Arria® 10 FPGA Development Kit User Guide

Download PDF
ID 683526
Date 5/15/2024
Public
Document Table of Contents
Document Table of Contents x
1. Arria® 10 FPGA Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Update Portal 6. Board Components A. Additional Information
1. Arria® 10 FPGA Development Kit Overview x
1.1. General Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Subscription Edition Software 2.2. Development Kit Package 2.3. Installing the Intel® FPGA Download Cable Driver
2.1. Installing the Subscription Edition Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings 3.3. Default Switch and Resistor Settings 3.4. Factory Reset
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The Flash Tab 4.4.5. The XCVR Tab 4.4.6. The PCIe® Tab 4.4.7. The FMC A Tab 4.4.8. The FMC B Tab 4.4.9. The DDR3 Tab 4.4.10. The DDR4 Tab 4.4.11. The Power Monitor 4.4.12. The Clock Controller
5. Board Update Portal x
5.1. Connecting to the Board Update Portal Web Page
5.1. Connecting to the Board Update Portal Web Page x
5.1.1. Using the Board Update Portal to Update User Designs
6. Board Components x
6.1. Board Overview 6.2. MAX V CPLD System Controller 6.3. FPGA Configuration 6.4. Status Elements 6.5. User Input/Output 6.6. Clock Circuitry 6.7. Components and Interfaces 6.8. Memory 6.9. Board Power Supply 6.10. Daughtercards
6.3. FPGA Configuration x
6.3.1. Configuring the FPGA Using Programmer
6.5. User Input/Output x
6.5.1. User-Defined Push Buttons 6.5.2. User-Defined DIP Switch 6.5.3. User-Defined LEDs 6.5.4. Character LCD 6.5.5. DisplayPort 6.5.6. SDI Video Input/Output Ports
6.6. Clock Circuitry x
6.6.1. On-Board Oscillators 6.6.2. Off-Board Clock I/O
6.7. Components and Interfaces x
6.7.1. PCI Express 6.7.2. 10/100/1000 Ethernet PHY 6.7.3. HiLo External Memory Interface 6.7.4. FMC 6.7.5. QSFP 6.7.6. SFP+ 6.7.7. I2C
6.8. Memory x
6.8.1. Flash 6.8.2. Programming the Flash Using Quartus® Prime Programmer
6.9. Board Power Supply x
6.9.1. Power Distribution System 6.9.2. Power Measurement
6.10. Daughtercards x
6.10.1. External Memory Interface
6.10.1. External Memory Interface x
6.10.1.1. DDR3L 6.10.1.2. DDR4 6.10.1.3. RLDRAM 3 6.10.1.4. QDR-IV 6.10.1.5. FMC Loopback Card
6.10.1.5. FMC Loopback Card x
6.10.1.5.1. High Pin Count (HBC) 6.10.1.5.2. Low Pin Count (LPC)
A. Additional Information x
A.1. Document Revision History for the Arria® 10 FPGA Development Kit User Guide A.2. Compliance and Conformity Statements
A.2. Compliance and Conformity Statements x
A.2.1. CE EMI Conformity Caution
1. Arria® 10 FPGA Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Update Portal
6. Board Components
A. Additional Information

4.4.1. Using the Configure Menu

Use the Configure menu to select the design you want to use. Each design example tests different board features. Choose a design from this menu and the corresponding tabs become active for testing.
Figure 15. The Configure Menu

To configure the FPGA with a test system design, perform the following steps:

  1. On the Configure menu, click the configure command that corresponds to the functionality you wish to test.
  2. In the dialog box that appears, click Configure to download the corresponding design to the FPGA.
  3. When configuration finishes, close the Quartus® Prime Programmer if open. The design begins running in the FPGA. The corresponding GUI application tabs that interface with the design are now enabled.
If you use the Quartus® Prime Programmer for configuration, rather than the Board Test System GUI, you may need to restart the GUI.
Level Two Title