Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 9/30/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Timing Analysis Introduction 2. Using the Quartus® Prime Timing Analyzer A. Quartus® Prime Pro Edition User Guides
1. Timing Analysis Introduction x
1.1. What's New In This Version 1.2. Timing Analysis Basic Concepts 1.3. Timing Analysis Overview Document Revision History
1.2. Timing Analysis Basic Concepts x
1.2.1. Timing Path and Clock Analysis 1.2.2. Clock Setup Analysis 1.2.3. Clock Hold Analysis 1.2.4. Recovery and Removal Analysis 1.2.5. Multicycle Path Analysis 1.2.6. Metastability Analysis 1.2.7. Timing Pessimism 1.2.8. Clock-As-Data Analysis 1.2.9. Multicorner Timing Analysis 1.2.10. Time Borrowing
1.2.1. Timing Path and Clock Analysis x
1.2.1.1. The Timing Netlist 1.2.1.2. Timing Paths 1.2.1.3. Data and Clock Arrival Times 1.2.1.4. Launch and Latch Edges
1.2.5. Multicycle Path Analysis x
1.2.5.1. Multicycle Clock Hold 1.2.5.2. Multicycle Clock Setup
1.2.10. Time Borrowing x
1.2.10.1. Time Borrowing Limitations 1.2.10.2. Time Borrowing with Latches 1.2.10.3. Enabling Time Borrowing Optimization
2. Using the Quartus® Prime Timing Analyzer x
2.1. Using Timing Constraints throughout the Design Flow 2.2. Timing Analysis Flow 2.3. Applying Timing Constraints 2.4. Timing Constraint Descriptions 2.5. Timing Report Descriptions 2.6. Scripting Timing Analysis 2.7. Using the Quartus® Prime Timing Analyzer Document Revision History 2.8. Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
2.2. Timing Analysis Flow x
2.2.1. Step 1: Specify General Timing Analyzer Settings 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Run the Timing Analyzer 2.2.4. Step 4: Analyze Timing Reports
2.2.2. Step 2: Specify Timing Constraints x
2.2.2.1. Specifying SDC-on-RTL Timing Constraints 2.2.2.2. Specifying Conventional SDC Timing Constraints 2.2.2.3. Specifying Synthesis-Only SDC Timing Constraints
2.2.3. Step 3: Run the Timing Analyzer x
2.2.3.1. Running Post-Synthesis Early Timing Analysis 2.2.3.2. Running Post-Fit Timing Analysis
2.2.3.2. Running Post-Fit Timing Analysis x
2.2.3.2.1. Setting the Operating Conditions for Timing Analysis 2.2.3.2.2. Promoting Critical Warnings to Errors
2.2.4. Step 4: Analyze Timing Reports x
2.2.4.1. Cross-Probing with Design Assistant 2.2.4.2. Launching Design Assistant from Timing Analyzer 2.2.4.3. Locating Timing Paths in Other Tools 2.2.4.4. Correlating Constraints to the Timing Report
2.2.4.1. Cross-Probing with Design Assistant x
2.2.4.1.1. Cross-Probing from Design Assistant to Timing Analyzer
2.3. Applying Timing Constraints x
2.3.1. Recommended Initial Conventional SDC Constraints 2.3.2. Example Circuit and Conventional SDC File 2.3.3. SDC File Precedence 2.3.4. Iteratively Modifying Constraints 2.3.5. Applying Entity-Bound Timing Constraints 2.3.6. Constraining Design Partition Ports 2.3.7. Using Fitter Overconstraints
2.3.1. Recommended Initial Conventional SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.5. Applying Entity-Bound Timing Constraints x
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints 2.3.5.2. Using Entity-Bound SDC Files
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints x
2.3.5.1.1. Targeting Constraints to Module Inputs and Outputs 2.3.5.1.2. Entity Based SDC-on-RTL Constraint Scope 2.3.5.1.3. Automatic Scope Example for SDC-on-RTL 2.3.5.1.4. Manual Scope Example for SDC-on-RTL
2.3.5.2. Using Entity-Bound SDC Files x
2.3.5.2.1. Entity-Bound SDC Constraint Scope 2.3.5.2.2. Automatic Scope Entity-bound Constraint Example 2.3.5.2.3. Manual Scope Entity-bound Constraint Example 2.3.5.2.4. Exporting a Design Partition with Entity-bound Constraints 2.3.5.2.5. Importing a Design Partition with Entity-bound Constraints
2.3.6. Constraining Design Partition Ports x
2.3.6.1. Timing Analysis of Imported Compilation Results
