Symmetric Cryptographic Intel FPGA Hard IP User Guide

Download PDF
ID 714305
Date 10/02/2023
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. Interface Overview 3. Parameters 4. Designing with the IP Core 5. Block Description 6. Cryptographic IP Data Profiles 7. Configuration Registers 8. Design Example 9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives 10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide
1. Introduction x
1.1. Terminology 1.2. IP Core Overview 1.3. Release Information 1.4. Device Family Support 1.5. Resource Utilization
1.2. IP Core Overview x
1.2.1. IP Core Applications
2. Interface Overview x
2.1. Clock Signals 2.2. Reset Signals 2.3. AXI-ST Interface 2.4. AXI-Lite Interface
4. Designing with the IP Core x
4.1. Installing and Licensing Intel® FPGA IP Cores 4.2. Specifying the IP Core Parameters and Options 4.3. Generated File Structure 4.4. Symmetric Cryptographic IP Core Flow 4.5. Dynamically Disabling SM4 Capability 4.6. Error Handling 4.7. Error Reporting 4.8. Resetting the IP Core 4.9. Channel Definition and Allocation 4.10. Byte Ordering 4.11. AXI-ST Single Packet Mode 4.12. AXI-ST Multiple Packet Mode
4.1. Installing and Licensing Intel® FPGA IP Cores x
4.1.1. Intel® FPGA IP Evaluation Mode
4.6. Error Handling x
4.6.1. Detected Error Handling 4.6.2. Key RAM ECC Error Handling
5. Block Description x
5.1. Reset Sequencer 5.2. AXI-ST Ready Latency 5.3. AXI Adapter 5.4. Integrity Check Value Comparison 5.5. GCM Padding and Depadding
5.3. AXI Adapter x
5.3.1. MAC Packing 5.3.2. Data Last Indicator 5.3.3. Stream and Channel ID Buffering 5.3.4. TKEEP and LAST_SEGMENT Signals Generation 5.3.5. MAC Dropping on Decryption
5.5. GCM Padding and Depadding x
5.5.1. GCM Padding 5.5.2. GCM Depadding
6. Cryptographic IP Data Profiles x
6.1. MAC Security Profile (MACsec) 6.2. IP Security Profile (IPsec) 6.3. Generic GCM Profile (GCM) 6.4. Generic XTS Profile (XTS)
6.1. MAC Security Profile (MACsec) x
6.1.1. MACsec Flow 6.1.2. AXI-ST Interface Using MAC Security (MACsec) Profile Pattern
6.2. IP Security Profile (IPsec) x
6.2.1. AXI-ST Interface Using IP Security (IPsec) Profile Pattern
6.3. Generic GCM Profile (GCM) x
6.3.1. AXI- ST Interface Using Generic GCM Profile Pattern
6.4. Generic XTS Profile (XTS) x
6.4.1. AXI-ST Interface Using Generic XTS Profile Pattern
8. Design Example x
8.1. Functional Description 8.2. Crypto VSIP Top Block Descriptions 8.3. Test Configurations 8.4. Software Requirements 8.5. Simulation Requirements 8.6. Steps to Generate the Design Example 8.7. Running Simulation Tests 8.8. Running Hardware Tests
8.2. Crypto VSIP Top Block Descriptions x
8.2.1. Clock and Reset 8.2.2. Host Interface
8.7. Running Simulation Tests x
8.7.1. Steps to Simulate the Design Example
8.8. Running Hardware Tests x
8.8.1. Supported Boards 8.8.2. Steps to Compile the Design Example for Hardware 8.8.3. Steps to Run the Design Example on Hardware
1. Introduction
2. Interface Overview
3. Parameters
4. Designing with the IP Core
5. Block Description
6. Cryptographic IP Data Profiles
7. Configuration Registers
8. Design Example
9. Symmetric Cryptographic Intel FPGA Hard IP User Guide Archives
10. Document Revision History for the Symmetric Cryptographic Intel FPGA Hard IP User Guide

8.7. Running Simulation Tests

Once you have generated the example design, next you need to execute the shell script to run the simulation. For example, to run a VCS simulation, just type sh run_vcs.sh at the command prompt in the testbench directory.

This generates the simulation setup script for the VCS simulator, compiles the design using the VCS design compiler, and then runs the simulator.

The output from the simulation consists of log outputs tracing through the operations. At the end of the simulation, you see an indication that the test has passed.

For a VCS simulation, a .vpd file is produced that can be examined with the waveform viewer to see the waveforms at the Symmetric Cryptographic Intel FPGA Hard IP.

The simulation scripts for the VCS* MX, QuestaSim* , and Xcelium* simulators run in the same fashion. These simulation scripts also produce waveform files that can be used to observe the simulation progress. The simulation testbenches for all four simulators work the same way.


Section Content
Steps to Simulate the Design Example

Level Two Title