Intel® Cyclone® 10 LP FPGA Evaluation Kit User Guide

Download PDF
ID 683580
Date 12/19/2019
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Evaluation Board Setup 4. Evaluation Board Components 5. Simple Socket Server 6. Board Test System A. Safety and Regulatory Information B. Additional Information
1. Overview x
1.1. Evaluation Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Board 1.4. Evaluation Board Revisions
1.1. Evaluation Kit Description x
1.1.1. Evaluation Board Description 1.1.2. Evaluation Kit Collateral 1.1.3. Power Supply Description
2. Getting Started x
2.1. Installing Quartus Prime Software 2.2. Installing the Evaluation Kit Collateral 2.3. Installing Intel® FPGA Download Cable Driver
3. Evaluation Board Setup x
3.1. Powering Up the Evaluation Board 3.2. Default Switch Settings 3.3. Recovering Factory Default Settings
4. Evaluation Board Components x
4.1. Board Overview 4.2. Intel® Cyclone® 10 LP FPGA Overview 4.3. MAX 10 System Controller Overview 4.4. FPGA Configuration 4.5. Status Elements 4.6. Setup Elements 4.7. General User Input/Output 4.8. Clocks 4.9. Connectors and Interfaces 4.10. Memory 4.11. System Power
4.4. FPGA Configuration x
4.4.1. Using the Quartus Prime Programmer 4.4.2. Program On-Board EPCQ or EPCQ-A Flash Memory 4.4.3. Active Serial Configuration
4.9. Connectors and Interfaces x
4.9.1. Gigabit Ethernet PHY 4.9.2. 2x20 GPIO Expansion Header 4.9.3. Arduino Connectors 4.9.4. Pmod Connectors
4.9.3. Arduino Connectors x
4.9.3.1. Digital IOs 4.9.3.2. Analog Inputs 4.9.3.3. Arduino Power
4.10. Memory x
4.10.1. HyperRAM 4.10.2. EPCQ or EPCQ-A Flash Memory
4.11. System Power x
4.11.1. Power Supply Options 4.11.2. Power Tree 4.11.3. Current Measurement
5. Simple Socket Server x
5.1. Connecting to the Simple Socket Server
6. Board Test System x
6.1. The Configure Menu 6.2. The System Info Tab 6.3. The GPIO Tab 6.4. The Flash Tab 6.5. The HyperRAM Tab 6.6. The Power Monitor 6.7. The Clock Control
A. Safety and Regulatory Information x
ENGINEERING DEVELOPMENT PRODUCT - NOT FOR RESALE OR LEASE A.1. Safety Warnings A.2. Safety Cautions
B. Additional Information x
B.1. Revision History B.2. Compliance and Conformity Statements
1. Overview
2. Getting Started
3. Evaluation Board Setup
4. Evaluation Board Components
5. Simple Socket Server
6. Board Test System
A. Safety and Regulatory Information
B. Additional Information

A. Safety and Regulatory Information

ENGINEERING DEVELOPMENT PRODUCT - NOT FOR RESALE OR LEASE

This development kit is intended for laboratory development and engineering use only.

This development kit is designed to allow:
  • Product developers and system engineers to evaluate electronic components, circuits, or software associated with the development kit to determine whether to incorporate such items in a finished product.
  • Software developers to write software applications for use with the end product.

This kit is not a finished product and when assembled may not be resold or otherwise marketed unless all required Federal Communications Commission (FCC) equipment authorizations are first obtained.

Operation is subject to the condition that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.

Unless the assembled kit is designed to operate under Part 15, Part 18 or Part 95 of the United States Code of Federal Regulations (CFR) Title 47, the operator of the kit must operate under the authority of an FCC license holder or must secure an experimental authorization under Part 5 of the United States CFR Title 47.

Safety Assessment and CE mark requirements have been completed, however, other certifications that may be required for installation and operation in your region have not been obtained.


Section Content
Safety Warnings
Safety Cautions

Level Two Title