Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide

Download PDF
ID 820977
Date 7/12/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. HPS Boot 8. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash U24 with Default Factory Image 3.3.2. Restoring SD Card with the Default Factory Image
4. Board Test System x
4.1. Setting Up BTS GUI Running Environment 4.2. Troubleshooting for Launching BTS 4.3. BTS Functionalities
4.1. Setting Up BTS GUI Running Environment x
4.1.1. Installing Quartus® Prime Software 4.1.2. Running the BTS GUI
4.3. BTS Functionalities x
4.3.1. The Clock Functionality 4.3.2. The Power Functionality 4.3.3. The MAX® 10 Functionality 4.3.4. Agilex™ 5 FPGA Functionality 4.3.5. Other Functionalities
4.3.1. The Clock Functionality x
4.3.1.1. Si5332 4.3.1.2. Si5518 4.3.1.3. Si549 4.3.1.4. Si569 4.3.1.5. Si52202
4.3.2. The Power Functionality x
4.3.2.1. Power Monitor 4.3.2.2. Temperature Monitor
4.3.3. The MAX® 10 Functionality x
4.3.3.1. The System Tab 4.3.3.2. The IO Control Tab
4.3.4. Agilex™ 5 FPGA Functionality x
4.3.4.1. The Configure Menu 4.3.4.2. The Main Info Tab 4.3.4.3. The Transceiver Tab 4.3.4.4. The Memory Tab
4.3.4.3. The Transceiver Tab x
4.3.4.3.1. The FMC+ Tab 4.3.4.3.2. The SFP+ Tab
4.3.4.3.1. The FMC+ Tab x
4.3.4.3.1.1. The FMC+ Test Tab 4.3.4.3.1.2. The FMC+ Status Tab
4.3.4.4. The Memory Tab x
4.3.4.4.1. The COMP0 Tab 4.3.4.4.2. The COMP1 Tab 4.3.4.4.3. The HPS COMP Tab
4.3.5. Other Functionalities x
4.3.5.1. The Diagnostic Functionality 4.3.5.2. The Sys Info 4.3.5.3. The Connection Information 4.3.5.4. The Bottom Info Bar
5. Development Kit Hardware and Configuration x
5.1. Configuring the FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring the FPGA Device by Active Serial (AS) Modes (Default Mode)
6. Custom Projects for the Development Kit x
6.1. Golden Top 6.2. EMIF Pin Swizzling Setting
A. Development Kit Components x
A.1. Board Overview A.2. System Management A.3. Power A.4. Clocks A.5. General Input/Output A.6. Memory Interfaces A.7. Board to Board Connector A.8. Communication Interfaces
A.1. Board Overview x
A.1.1. Board Components
A.7. Board to Board Connector x
A.7.1. Modular Board Primary Connector A.7.2. Modular Board Secondary Connector A.7.3. Carrier Board Primary Connector A.7.4. Carrier Board Secondary Connector
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. HPS Boot
8. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide
A. Development Kit Components
B. Additional Information

4.3.1.1. Si5332

Figure 9. The Si5332 Setting Page
  • Read: Reads the current frequency setting for the oscillator associated with the active tab.
  • Set: Sets the programmable oscillator frequency for the selected clock to the value in the OUTx output controls. Frequency changes might take several milliseconds to take effect. Altera recommends resetting the FPGA logic after changing frequencies.
  • Import: Imports the register list generated from the tool of the Skyworks* Clockbuilder Pro software. Register changes are volatile after power cycling.
  • Default: Sets the frequency for the oscillator associated with the active tab back to its default value. This can also be accomplished by power cycling the board.
  • Configuration Save: Clock GUI supports to save the configuration to flash if you want the board to load the user settings on power-up next time. To do so, follow these steps:
    1. Select the Configuration Save checkbox.
    2. Click the Import or Set button to change the clock frequency setting, meanwhile the new configuration is saved in flash.
    You can also erase the configuration in flash by following these steps:
    1. Select the Configuration Save checkbox.
    2. Click the Default button to change the clock frequency setting to default value and erase the flash.
Related Information
Level Two Title