AN 1003: Multi Memory IP System Resource Planning: for Intel Agilex® 7 M-Series FPGAs

Download PDF
ID 788295
Date 11/22/2023
Public
Document Table of Contents
Document Table of Contents x
1. Answers to Top FAQs 2. About This Application Note 3. Component Bandwidth Projections and Limitations 4. Resource Planning for Intel Agilex® 7 M-Series FPGAs 5. Factors Affecting NoC Performance 6. Debugging the NoC 7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs
2. About This Application Note x
2.1. Preliminary Guidelines 2.2. Document Prerequisites 2.3. Terminology for Intel Agilex® 7 M-Series FPGAs
3. Component Bandwidth Projections and Limitations x
3.1. Memory Controller Efficiency 3.2. Hard Memory NoC Bandwidth 3.3. Overall Bandwidth for NoC Systems
3.1. Memory Controller Efficiency x
3.1.1. HBM2E UIB Controller Efficiency 3.1.2. External Memory Interface Controller Efficiency
3.2. Hard Memory NoC Bandwidth x
3.2.1. Horizontal NoC Bandwidth 3.2.2. Initiator NoC Bandwidth 3.2.3. Target NoC Bandwidth 3.2.4. Initiator Target Link Bandwidth
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs x
4.1. Hard Memory NoC Resource Planning Overview 4.2. I/O Bank Blockage 4.3. Planning Avalon® Streaming Utilization 4.4. Planning for Initiator Blockage Impact from GPIO, LVDS SERDES, and PHY Lite Bypass Mode 4.5. Planning NoC PLL and I/O PLL 4.6. Pin Planning for HPS EMIF 4.7. Planning for an External Memory Interface 4.8. Planning for HBM2E 4.9. Planning for the Fabric NoC 4.10. Planning for AXI4-Lite 4.11. Planning NoC and Memory Solution Clocks
4.2. I/O Bank Blockage x
4.2.1. Top Hard Memory NoC 4.2.2. Bottom Hard Memory NoC
4.10. Planning for AXI4-Lite x
4.10.1. Single AXI4 Lite Initiator for Each Horizontal NoC 4.10.2. AXI4-Lite Initiator for HBM2E 4.10.3. AXI4-Lite Initiator for EMIF
4.11. Planning NoC and Memory Solution Clocks x
4.11.1. Clocking without the Fabric NoC 4.11.2. Clocking with the Fabric NoC
5. Factors Affecting NoC Performance x
5.1. Recommended Performance Tuning Procedure 5.2. NoC Initiator and Target Clock Rate 5.3. Recommended NoC Design Topologies 5.4. Traffic Access Pattern and Memory Controller Efficiency 5.5. Traffic Access Pattern Due To Multiple Traffic Flows 5.6. Transaction Size 5.7. Congestion Interaction 5.8. Bandwidth Sharing At Each Switch 5.9. Exceeding NoC Bandwidth Limits 5.10. Maximum Number of Outstanding Transactions 5.11. QoS Priority 5.12. AxID 5.13. Example: 2x2 HBM Crossbars 5.14. Example: 16x16 Crossbar
5.3. Recommended NoC Design Topologies x
5.3.1. 1:1 Connectivity with EMIF and HBM 5.3.2. HBM Crossbars 5.3.3. Connectivity with HPS
6. Debugging the NoC x
6.1. Debugging NoC AXI Transaction Issues 6.2. Debugging NoC Bit Errors 6.3. Debugging NoC Performance Issues
6.3. Debugging NoC Performance Issues x
6.3.1. Measuring Performance with the Signal Tap Logic Analyzer 6.3.2. Measuring Performance with the Performance Monitor 6.3.3. Performance Debug Steps
1. Answers to Top FAQs
2. About This Application Note
3. Component Bandwidth Projections and Limitations
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs
5. Factors Affecting NoC Performance
6. Debugging the NoC
7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs

5.3.3. Connectivity with HPS

In scenarios that combine the HPS and HBM, it is best to move the HBM access as far left as possible. This technique reduces the overlapping traffic on the NoC with the HPS traffic to its two adjacent EMIFs.

In the diagram below, there are no initiators that access the EMIF on the right side, so the HBM connections can be moved to the left.

Figure 23. Initiators Can Be Moved Left


With just a straight mapping of initiators and targets, there is still some overlap with the left HPS memory interface. The highlighted elements in HPS Connections Still Overlap indicate where HPS connections still overlap with HBM connections, potentially impacting the performance of the core-to-HBM or HPS-to-EMIF connection. Link 0 connections appear in red, Link 1 connections appear in green.

Figure 24. HPS Connections Still Overlap


By taking advantage of the distribution of targets on Link 0 and Link 1, it is possible to swap the location of the initiator highlighted in light blue, to avoid overlap with the HPS traffic.

Figure 25. Swap Initiator Location To Avoid Overlap with HPS Traffic


This placement also applies to LPDDR5 configurations using all four targets in I/O bank 3C and 3D.

Figure 26. LPDDR5 Configurations Using all Four Targets


Level Two Title