Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide

Download PDF
ID 820977
Date 7/12/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Board Test System 5. Development Kit Hardware and Configuration 6. Custom Projects for the Development Kit 7. HPS Boot 8. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide A. Development Kit Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Feature Summary 1.3. Box Contents 1.4. Recommended Operating Conditions
2. Getting Started x
2.1. Quartus® Prime Software and Driver Installation 2.2. Quick Start Guide 2.3. Design Examples
3. Development Kit Setup x
3.1. Default Settings 3.2. Powering Up the Development Kit 3.3. Performing Board Restore
3.3. Performing Board Restore x
3.3.1. Restoring Board QSPI Flash U24 with Default Factory Image 3.3.2. Restoring SD Card with the Default Factory Image
4. Board Test System x
4.1. Setting Up BTS GUI Running Environment 4.2. Troubleshooting for Launching BTS 4.3. BTS Functionalities
4.1. Setting Up BTS GUI Running Environment x
4.1.1. Installing Quartus® Prime Software 4.1.2. Running the BTS GUI
4.3. BTS Functionalities x
4.3.1. The Clock Functionality 4.3.2. The Power Functionality 4.3.3. The MAX® 10 Functionality 4.3.4. Agilex™ 5 FPGA Functionality 4.3.5. Other Functionalities
4.3.1. The Clock Functionality x
4.3.1.1. Si5332 4.3.1.2. Si5518 4.3.1.3. Si549 4.3.1.4. Si569 4.3.1.5. Si52202
4.3.2. The Power Functionality x
4.3.2.1. Power Monitor 4.3.2.2. Temperature Monitor
4.3.3. The MAX® 10 Functionality x
4.3.3.1. The System Tab 4.3.3.2. The IO Control Tab
4.3.4. Agilex™ 5 FPGA Functionality x
4.3.4.1. The Configure Menu 4.3.4.2. The Main Info Tab 4.3.4.3. The Transceiver Tab 4.3.4.4. The Memory Tab
4.3.4.3. The Transceiver Tab x
4.3.4.3.1. The FMC+ Tab 4.3.4.3.2. The SFP+ Tab
4.3.4.3.1. The FMC+ Tab x
4.3.4.3.1.1. The FMC+ Test Tab 4.3.4.3.1.2. The FMC+ Status Tab
4.3.4.4. The Memory Tab x
4.3.4.4.1. The COMP0 Tab 4.3.4.4.2. The COMP1 Tab 4.3.4.4.3. The HPS COMP Tab
4.3.5. Other Functionalities x
4.3.5.1. The Diagnostic Functionality 4.3.5.2. The Sys Info 4.3.5.3. The Connection Information 4.3.5.4. The Bottom Info Bar
5. Development Kit Hardware and Configuration x
5.1. Configuring the FPGA and Accessing HPS Debug Access Port by JTAG 5.2. Configuring the FPGA Device by Active Serial (AS) Modes (Default Mode)
6. Custom Projects for the Development Kit x
6.1. Golden Top 6.2. EMIF Pin Swizzling Setting
A. Development Kit Components x
A.1. Board Overview A.2. System Management A.3. Power A.4. Clocks A.5. General Input/Output A.6. Memory Interfaces A.7. Board to Board Connector A.8. Communication Interfaces
A.1. Board Overview x
A.1.1. Board Components
A.7. Board to Board Connector x
A.7.1. Modular Board Primary Connector A.7.2. Modular Board Secondary Connector A.7.3. Carrier Board Primary Connector A.7.4. Carrier Board Secondary Connector
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings Power Supply Hazardous Voltage Power Connect and Disconnect System Grounding (Earthing) Power Cord Requirements Lightning/Electrical Storm Risk of Fire B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Kit Setup
4. Board Test System
5. Development Kit Hardware and Configuration
6. Custom Projects for the Development Kit
7. HPS Boot
8. Document Revision History for the Agilex™ 5 FPGA E-Series 065B Modular Development Kit User Guide
A. Development Kit Components
B. Additional Information

B.1.1. Safety Warnings

Power Supply Hazardous Voltage

AC mains voltages are present within the power supply assembly. No user serviceable parts are present inside the power supply.

Power Connect and Disconnect

The AC power supply cord is the primary disconnect device from mains (AC power) and used to remove all DC power from the board/system. The socket outlet must be installed near the equipment and must be readily accessible.

System Grounding (Earthing)

To avoid shock, you must ensure that the power cord is connected to a properly wired and grounded receptacle. Ensure that any equipment to which this product is attached to is also connected to properly wired and grounded receptacles.

Power Cord Requirements

The plug on the power cord must be a grounding-type male plug designed for use in your region. It must have certification marks showing certification by an agency in your region. The connector that plugs into the appliance inlet of the power supply must be an IEC 320, sheet C13, female connector. If the power cord supplied with the system does not meet requirements for use in your region, discard the cord, and do not use it with adapters. Use only certified power supply cord with appropriate gauge, designed for use in your region.

Lightning/Electrical Storm

Do not connect/disconnect any cables or perform installation/maintenance of this product during an electrical storm.

Risk of Fire

To reduce the risk of fire, keep all flammable materials a safe distance away from the boards and power supply. You must configure the development kit on a flame retardant surface.

Level Two Title