Visible to Intel only — GUID: sam1403482509326
Ixiasoft
1. Agilex™ 7 M-Series LVDS SERDES Overview
2. Agilex™ 7 M-Series LVDS SERDES Architecture
3. Agilex™ 7 M-Series LVDS SERDES Transmitter
4. Agilex™ 7 M-Series LVDS SERDES Receiver
5. Agilex™ 7 M-Series High-Speed LVDS I/O Implementation Guide
6. Agilex™ 7 M-Series LVDS SERDES Timing
7. LVDS SERDES Intel® FPGA IP Design Examples
8. Agilex™ 7 M-Series LVDS SERDES Design Guidelines
9. Agilex™ 7 M-Series LVDS SERDES Troubleshooting Guidelines
10. Documentation Related to the Agilex™ 7 LVDS SERDES User Guide: M-Series
11. Document Revision History for the Agilex™ 7 LVDS SERDES User Guide: M-Series
5.1.6.1. LVDS SERDES Intel® FPGA IP General Settings
5.1.6.2. LVDS SERDES Intel® FPGA IP Pin Settings
5.1.6.3. LVDS SERDES Intel® FPGA IP PLL Settings
5.1.6.4. LVDS SERDES Intel® FPGA IP Receiver Settings
5.1.6.5. LVDS SERDES Intel® FPGA IP Transmitter Settings
5.1.6.6. LVDS SERDES Intel® FPGA IP Clock Resource Summary
8.1. Use PLLs in Integer PLL Mode for LVDS SERDES
8.2. Use High-Speed Clock from PLL to Clock SERDES Only
8.3. Pin Placement for Differential Channels
8.4. SERDES Pin Pairs for Soft-CDR Mode
8.5. Placing LVDS SERDES Transmitters and Receivers in the Same GPIO-B Sub-Bank with External PLL
8.6. Sharing LVDS SERDES I/O Lane with Other Intel® FPGA IPs
8.7. VCCIO_PIO Power Scheme for LVDS SERDES
Visible to Intel only — GUID: sam1403482509326
Ixiasoft
5.2. LVDS Interface with External PLL Mode
The LVDS SERDES IP parameter editor provides an option to implement the LVDS interface with the Use External PLL option. With this option turned on you can control the PLL settings, such as dynamically reconfiguring the PLL to support different data rates, dynamic phase shift, and other settings.
If you enable the Use External PLL option with the LVDS SERDES IP core transmitter and receiver, the following signals are required from the IOPLL Intel® FPGA IP:
- Serial clock (fast clock) input to the SERDES of the LVDS SERDES IP transmitter and receiver
- Parallel clock (core clock) used to clock the transmitter FPGA fabric logic and parallel clock used for the receiver
- Asynchronous PLL reset port of the LVDS SERDES IP receiver
- PLL VCO signal for the transmitter and DPA receiver modes of the LVDS SERDES IP
The Clock Resource Summary tab in the LVDS SERDES IP parameter editor provides the details for the signals in the preceding list.
You must instantiate an IOPLL IP to generate the various clocks and load enable signals. Configure these settings in the IOPLL IP parameter editor:
- In the Settings tab, specify the LVDS External PLL settings.
- In the PLL tab:
- Set the Output Clocks settings.
- Select the Compensation Mode according to the following table.
LVDS Functional Mode | IOPLL IP Compensation Mode |
---|---|
TX (without RX non-DPA), RX DPA, RX Soft-CDR | direct |
RX non-DPA (with or without TX) | lvds |