Intel® Stratix® 10 MX FPGA Development Kit User Guide

Download PDF
ID 683867
Date 6/15/2020
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. About the Intel® Quartus® Prime Software 2.2. Development Kit Package 2.3. Installing the Intel FPGA Download Cable Driver
3. Development Kit Setup x
3.1. Applying Power to the Development Kit 3.2. Default Switch and Jumper Settings
4. Development Kit Components x
4.1. Components Overview 4.2. Intel® MAX® 10 FPGA System Controller 4.3. Intel® MAX® 10 FPGA Power Manager 4.4. FPGA Configuration 4.5. Status and User I/O Elements 4.6. Interfaces and Ports 4.7. HiLo Daughter Cards 4.8. Clocks 4.9. Power
4.6. Interfaces and Ports x
4.6.1. PCI Express 4.6.2. Memory Interface 4.6.3. High Bandwidth Memory (HBM2) 4.6.4. QSFP 4.6.5. I2C Flash Memory
4.6.2. Memory Interface x
4.6.2.1. On-board DDR4 Memory Interface 4.6.2.2. DDR4/DDR-T DIMM Memory Interface 4.6.2.3. HiLo Memory Interface
4.7. HiLo Daughter Cards x
4.7.1. DDR4 4.7.2. QDR-IV
4.9. Power x
4.9.1. Power Guidelines 4.9.2. Power Distribution System 4.9.3. Power Sequence 4.9.4. Power Measurement 4.9.5. Power Fast Discharging 4.9.6. Thermal Limitations and Protection 4.9.7. Cooling Design 4.9.8. Mechanical Information 4.9.9. Top Cover Removal
5. Board Test System x
5.1. Preparing the Board Running the Board Test System 5.3. Using the Board Test System
5.3. Using the Board Test System x
5.3.1. The Configure Menu 5.3.2. The Sys Info Tab 5.3.3. The QSFP Tab 5.3.4. The PCIE Tab 5.3.5. The Component DDR4 Tab 5.3.6. The HiLo DDR4 Tab 5.3.7. The DDR4 Dimm Tab 5.3.8. The HBM2 Top Tab 5.3.9. The HBM2 Bottom Tab 5.3.10. Power Monitor 5.3.11. Clock Controller
A. Additional Information x
A.1. Add SmartVID settings in the QSF file A.2. Safety and Regulatory Information A.3. Compliance and Conformity Statement
A.2. Safety and Regulatory Information x
A.2.1. Safety Warnings A.2.2. Safety Cautions
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

3.1. Applying Power to the Development Kit

This development kit is designed to operate in two modes:

As a PCIe* add-in card

When operating the card as a PCIe* system, insert the card into an available PCIe* slot and connect a 2x4 pin PCIe* power cable from the system to the power connectors at Aux power connector J11 of the board.

Note: When operating as a PCIe* add-in card, the board does not power on unless power is supplied to J11.

In bench-top mode

In bench-top mode, you must supply the board with the provided 240 W power supply connected to the Aux power connector J11, as follows

Note: This development board ships with its switches preconfigured to support the design examples in the kit. If you suspect that your board may not be correctly configured with the default settings, follow the instructions in the Default Switch and Jumper Settings of this chapter.
  1. Connect the provided power supply to an outlet and the DC Power Jack (J11) on the FPGA board.
    Note: Use only the supplied power supply. Power regulation circuits on the board can be damaged by power supplies with greater voltage.
  2. Set the power switch (SW3) to the ON position.

When the board powers up, the blue power LED illuminates and the board is ready for use.

Level Two Title