Intel® Simics® Simulator for Intel® FPGAs: Intel Agilex® 5 E-Series Virtual Platform User Guide

Download PDF
ID 786901
Date 12/04/2023
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents
Document Table of Contents x
1. About This Document 2. Intel Agilex® 5 E-Series Intel® Simics® Virtual Platforms 3. Intel Agilex® 5 E-Series Virtual Platform Component Intel® Simics® Models 4. Running a Simulation with the Intel Agilex® 5 E-Series HPS Model 5. Supported Use Cases A. Document Revision History
1. About This Document x
1.1. Terminology 1.2. List of Acronyms
2. Intel Agilex® 5 E-Series Intel® Simics® Virtual Platforms x
2.1. Intel Agilex® 5 E-Series Universal Virtual Platform
2.1. Intel Agilex® 5 E-Series Universal Virtual Platform x
2.1.1. Intel Agilex® 5 E-Series Universal Virtual Platform Overview 2.1.2. Intel Agilex® 5 E-Series Universal Virtual Platform User-Configurable Parameters 2.1.3. Intel Agilex® 5 E-Series Virtual Platform Key Capabilities
2.1.1. Intel Agilex® 5 E-Series Universal Virtual Platform Overview x
2.1.1.1. Intel Agilex® 5 HPS Component 2.1.1.2. HPS Subsystem Component 2.1.1.3. FPGA Fabric Design 2.1.1.4. qsys_top Component 2.1.1.5. FPGA Component 2.1.1.6. Board Component 2.1.1.7. System Component 2.1.1.8. Target Script
2.1.3. Intel Agilex® 5 E-Series Virtual Platform Key Capabilities x
2.1.3.1. Boot-To-Operating System Prompt 2.1.3.2. Basic Ethernet 2.1.3.3. CPU Power-On and Boot Core Selection 2.1.3.4. Reset Flow 2.1.3.5. General Purpose I/O (GPIO) Loopback 2.1.3.6. USB Disks Hot-Plug Support 2.1.3.7. On-Chip Memory IP FPGA Fabric Example Design 2.1.3.8. FPGA-to-HPS Bridges
3. Intel Agilex® 5 E-Series Virtual Platform Component Intel® Simics® Models x
3.1. Intel Agilex® 5 E-Series HPS Intel® Simics® Model 3.2. Virtual Platform HPS Subsystem Components 3.3. Virtual Platform qsys_top Components 3.4. Virtual Platform Board Components
3.1. Intel Agilex® 5 E-Series HPS Intel® Simics® Model x
3.1.1. Intel Agilex® 5 E-Series HPS Intel® Simics® Model Architecture 3.1.2. PSS Subsystem Components 3.1.3. MPU and APS Subsystem 3.1.4. MPFE Subsystem 3.1.5. Additional Intel Agilex® 5 E-Series HPS Components
3.2. Virtual Platform HPS Subsystem Components x
3.2.1. External Memory Interface (EMIF) 3.2.2. Security Device Manager (SDM)
3.3. Virtual Platform qsys_top Components x
3.3.1. FPGA Fabric
3.4. Virtual Platform Board Components x
3.4.1. Marvel EMAC PHY 3.4.2. SD Card device 3.4.3. ONFI NAND Memory Device 3.4.4. SPI Flash Device 3.4.5. AT24Cxx EEPROM Device 3.4.6. I3C Device 3.4.7. USB Disk Device 3.4.8. Intel® Simics® Text Console
4. Running a Simulation with the Intel Agilex® 5 E-Series HPS Model x
4.1. Prerequisites 4.2. Intel® Simics® Simulation Setup for the Intel Agilex® 5 E-Series Device 4.3. Starting the Simulation 4.4. Getting Device Information from the Intel® Simics® Model
1. About This Document
2. Intel Agilex® 5 E-Series Intel® Simics® Virtual Platforms
3. Intel Agilex® 5 E-Series Virtual Platform Component Intel® Simics® Models
4. Running a Simulation with the Intel Agilex® 5 E-Series HPS Model
5. Supported Use Cases
A. Document Revision History

2.1.3.1. Boot-To-Operating System Prompt

The Intel Agilex® 5 E-Series Virtual Platform allows exercising the HPS software in all parts of the boot flow for Linux* and Zephyr* operating systems. It provides the Intel® Simics® model of all hardware components needed for the boot flow.

  • The exercised boot flow for Linux* operating systems goes from U-Boot SPL (FSBL) to Linux prompt passing through ATF and U-Boot (SSBL).
  • The exercised boot flow for Zephyr* operating systems goes from ATF to Zephyr*, which immediately launches the application to run.
You can exercise the boot flow from a flash device such as an SD Card, NAND flash, or QSPI flash. Booting from an SD Card is the default boot mode.
Note: In the 23.3 release, it has been identified that booting from QSPI with a JFFS2 format image is taking considerably more time when compared with booting from SD Card, NAND flash, or QSPI with UBIFS format. This issue will be fixed in a future release.

For this capability, the following user-configurable parameters from the target script are used:

  • Boot from SD Card: create_hps_sd_card = TRUE, fsbl_image_filename and sd_image_filename.
  • Boot from NAND: create_hps_sd_card = FALSE, fsbl_image_filename, nand_data_image_filename and nand_spare_image_filename.
  • Boot from QSPI: create_hps_sd_card = FALSE, fsbl_image_filename and qspi_image_filename.
Level Two Title