Quartus® Prime Pro Edition User Guide: Timing Analyzer

Download PDF
ID 683243
Date 9/30/2024
Public
Document Table of Contents
Document Table of Contents x
Answers to Top FAQs 1. Timing Analysis Introduction 2. Using the Quartus® Prime Timing Analyzer A. Quartus® Prime Pro Edition User Guides
1. Timing Analysis Introduction x
1.1. What's New In This Version 1.2. Timing Analysis Basic Concepts 1.3. Timing Analysis Overview Document Revision History
1.2. Timing Analysis Basic Concepts x
1.2.1. Timing Path and Clock Analysis 1.2.2. Clock Setup Analysis 1.2.3. Clock Hold Analysis 1.2.4. Recovery and Removal Analysis 1.2.5. Multicycle Path Analysis 1.2.6. Metastability Analysis 1.2.7. Timing Pessimism 1.2.8. Clock-As-Data Analysis 1.2.9. Multicorner Timing Analysis 1.2.10. Time Borrowing
1.2.1. Timing Path and Clock Analysis x
1.2.1.1. The Timing Netlist 1.2.1.2. Timing Paths 1.2.1.3. Data and Clock Arrival Times 1.2.1.4. Launch and Latch Edges
1.2.5. Multicycle Path Analysis x
1.2.5.1. Multicycle Clock Hold 1.2.5.2. Multicycle Clock Setup
1.2.10. Time Borrowing x
1.2.10.1. Time Borrowing Limitations 1.2.10.2. Time Borrowing with Latches 1.2.10.3. Enabling Time Borrowing Optimization
2. Using the Quartus® Prime Timing Analyzer x
2.1. Using Timing Constraints throughout the Design Flow 2.2. Timing Analysis Flow 2.3. Applying Timing Constraints 2.4. Timing Constraint Descriptions 2.5. Timing Report Descriptions 2.6. Scripting Timing Analysis 2.7. Using the Quartus® Prime Timing Analyzer Document Revision History 2.8. Quartus® Prime Pro Edition User Guide: Timing Analyzer Archive
2.2. Timing Analysis Flow x
2.2.1. Step 1: Specify General Timing Analyzer Settings 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Run the Timing Analyzer 2.2.4. Step 4: Analyze Timing Reports
2.2.2. Step 2: Specify Timing Constraints x
2.2.2.1. Specifying SDC-on-RTL Timing Constraints 2.2.2.2. Specifying Conventional SDC Timing Constraints 2.2.2.3. Specifying Synthesis-Only SDC Timing Constraints
2.2.3. Step 3: Run the Timing Analyzer x
2.2.3.1. Running Post-Synthesis Early Timing Analysis 2.2.3.2. Running Post-Fit Timing Analysis
2.2.3.2. Running Post-Fit Timing Analysis x
2.2.3.2.1. Setting the Operating Conditions for Timing Analysis 2.2.3.2.2. Promoting Critical Warnings to Errors
2.2.4. Step 4: Analyze Timing Reports x
2.2.4.1. Cross-Probing with Design Assistant 2.2.4.2. Launching Design Assistant from Timing Analyzer 2.2.4.3. Locating Timing Paths in Other Tools 2.2.4.4. Correlating Constraints to the Timing Report
2.2.4.1. Cross-Probing with Design Assistant x
2.2.4.1.1. Cross-Probing from Design Assistant to Timing Analyzer
2.3. Applying Timing Constraints x
2.3.1. Recommended Initial Conventional SDC Constraints 2.3.2. Example Circuit and Conventional SDC File 2.3.3. SDC File Precedence 2.3.4. Iteratively Modifying Constraints 2.3.5. Applying Entity-Bound Timing Constraints 2.3.6. Constraining Design Partition Ports 2.3.7. Using Fitter Overconstraints
2.3.1. Recommended Initial Conventional SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.5. Applying Entity-Bound Timing Constraints x
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints 2.3.5.2. Using Entity-Bound SDC Files
2.3.5.1. Using Entity-Based SDC-on-RTL Constraints x
2.3.5.1.1. Targeting Constraints to Module Inputs and Outputs 2.3.5.1.2. Entity Based SDC-on-RTL Constraint Scope 2.3.5.1.3. Automatic Scope Example for SDC-on-RTL 2.3.5.1.4. Manual Scope Example for SDC-on-RTL
2.3.5.2. Using Entity-Bound SDC Files x
2.3.5.2.1. Entity-Bound SDC Constraint Scope 2.3.5.2.2. Automatic Scope Entity-bound Constraint Example 2.3.5.2.3. Manual Scope Entity-bound Constraint Example 2.3.5.2.4. Exporting a Design Partition with Entity-bound Constraints 2.3.5.2.5. Importing a Design Partition with Entity-bound Constraints
2.3.6. Constraining Design Partition Ports x
2.3.6.1. Timing Analysis of Imported Compilation Results
