Intel® Stratix® 10 MX FPGA Development Kit User Guide

Download PDF
ID 683867
Date 6/15/2020
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. About the Intel® Quartus® Prime Software 2.2. Development Kit Package 2.3. Installing the Intel FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Applying Power to the Development Kit 3.2. Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Components Overview 4.2. Intel® MAX® 10 FPGA System Controller 4.3. Intel® MAX® 10 FPGA Power Manager 4.4. FPGA Configuration 4.5. Status and User I/O Elements 4.6. Interfaces and Ports 4.7. HiLo Daughter Cards 4.8. Clocks 4.9. Power
4.6. Interfaces and Ports x
4.6.1. PCI Express 4.6.2. Memory Interface 4.6.3. High Bandwidth Memory (HBM2) 4.6.4. QSFP 4.6.5. I2C Flash Memory
4.6.2. Memory Interface x
4.6.2.1. On-board DDR4 Memory Interface 4.6.2.2. DDR4/DDR-T DIMM Memory Interface 4.6.2.3. HiLo Memory Interface
4.7. HiLo Daughter Cards x
4.7.1. DDR4 4.7.2. QDR-IV
4.9. Power x
4.9.1. Power Guidelines 4.9.2. Power Distribution System 4.9.3. Power Sequence 4.9.4. Power Measurement 4.9.5. Power Fast Discharging 4.9.6. Thermal Limitations and Protection 4.9.7. Cooling Design 4.9.8. Mechanical Information 4.9.9. Top Cover Removal
5. Board Test System x
5.1. Preparing the Board Running the Board Test System 5.3. Using the Board Test System
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The Sys Info Tab 5.3.3. The QSFP Tab 5.3.4. The PCIE Tab 5.3.5. The Component DDR4 Tab 5.3.6. The HiLo DDR4 Tab 5.3.7. The DDR4 Dimm Tab Start Stop Performance Indicators Error Control Address Range 5.3.8. The HBM2 Top Tab 5.3.9. The HBM2 Bottom Tab 5.3.10. Power Monitor 5.3.11. Clock Controller
A. Additional Information x
A.1. Add SmartVID settings in the QSF file A.2. Safety and Regulatory Information A.3. Compliance and Conformity Statement
A.2. Safety and Regulatory Information x
A.2.1. Safety Warnings A.2.2. Safety Cautions
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

5.3.7. The DDR4 Dimm Tab

This tab allows you to read and write Dual Inline Memory Module (DIMM) DDR4 memory on your board.

Figure 28. The DDR4 Dimm Tab

The following sections describe the controls on the DDR4 tab.

Start

Initiates DDR4 memory transaction performance analysis.

Stop

Terminates transaction performance analysis.

Performance Indicators

These controls display current transaction performance analysis information collected since you last clicked Start:
  • Write, Read and Total performance bars: Show the percentage of maximum theoretical data rate that the requested transactions are able to achieve.
  • Write (MBps), Read (MBps) and Total (MBps): Show the number of bytes analyzed per second.
  • Data Bus: 72 bits (8 bits ECC) wide and the frequency is 1066 MHz double data rate. 2133 Mbps per pin. Equating to a theoretical maximum bandwidth of 136,512 Mbps or 17,064 MBps.

Error Control

This control displays data errors detected during analysis and allows you to insert errors:
  • Detected errors: Displays the number of data errors detected in the hardware.
  • Inserted errors: Displays the number of errors inserted into the transaction stream.
  • Insert: Inserts a one-word error into the transaction stream each time you click the button. Insert Error is only enabled during transaction performance analysis.
  • Clear: Resets the detected error and inserted error counters to zeroes.

Address Range

Determines the number of addresses to use in each iteration of reads and writes.

Level Two Title