Remote Update Intel® FPGA IP User Guide

Download PDF
ID 683695
Date 7/25/2024
Public
Document Table of Contents
Document Table of Contents x
1. Remote Update Intel® FPGA IP User Guide
1. Remote Update Intel® FPGA IP User Guide x
1.1. Release Information for Remote Update Intel® FPGA IP 1.2. Avalon® Memory-Mapped Interface in Remote Update Intel® FPGA IP 1.3. Arria® 10 and Cyclone® 10 GX Devices 1.4. Arria II, Arria V, Cyclone V, Stratix IV, and Stratix V Devices 1.5. Cyclone IV and Intel Cyclone 10 LP Devices 1.6. Flash Memory Programming Files 1.7. Design Examples 1.8. Remote Update Intel® FPGA IP User Guide Archives 1.9. Document Revision History for the Remote Update Intel® FPGA IP User Guide
1.3. Arria® 10 and Cyclone® 10 GX Devices x
1.3.1. Remote System Configuration Mode 1.3.2. Remote System Configuration Components 1.3.3. Parameter Settings 1.3.4. Ports 1.3.5. Parameters 1.3.6. Avalon® Memory-Mapped Interface 1.3.7. Enabling Remote System Upgrade Circuitry 1.3.8. Generating Initial RSU Image
1.3.1. Remote System Configuration Mode x
1.3.1.1. Remote System Upgrade State Machine
1.3.1.1. Remote System Upgrade State Machine x
1.3.1.1.1. Switching from Factory to Application Image or from Initial Application Image to Other Application Image
1.3.6. Avalon® Memory-Mapped Interface x
1.3.6.1. Control Status Register Signals 1.3.6.2. Register Map
1.3.6.1. Control Status Register Signals x
1.3.6.1.1. Control Status Register Write Operation 1.3.6.1.2. Control Status Register Read Operation 1.3.6.1.3. Operations Example Waveforms
1.4. Arria II, Arria V, Cyclone V, Stratix IV, and Stratix V Devices x
1.4.1. Remote System Configuration Mode 1.4.2. Remote System Configuration Components 1.4.3. Parameter Settings 1.4.4. Ports 1.4.5. Parameters 1.4.6. Avalon® Memory-Mapped Interface 1.4.7. Enabling Remote System Upgrade Circuitry
1.4.6. Avalon® Memory-Mapped Interface x
1.4.6.1. Control Status Register Signals 1.4.6.2. Register Map
1.4.6.1. Control Status Register Signals x
1.4.6.1.1. Control Status Register Write Operation 1.4.6.1.2. Control Status Register Read Operation
1.5. Cyclone IV and Intel Cyclone 10 LP Devices x
1.5.1. Remote System Configuration Mode 1.5.2. Remote System Configuration Components 1.5.3. Parameter Settings 1.5.4. Ports 1.5.5. Parameters 1.5.6. Remote Update Operation 1.5.7. Avalon® Memory-Mapped Interface 1.5.8. Enabling Remote System Upgrade Circuitry
1.5.7. Avalon® Memory-Mapped Interface x
1.5.7.1. Control Status Register Signals 1.5.7.2. Register Map 1.5.7.3. Read Source Mapping
1.5.7.1. Control Status Register Signals x
1.5.7.1.1. Control Status Register Write Operation 1.5.7.1.2. Control Status Register Read Operation
1.7. Design Examples x
1.7.1. Intel Arria 10 Remote Update Design Example 1.7.2. Cyclone® V Remote Update Design Example
1. Remote Update Intel® FPGA IP User Guide

1.3.1.1. Remote System Upgrade State Machine

After power-up and exit POR, the remote system upgrade registers are reset to 0 and the factory or application configuration image is loaded based on the start address stored at 0x00 to 0x1F in the configuration device or QSPI flash. The Remote Update Intel® FPGA IP core enables you to perform the following remote update functions once the factory or an application image is loaded successfully:

  • Switch from factory image to application image
  • In DTA mode, switch from initial application image to others application image

The configuration mode (AnF) bit is by default set to 0 in the DTA mode, the AnF bit cannot be used to indicate the type (such as factory or application image) of image loaded into the FPGA. In the DTA mode, the watchdog timer is disabled by default. You cannot enable the watchdog timer in the initial or first application image loaded upon powering up the device. You can enable the watchdog timer feature when you perform remote update from the initial application image to other application image.


Section Content
Switching from Factory to Application Image or from Initial Application Image to Other Application Image

Level Two Title