2.4. Timing Constraint Descriptions x
2.4.1. Clock Constraints 2.4.2. I/O Constraints 2.4.3. Delay and Skew Constraints 2.4.4. Timing Exception Constraints 2.4.5. Delay Annotation
2.4.1. Clock Constraints x
2.4.1.1. Creating Base Clocks 2.4.1.2. Creating Virtual Clocks 2.4.1.3. Creating Generated Clocks (create_generated_clock) 2.4.1.4. Deriving PLL Clocks 2.4.1.5. Creating Clock Groups (set_clock_groups) 2.4.1.6. Accounting for Clock Effect Characteristics 2.4.1.7. Constraining CDC Paths
2.4.1.1. Creating Base Clocks x
2.4.1.1.1. Automatic Clock Detection and Constraint Creation
2.4.1.2. Creating Virtual Clocks x
2.4.1.2.1. Specifying I/O Interface Uncertainty 2.4.1.2.2. I/O Interface Clock Uncertainty Example
2.4.1.3. Creating Generated Clocks (create_generated_clock) x
2.4.1.3.1. Clock Divider Example (-divide_by) 2.4.1.3.2. Clock Multiplexer Example
2.4.1.5. Creating Clock Groups (set_clock_groups) x
2.4.1.5.1. Exclusive Clock Groups (-logically_exclusive or -physically_exclusive) 2.4.1.5.2. Asynchronous Clock Groups (-asynchronous) 2.4.1.5.3. set_clock_groups Constraint Tips
2.4.1.6. Accounting for Clock Effect Characteristics x
2.4.1.6.1. Set Clock Latency (set_clock_latency) 2.4.1.6.2. Clock Uncertainty
2.4.2. I/O Constraints x
2.4.2.1. Deprecation of the blackbox Argument 2.4.2.2. Input Constraints (set_input_delay) 2.4.2.3. Output Constraints (set_output_delay)
2.4.3. Delay and Skew Constraints x
2.4.3.1. Advanced I/O Timing and Board Trace Model Delay 2.4.3.2. Maximum Skew (set_max_skew) 2.4.3.3. Net Delay (set_net_delay) 2.4.3.4. Data Delay (set_data_delay)
2.4.4. Timing Exception Constraints x
2.4.4.1. Timing Exception Precedence 2.4.4.2. False Paths (set_false_path) 2.4.4.3. Minimum and Maximum Delays 2.4.4.4. Multicycle Paths 2.4.4.5. Multicycle Exception Examples 2.4.4.6. Creating Efficient Timing Exceptions
2.4.4.4. Multicycle Paths x
2.4.4.4.1. Common Multicycle Applications 2.4.4.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.4.4.4.3. Accounting for a Phase Shift (-phase)
2.4.4.5. Multicycle Exception Examples x
2.4.4.5.1. Default Multicycle Analysis 2.4.4.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.4.4.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.4.4.5.4. Same Frequency Clocks with Destination Clock Offset 2.4.4.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.4.4.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.4.4.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.4.4.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.5. Timing Report Descriptions x
2.5.1. Report Fmax Summary 2.5.2. Report Timing 2.5.3. Report Timing By Source Files 2.5.4. Report Data Delay 2.5.5. Report Net Delay 2.5.6. Report Clocks and Clock Network 2.5.7. Report Clock Transfers 2.5.8. Report Metastability 2.5.9. Report CDC Viewer 2.5.10. Report Asynchronous CDC 2.5.11. Report Logic Depth 2.5.12. Report Neighbor Paths 2.5.13. Report Register Spread 2.5.14. Report Route Net of Interest 2.5.15. Report Retiming Restrictions 2.5.16. Report Register Statistics 2.5.17. Report Pipelining Information 2.5.18. Report Time Borrowing Data 2.5.19. Report Exceptions and Exceptions Reachability 2.5.20. Report Bottlenecks 2.5.21. Check Timing 2.5.22. Report SDC
2.5.13. Report Register Spread x
2.5.13.1. Registers with High Timing Path Endpoint Tension 2.5.13.2. Registers with High Immediate Fan-Out Tension
2.5.20. Report Bottlenecks x
2.5.20.1. Specifying Custom Bottleneck Criteria
2.6. Scripting Timing Analysis x
2.6.1. The quartus_sta Executable 2.6.2. The quartus_staw Executable 2.6.3. Collection Commands
2.6.3. Collection Commands x
2.6.3.1. Wildcard Characters 2.6.3.2. Adding and Removing Collection Items 2.6.3.3. Query of Collections 2.6.3.4. Using the get_pins Command
Answers to Top FAQs
1. Timing Analysis Introduction
2. Using the Quartus® Prime Timing Analyzer
A. Quartus® Prime Pro Edition User Guides

