AN 1003: Multi Memory IP System Resource Planning: for Intel Agilex® 7 M-Series FPGAs

Download PDF
ID 788295
Date 11/22/2023
Public
Document Table of Contents
Document Table of Contents x
1. Answers to Top FAQs 2. About This Application Note 3. Component Bandwidth Projections and Limitations 4. Resource Planning for Intel Agilex® 7 M-Series FPGAs 5. Factors Affecting NoC Performance 6. Debugging the NoC 7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs
2. About This Application Note x
2.1. Preliminary Guidelines 2.2. Document Prerequisites 2.3. Terminology for Intel Agilex® 7 M-Series FPGAs
3. Component Bandwidth Projections and Limitations x
3.1. Memory Controller Efficiency 3.2. Hard Memory NoC Bandwidth 3.3. Overall Bandwidth for NoC Systems
3.1. Memory Controller Efficiency x
3.1.1. HBM2E UIB Controller Efficiency 3.1.2. External Memory Interface Controller Efficiency
3.2. Hard Memory NoC Bandwidth x
3.2.1. Horizontal NoC Bandwidth 3.2.2. Initiator NoC Bandwidth 3.2.3. Target NoC Bandwidth 3.2.4. Initiator Target Link Bandwidth
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs x
4.1. Hard Memory NoC Resource Planning Overview 4.2. I/O Bank Blockage 4.3. Planning Avalon® Streaming Utilization 4.4. Planning for Initiator Blockage Impact from GPIO, LVDS SERDES, and PHY Lite Bypass Mode 4.5. Planning NoC PLL and I/O PLL 4.6. Pin Planning for HPS EMIF 4.7. Planning for an External Memory Interface 4.8. Planning for HBM2E 4.9. Planning for the Fabric NoC 4.10. Planning for AXI4-Lite 4.11. Planning NoC and Memory Solution Clocks
4.2. I/O Bank Blockage x
4.2.1. Top Hard Memory NoC 4.2.2. Bottom Hard Memory NoC
4.10. Planning for AXI4-Lite x
4.10.1. Single AXI4 Lite Initiator for Each Horizontal NoC 4.10.2. AXI4-Lite Initiator for HBM2E 4.10.3. AXI4-Lite Initiator for EMIF
4.11. Planning NoC and Memory Solution Clocks x
4.11.1. Clocking without the Fabric NoC 4.11.2. Clocking with the Fabric NoC
5. Factors Affecting NoC Performance x
5.1. Recommended Performance Tuning Procedure 5.2. NoC Initiator and Target Clock Rate 5.3. Recommended NoC Design Topologies 5.4. Traffic Access Pattern and Memory Controller Efficiency 5.5. Traffic Access Pattern Due To Multiple Traffic Flows 5.6. Transaction Size 5.7. Congestion Interaction 5.8. Bandwidth Sharing At Each Switch 5.9. Exceeding NoC Bandwidth Limits 5.10. Maximum Number of Outstanding Transactions 5.11. QoS Priority 5.12. AxID 5.13. Example: 2x2 HBM Crossbars 5.14. Example: 16x16 Crossbar
5.3. Recommended NoC Design Topologies x
5.3.1. 1:1 Connectivity with EMIF and HBM 5.3.2. HBM Crossbars 5.3.3. Connectivity with HPS
6. Debugging the NoC x
6.1. Debugging NoC AXI Transaction Issues 6.2. Debugging NoC Bit Errors 6.3. Debugging NoC Performance Issues
6.3. Debugging NoC Performance Issues x
6.3.1. Measuring Performance with the Signal Tap Logic Analyzer 6.3.2. Measuring Performance with the Performance Monitor 6.3.3. Performance Debug Steps
1. Answers to Top FAQs
2. About This Application Note
3. Component Bandwidth Projections and Limitations
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs
5. Factors Affecting NoC Performance
6. Debugging the NoC
7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs

5.2. NoC Initiator and Target Clock Rate

Before proceeding to further optimization steps, maximize the NoC throughput by ensuring that your initiators and targets are running at the highest possible clock rate.

To first order, the throughput of a NoC initiator or target is limited to the interface width, multiplied by the interface clock rate. The connection throughput is limited by the minimum of the initiator or target throughput. For guidance on clocking options for the NoC Initiator Intel FPGA IP to maximize throughput, refer to Planning NoC and Memory Solution Clocks.

A reduced clock rate may be appropriate under any of the following conditions:

  • The user logic that you connect to cannot close timing at high clock rates.
  • You intend to reduce the clock rate to reduce dynamic power.
  • You expect access patterns with reduced memory controller efficiency, and you expect a lower rate of issuing transactions.

For guidance on memory controller clock rates and supported fastest configurations, refer to the following related information.

Related Information
Level Two Title