AN 1003: Multi Memory IP System Resource Planning: for Intel Agilex® 7 M-Series FPGAs

Download PDF
ID 788295
Date 11/22/2023
Public
Document Table of Contents
Document Table of Contents x
1. Answers to Top FAQs 2. About This Application Note 3. Component Bandwidth Projections and Limitations 4. Resource Planning for Intel Agilex® 7 M-Series FPGAs 5. Factors Affecting NoC Performance 6. Debugging the NoC 7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs
2. About This Application Note x
2.1. Preliminary Guidelines 2.2. Document Prerequisites 2.3. Terminology for Intel Agilex® 7 M-Series FPGAs
3. Component Bandwidth Projections and Limitations x
3.1. Memory Controller Efficiency 3.2. Hard Memory NoC Bandwidth 3.3. Overall Bandwidth for NoC Systems
3.1. Memory Controller Efficiency x
3.1.1. HBM2E UIB Controller Efficiency 3.1.2. External Memory Interface Controller Efficiency
3.2. Hard Memory NoC Bandwidth x
3.2.1. Horizontal NoC Bandwidth 3.2.2. Initiator NoC Bandwidth 3.2.3. Target NoC Bandwidth 3.2.4. Initiator Target Link Bandwidth
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs x
4.1. Hard Memory NoC Resource Planning Overview 4.2. I/O Bank Blockage 4.3. Planning Avalon® Streaming Utilization 4.4. Planning for Initiator Blockage Impact from GPIO, LVDS SERDES, and PHY Lite Bypass Mode 4.5. Planning NoC PLL and I/O PLL 4.6. Pin Planning for HPS EMIF 4.7. Planning for an External Memory Interface 4.8. Planning for HBM2E 4.9. Planning for the Fabric NoC 4.10. Planning for AXI4-Lite 4.11. Planning NoC and Memory Solution Clocks
4.2. I/O Bank Blockage x
4.2.1. Top Hard Memory NoC 4.2.2. Bottom Hard Memory NoC
4.10. Planning for AXI4-Lite x
4.10.1. Single AXI4 Lite Initiator for Each Horizontal NoC 4.10.2. AXI4-Lite Initiator for HBM2E 4.10.3. AXI4-Lite Initiator for EMIF
4.11. Planning NoC and Memory Solution Clocks x
4.11.1. Clocking without the Fabric NoC 4.11.2. Clocking with the Fabric NoC
5. Factors Affecting NoC Performance x
5.1. Recommended Performance Tuning Procedure 5.2. NoC Initiator and Target Clock Rate 5.3. Recommended NoC Design Topologies 5.4. Traffic Access Pattern and Memory Controller Efficiency 5.5. Traffic Access Pattern Due To Multiple Traffic Flows 5.6. Transaction Size 5.7. Congestion Interaction 5.8. Bandwidth Sharing At Each Switch 5.9. Exceeding NoC Bandwidth Limits 5.10. Maximum Number of Outstanding Transactions 5.11. QoS Priority 5.12. AxID 5.13. Example: 2x2 HBM Crossbars 5.14. Example: 16x16 Crossbar
5.3. Recommended NoC Design Topologies x
5.3.1. 1:1 Connectivity with EMIF and HBM 5.3.2. HBM Crossbars 5.3.3. Connectivity with HPS
6. Debugging the NoC x
6.1. Debugging NoC AXI Transaction Issues 6.2. Debugging NoC Bit Errors 6.3. Debugging NoC Performance Issues
6.3. Debugging NoC Performance Issues x
6.3.1. Measuring Performance with the Signal Tap Logic Analyzer 6.3.2. Measuring Performance with the Performance Monitor 6.3.3. Performance Debug Steps
1. Answers to Top FAQs
2. About This Application Note
3. Component Bandwidth Projections and Limitations
4. Resource Planning for Intel Agilex® 7 M-Series FPGAs
5. Factors Affecting NoC Performance
6. Debugging the NoC
7. Document Revision History of AN 1003: Multi Memory IP System Resource Planning for Intel Agilex® 7 M-Series FPGAs

4.4. Planning for Initiator Blockage Impact from GPIO, LVDS SERDES, and PHY Lite Bypass Mode

Low-speed I/O protocols, such as LVDS SERDES, PHY Lite, or GPIO IP functions bypass the hard memory NoC. Due to device routing limitations, you cannot simultaneously use these I/O functions and NoC initiators directly across from a I/O bank that uses these low-speed I/O functions.

It is essential to create an early estimate for GPIO, LVDS SERDES, and PHY Lite IP usage within a given I/O bank to evaluate the potential initiator blockage. If possible for your application, place these IP in the I/O banks on the left and right edge of the device to ensure that a centralized initiator is available to memories.

GPIO-B, LVDS SERDES, and PHY Lite blocks in certain byte lanes can cause the loss of NoC initiators across this I/O bank. Similarly, unplanned NoC initiator placement can prevent certain GPIO-B blocks from implementing functions. Unanticipated GPIO placement can severely impact the achievement of full bandwidth for EMIF or HBM2E systems.

General Purpose I/O functions in byte lane BL7 in pin index [48:88] block an initiator. Placing the same General Purpose I/O functions in byte lane BL7 in pin index [89:95] does not block any initiator.

Use the Interface Planner in the Intel® Quartus® Prime Pro Edition software to obtain an accurate view of the placement restrictions. Interface Planner displays the NoC initiator locations that are available and blocked.

Note: If using PHY Lite or LVDS SERDES mode and I/O pin index [95:88], this combination blocks an initiator in the current version of the Intel® Quartus® Prime Pro Edition software.
Level Two Title