2.4.4.4. Multicycle Paths

By default, the Timing Analyzer performs a single-cycle analysis, which is the most restrictive type of analysis. When analyzing a path without a multicycle constraint, the Timing Analyzer determines the setup launch and latch edge times by identifying the closest two active edges in the respective waveforms.
Figure 98. Default Setup and Hold Relationship (No Multicycle)

For hold time analysis, the timing analyzer analyzes the path for two timing conditions for every possible setup relationship, not just the worst-case setup relationship. Therefore, the hold launch and latch times can be unrelated to the setup launch and latch edges.

A multicycle constraint adjusts this default setup or hold relationship by the number of clock cycles you specify, based on the source (-start) or destination (-end) clock. A setup multicycle constraint of 2 extends the worst-case setup latch edge by one destination clock period. If you do not specify -start and -end values, the default constraint is -end.

Figure 99. Setup and Hold Relationship with Multicycle = 2

Hold multicycle constraints derive from the default hold position (the default value is 0). An end hold multicycle constraint of 1 effectively subtracts one destination clock period from the default hold latch edge.

When the objects are timing nodes, the multicycle constraint only applies to the path between the two nodes. When an object is a clock, the multicycle constraint applies to all paths where the source node (-from) or destination node (-to) is clocked by the clock. When you adjust a setup relationship with a multicycle constraint, the default hold relationship adjusts automatically.

You can use timing constraints to modify either the launch or latch edge times that the Timing Analyzer uses to determine a setup relationship or hold relationship.

Table 23.  Multicycle Constraints
Command Modification
set_multicycle_path -setup -end <value> Latch edge time of the setup relationship.
set_multicycle_path -setup -start<value> Launch edge time of the setup relationship.
set_multicycle_path -hold -end <value> Latch edge time of the hold relationship.
set_multicycle_path -hold -start <value> Launch edge time of the hold relationship.

Verify correct implementation of timing exception assignments by using the Report Exceptions (report_exceptions) command to report all exceptions to default timing analysis conditions.


Section Content
Common Multicycle Applications
Relaxing Setup with Multicycle (set_multicyle_path)
Accounting for a Phase Shift (-phase)

Related Information
Level Two Title