMA Descriptor Controller
9. Programming Model for the Avalon® -MM Root Port
10. Avalon-MM Testbench and Design Example
11. Document Revision History
A. PCI Express Core Architecture
B. Root Port Enumeration
C. Troubleshooting and Observing the Link Status
2.1. Design Components
2.2. Hardware and Software Requirements
2.3. Directory Structure
2.4. Generating the Design Example
2.5. Simulating the Design Example
2.6. Compiling the Design Example and Programming the Device
2.7. Installing the Linux Kernel Driver
2.8. Running the Design Example Application
7.1.1. Register Access Definitions
7.1.2. PCI Configuration Header Registers
7.1.3. PCI Express Capability Structures
7.1.4. Intel Defined VSEC Capability Header
7.1.5. Uncorrectable Internal Error Status Register
7.1.6. Uncorrectable Internal Error Mask Register
7.1.7. Correctable Internal Error Status Register
7.1.8. Correctable Internal Error Mask Register
7.2.1.1. Avalon-MM to PCI Express Interrupt Status Registers
7.2.1.2. Avalon-MM to PCI Express Interrupt Enable Registers
7.2.1.3. Address Mapping for High-Performance Avalon-MM 32-Bit Slave Modules
7.2.1.4. PCI Express to Avalon-MM Interrupt Status and Enable Registers for Endpoints
7.2.1.5. PCI Express Configuration Information Registers
10.5.1. ebfm_barwr Procedure
10.5.2. ebfm_barwr_imm Procedure
10.5.3. ebfm_barrd_wait Procedure
10.5.4. ebfm_barrd_nowt Procedure
10.5.5. ebfm_cfgwr_imm_wait Procedure
10.5.6. ebfm_cfgwr_imm_nowt Procedure
10.5.7. ebfm_cfgrd_wait Procedure
10.5.8. ebfm_cfgrd_nowt Procedure
10.5.9. BFM Configuration Procedures
10.5.10. BFM Shared Memory Access Procedures
10.5.11. BFM Log and Message Procedures
10.5.12. Verilog HDL Formatting Functions
Visible to Intel only — GUID: jky1505489283654
Ixiasoft
10.3. Avalon® -MM Test Driver Module
The BFM driver module, altpcie_bfm_rp_gen3_x8.sv tests the DMA example Endpoint design. The BFM driver module configures the Endpoint Configuration Space registers and then tests the example Endpoint DMA channel. This file is in the <testbench_dir>pcie_<dev>_hip_avmm_bridge_0_example_design/pcie_example_design_tb/ip/pcie_example_design_tb/DUT_pcie_tb_ip/altera_pcie_<dev>_tbed_<ver>/sim directory.
The BFM test driver module performs the following steps in sequence:
- Configures the Root Port and Endpoint Configuration Spaces, which the BFM test driver module does by calling the procedure ebfm_cfg_rp_ep, which is part of altpcietb_bfm_rp_gen3_x8.sv.
- Finds a suitable BAR to access the example Endpoint design Control Register space.
- If find_mem_baridentifies a suitable BAR in the previous step, the driver performs the following tasks:
- DMA read: The driver programs the DMA to read data from the BFM shared memory into the Endpoint memory. The DMA issues an MSI when the last descriptor completes.
- DMA writ: The driver programs the DMA to write the data from its Endpoint memory back to the BFM shared memory. The DMA completes the following steps to indicate transfer completion:
- The DMA issues an MSI when the last descriptor completes.
- A checker compares the data written back to BFM against the data that read from the BFM.
- The driver programs the DMA to perform a test that demonstrates downstream access of the DMA Endpoint memory.