Arria® 10 FPGA Development Kit User Guide

Download PDF
ID 683526
Date 5/15/2024
Public

Visible to Intel only — GUID: sth1399416676991

Ixiasoft

View Details

Document Table of Contents
Document Table of Contents x
1. Arria® 10 FPGA Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Update Portal 6. Board Components A. Additional Information
1. Arria® 10 FPGA Development Kit Overview x
1.1. General Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Subscription Edition Software 2.2. Development Kit Package 2.3. Installing the Intel® FPGA Download Cable Driver
2.1. Installing the Subscription Edition Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings 3.3. Default Switch and Resistor Settings 3.4. Factory Reset
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The Flash Tab 4.4.5. The XCVR Tab 4.4.6. The PCIe® Tab 4.4.7. The FMC A Tab 4.4.8. The FMC B Tab 4.4.9. The DDR3 Tab 4.4.10. The DDR4 Tab 4.4.11. The Power Monitor 4.4.12. The Clock Controller
5. Board Update Portal x
5.1. Connecting to the Board Update Portal Web Page
5.1. Connecting to the Board Update Portal Web Page x
5.1.1. Using the Board Update Portal to Update User Designs
6. Board Components x
6.1. Board Overview 6.2. MAX V CPLD System Controller 6.3. FPGA Configuration 6.4. Status Elements 6.5. User Input/Output 6.6. Clock Circuitry 6.7. Components and Interfaces 6.8. Memory 6.9. Board Power Supply 6.10. Daughtercards
6.3. FPGA Configuration x
6.3.1. Configuring the FPGA Using Programmer
6.5. User Input/Output x
6.5.1. User-Defined Push Buttons 6.5.2. User-Defined DIP Switch 6.5.3. User-Defined LEDs 6.5.4. Character LCD 6.5.5. DisplayPort 6.5.6. SDI Video Input/Output Ports
6.6. Clock Circuitry x
6.6.1. On-Board Oscillators 6.6.2. Off-Board Clock I/O
6.7. Components and Interfaces x
6.7.1. PCI Express 6.7.2. 10/100/1000 Ethernet PHY 6.7.3. HiLo External Memory Interface 6.7.4. FMC 6.7.5. QSFP 6.7.6. SFP+ 6.7.7. I2C
6.8. Memory x
6.8.1. Flash 6.8.2. Programming the Flash Using Quartus® Prime Programmer
6.9. Board Power Supply x
6.9.1. Power Distribution System 6.9.2. Power Measurement
6.10. Daughtercards x
6.10.1. External Memory Interface
6.10.1. External Memory Interface x
6.10.1.1. DDR3L 6.10.1.2. DDR4 6.10.1.3. RLDRAM 3 6.10.1.4. QDR-IV 6.10.1.5. FMC Loopback Card
6.10.1.5. FMC Loopback Card x
6.10.1.5.1. High Pin Count (HBC) 6.10.1.5.2. Low Pin Count (LPC)
A. Additional Information x
A.1. Document Revision History for the Arria® 10 FPGA Development Kit User Guide A.2. Compliance and Conformity Statements
A.2. Compliance and Conformity Statements x
A.2.1. CE EMI Conformity Caution
1. Arria® 10 FPGA Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Update Portal
6. Board Components
A. Additional Information

4.2. Running the Board Test System

To run the Board Test System (BTS), navigate to the <package dir>\examples\board_test_system directory and double click BoardTestSystem.bat.

A GUI appears, displaying the application tab that corresponds to the design running in the FPGA. The development board’s flash memory ships preconfigured with the design that corresponds to the GPIO tab.

Note: The BTS relies on the Quartus® Prime software's specific library. Before running the BTS, open the Quartus® Prime software. It sets the environment variable $QUARTUS_ROOTDIR automatically. The Board Test System uses this environment variable to locate the Quartus® Prime library.

The BTS picks up the Quartus® Prime Programmer to configure the FPGA device on your development kit. Make sure the Quartus® Prime software you are using is the version supporting the FPGA silicon on the board.

Level Two Title