2.4. Timing Constraint Descriptions x
2.4.1. Clock Constraints 2.4.2. I/O Constraints 2.4.3. Delay and Skew Constraints 2.4.4. Timing Exception Constraints 2.4.5. Delay Annotation
2.4.1. Clock Constraints x
2.4.1.1. Creating Base Clocks 2.4.1.2. Creating Virtual Clocks 2.4.1.3. Creating Generated Clocks (create_generated_clock) 2.4.1.4. Deriving PLL Clocks 2.4.1.5. Creating Clock Groups (set_clock_groups) 2.4.1.6. Accounting for Clock Effect Characteristics 2.4.1.7. Constraining CDC Paths
2.4.1.1. Creating Base Clocks x
2.4.1.1.1. Automatic Clock Detection and Constraint Creation
2.4.1.2. Creating Virtual Clocks x
2.4.1.2.1. Specifying I/O Interface Uncertainty 2.4.1.2.2. I/O Interface Clock Uncertainty Example
2.4.1.3. Creating Generated Clocks (create_generated_clock) x
2.4.1.3.1. Clock Divider Example (-divide_by) 2.4.1.3.2. Clock Multiplexer Example
2.4.1.5. Creating Clock Groups (set_clock_groups) x
2.4.1.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 2.4.1.5.2. Asynchronous Clock Groups (-asynchronous) 2.4.1.5.3. set_clock_groups Constraint Tips
2.4.1.6. Accounting for Clock Effect Characteristics x
2.4.1.6.1. Set Clock Latency (set_clock_latency) 2.4.1.6.2. Clock Uncertainty
2.4.2. I/O Constraints x
2.4.2.1. Deprecation of the blackbox Argument 2.4.2.2. Input Constraints (set_input_delay) 2.4.2.3. Output Constraints (set_output_delay)
2.4.3. Delay and Skew Constraints x
2.4.3.1. Advanced I/O Timing and Board Trace Model Delay 2.4.3.2. Maximum Skew (set_max_skew) 2.4.3.3. Net Delay (set_net_delay) 2.4.3.4. Data Delay (set_data_delay)
2.4.4. Timing Exception Constraints x
2.4.4.1. Timing Exception Precedence 2.4.4.2. False Paths (set_false_path) 2.4.4.3. Minimum and Maximum Delays 2.4.4.4. Multicycle Paths 2.4.4.5. Multicycle Exception Examples 2.4.4.6. Creating Efficient Timing Exceptions
2.4.4.4. Multicycle Paths x
2.4.4.4.1. Common Multicycle Applications 2.4.4.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.4.4.4.3. Accounting for a Phase Shift (-phase)
2.4.4.5. Multicycle Exception Examples x
2.4.4.5.1. Default Multicycle Analysis 2.4.4.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.4.4.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.4.4.5.4. Same Frequency Clocks with Destination Clock Offset 2.4.4.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.4.4.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.4.4.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.4.4.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.5. Timing Report Descriptions x
2.5.1. Report Fmax Summary 2.5.2. Report Timing 2.5.3. Report Timing By Source Files 2.5.4. Report Data Delay 2.5.5. Report Net Delay 2.5.6. Report Clocks and Clock Network 2.5.7. Report Clock Transfers 2.5.8. Report Metastability 2.5.9. Report CDC Viewer 2.5.10. Report Asynchronous CDC 2.5.11. Report Logic Depth 2.5.12. Report Neighbor Paths 2.5.13. Report Register Spread 2.5.14. Report Route Net of Interest 2.5.15. Report Retiming Restrictions 2.5.16. Report Register Statistics 2.5.17. Report Pipelining Information 2.5.18. Report Time Borrowing Data 2.5.19. Report Exceptions and Exceptions Reachability 2.5.20. Report Bottlenecks 2.5.21. Check Timing 2.5.22. Report SDC
2.5.13. Report Register Spread x
2.5.13.1. Registers with High Timing Path Endpoint Tension 2.5.13.2. Registers with High Immediate Fan-Out Tension
2.5.20. Report Bottlenecks x
2.5.20.1. Specifying Custom Bottleneck Criteria
2.6. Scripting Timing Analysis x
2.6.1. The quartus_sta Executable 2.6.2. The quartus_staw Executable 2.6.3. Collection Commands
2.6.3. Collection Commands x
2.6.3.1. Wildcard Characters 2.6.3.2. Adding and Removing Collection Items 2.6.3.3. Query of Collections 2.6.3.4. Using the get_pins Command
Answers to Top FAQs
1. Timing Analysis Introduction
2. Using the Quartus® Prime Timing Analyzer
A. Quartus® Prime Pro Edition User Guides

