Arria® 10 FPGA Development Kit User Guide

Download PDF
ID 683526
Date 5/15/2024
Public
Document Table of Contents
Document Table of Contents x
1. Arria® 10 FPGA Development Kit Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Board Update Portal 6. Board Components A. Additional Information
1. Arria® 10 FPGA Development Kit Overview x
1.1. General Description 1.2. Recommended Operating Conditions 1.3. Handling the Board
2. Getting Started x
2.1. Installing the Subscription Edition Software 2.2. Development Kit Package 2.3. Installing the Intel® FPGA Download Cable Driver
2.1. Installing the Subscription Edition Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Board 3.2. Default Switch and Jumper Settings 3.3. Default Switch and Resistor Settings 3.4. Factory Reset
4. Board Test System x
4.1. Preparing the Board 4.2. Running the Board Test System 4.3. Version Selector 4.4. Using the Board Test System
4.4. Using the Board Test System x
4.4.1. Using the Configure Menu 4.4.2. The System Info Tab 4.4.3. The GPIO Tab 4.4.4. The Flash Tab 4.4.5. The XCVR Tab 4.4.6. The PCIe® Tab 4.4.7. The FMC A Tab 4.4.8. The FMC B Tab 4.4.9. The DDR3 Tab 4.4.10. The DDR4 Tab 4.4.11. The Power Monitor 4.4.12. The Clock Controller
5. Board Update Portal x
5.1. Connecting to the Board Update Portal Web Page
5.1. Connecting to the Board Update Portal Web Page x
5.1.1. Using the Board Update Portal to Update User Designs
6. Board Components x
6.1. Board Overview 6.2. MAX V CPLD System Controller 6.3. FPGA Configuration 6.4. Status Elements 6.5. User Input/Output 6.6. Clock Circuitry 6.7. Components and Interfaces 6.8. Memory 6.9. Board Power Supply 6.10. Daughtercards
6.3. FPGA Configuration x
6.3.1. Configuring the FPGA Using Programmer
6.5. User Input/Output x
6.5.1. User-Defined Push Buttons 6.5.2. User-Defined DIP Switch 6.5.3. User-Defined LEDs 6.5.4. Character LCD 6.5.5. DisplayPort 6.5.6. SDI Video Input/Output Ports
6.6. Clock Circuitry x
6.6.1. On-Board Oscillators 6.6.2. Off-Board Clock I/O
6.7. Components and Interfaces x
6.7.1. PCI Express 6.7.2. 10/100/1000 Ethernet PHY 6.7.3. HiLo External Memory Interface 6.7.4. FMC 6.7.5. QSFP 6.7.6. SFP+ 6.7.7. I2C
6.8. Memory x
6.8.1. Flash 6.8.2. Programming the Flash Using Quartus® Prime Programmer
6.9. Board Power Supply x
6.9.1. Power Distribution System 6.9.2. Power Measurement
6.10. Daughtercards x
6.10.1. External Memory Interface
6.10.1. External Memory Interface x
6.10.1.1. DDR3L 6.10.1.2. DDR4 6.10.1.3. RLDRAM 3 6.10.1.4. QDR-IV 6.10.1.5. FMC Loopback Card
6.10.1.5. FMC Loopback Card x
6.10.1.5.1. High Pin Count (HBC) 6.10.1.5.2. Low Pin Count (LPC)
A. Additional Information x
A.1. Document Revision History for the Arria® 10 FPGA Development Kit User Guide A.2. Compliance and Conformity Statements
A.2. Compliance and Conformity Statements x
A.2.1. CE EMI Conformity Caution
1. Arria® 10 FPGA Development Kit Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Board Update Portal
6. Board Components
A. Additional Information

4.1. Preparing the Board

With the power to the board off, follow these steps:
  1. Connect the USB cable to your PC and the board.
  2. Ensure that the Ethernet patch cord is plugged into the RJ-45 connector.
  3. Check the development board switches and jumpers are set according to your preferences. See the Factory Default Switch and Jumper Settings section.
  4. Set the load selector switch (SW6.4) to OFF for user hardware1 (page #1).
    The development board ships with the CFI flash device preprogrammed with a default:
    • Factory FPGA configuration for running the Board Update Portal design example
    • User configuration for running the Board Test System demonstration
  5. Turn on the power to the board. The board loads the design stored in the user hardware1 portion of flash memory into the FPGA. If your board is still in the factory configuration, or if you have downloaded a newer version of the Board Test System to flash memory through the Board Update Portal, the design loads the GPIO, Ethernet, and flash memory tests.
    To ensure operating stability, keep the USB cable connected and the board powered on when running the demonstration application. The application cannot run correctly unless the USB cable is attached and the board is on.
Related Information
Level Two Title