Intel® Stratix® 10 MX FPGA Development Kit User Guide

Download PDF
ID 683867
Date 6/15/2020
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. About the Intel® Quartus® Prime Software 2.2. Development Kit Package 2.3. Installing the Intel FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Applying Power to the Development Kit 3.2. Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Components Overview 4.2. Intel® MAX® 10 FPGA System Controller 4.3. Intel® MAX® 10 FPGA Power Manager 4.4. FPGA Configuration 4.5. Status and User I/O Elements 4.6. Interfaces and Ports 4.7. HiLo Daughter Cards 4.8. Clocks 4.9. Power
4.6. Interfaces and Ports x
4.6.1. PCI Express 4.6.2. Memory Interface 4.6.3. High Bandwidth Memory (HBM2) 4.6.4. QSFP 4.6.5. I2C Flash Memory
4.6.2. Memory Interface x
4.6.2.1. On-board DDR4 Memory Interface 4.6.2.2. DDR4/DDR-T DIMM Memory Interface 4.6.2.3. HiLo Memory Interface
4.7. HiLo Daughter Cards x
4.7.1. DDR4 4.7.2. QDR-IV
4.9. Power x
4.9.1. Power Guidelines 4.9.2. Power Distribution System 4.9.3. Power Sequence 4.9.4. Power Measurement 4.9.5. Power Fast Discharging 4.9.6. Thermal Limitations and Protection 4.9.7. Cooling Design 4.9.8. Mechanical Information 4.9.9. Top Cover Removal
5. Board Test System x
5.1. Preparing the Board Running the Board Test System 5.3. Using the Board Test System
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The Sys Info Tab 5.3.3. The QSFP Tab 5.3.4. The PCIE Tab 5.3.5. The Component DDR4 Tab 5.3.6. The HiLo DDR4 Tab 5.3.7. The DDR4 Dimm Tab 5.3.8. The HBM2 Top Tab 5.3.9. The HBM2 Bottom Tab 5.3.10. Power Monitor 5.3.11. Clock Controller
A. Additional Information x
A.1. Add SmartVID settings in the QSF file A.2. Safety and Regulatory Information A.3. Compliance and Conformity Statement
A.2. Safety and Regulatory Information x
A.2.1. Safety Warnings A.2.2. Safety Cautions
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

4.9.4. Power Measurement

Power measurements are provided for six FPGA power rails by using an ADC and sense resistors. The sense resistors are connected in series to the power regulator output. The I2C interface of the ADC or the regulators are used to sense the voltages. The I2C are connected to the Intel® MAX® 10 device for reading the voltage. Current reading is achieved by a LTC2497 reading the voltage drop across the sense resistor and software converts the voltage readings to current for each measured rail.

The following power rails are monitored:
  1. VCC, VCCP (Power sensing by I2C on LTC3884)
  2. VCCRERAM (Sense resistor R424, monitoring via LTC2497, U28)
  3. VCCRL (Sense resistor R437, monitoring via LTC2497, U28)
  4. VCCRR (Sense resistor R450, monitoring via LTC2497, U28)
  5. VCCT (Sense resistor R463, monitoring via LTC2497, U28)
  6. VCCIO_UIB (Power sensing by I2C on EM2120L, U51)
  7. 3.3V (Power sensing by I2C on EM2130H, U43)
Figure 16. Power Measurement
Level Two Title