2.3.6. Constraining Design Partition Ports

You can assign clock definitions and SDC exceptions to design partition ports. The block-based design and partial reconfiguration design flows require the use of design partitions.
Note: Beginning in Quartus® Prime Pro Edition software version 24.3, support for the blackbox argument is removed. You could previously use the blackbox to perform delay budgeting on I/Os at the boundary of a design partition. Refer to Deprecation of the blackbox Argument.

The Compiler represents design partition ports in your timing netlist as combinational nodes with persistent names that the Compiler cannot optimize away. You can safely refer to these ports as clock sources or -through points in SDC constraints. You can also use design partition port names as -to and -from points in the report_path command.

If a port on partition_a has the name clk_divide, then the SDC constraint is: 

create_generated_clock –source clock -divide_by 2 \
     top|partition_a|clk_divide

If a set of ports on partition_b has the name data_input[0..7], then the SDC constraint is: 

set_multicycle_path –from top|partition_a|data_reg* \
     -through top|partition_b|data_input* 2

You can use multiple -through clauses. This technique allows you to specify paths that go through output ports of one design partition, and then through the input ports of another, downstream design partition.

To add constraints to partition ports:

  1. Run Analysis & Synthesis or run full compilation on a design containing design partitions.
  2. To open the RTL Viewer and locate the partition ports of interest, click Tools > Netlist Viewers > RTL Viewer.
  3. Using the same names as the RTL Viewer, add clock and other SDC constraints to the .sdc file for your project. You can use wildcards to refer to more than one port.
  4. Recompile the design to apply the new definitions and constraints.

    Aside from block-based and PR flows, this technique also aids in emulation of ASICs using FPGAs. In this type of design, clock networks often span multiple hierarchies of partitions. Typically, designers remove the clock-dividing circuitry from the netlist, since they cannot easily emulate this circuitry on Intel FPGAs. For such clock networks, this technique allows you to define different versions of the clock signal in places where the circuitry is removed.

    You must design and place your partitions strategically, and then define the appropriate ports on these partitions. Ensure that your ports and partitions coincide with the part of the clock network which contains the special circuitry. You can manually edit the emulated ASIC netlist to annotate appropriate clock definitions and clock relationships. You can also use this technique in any projects where arbitrary locations on paths require constrained timing or defined clock sources.


Section Content
Timing Analysis of Imported Compilation Results

Related Information
Level Two Title